HunterDouglas Nantucket EasyRise Manual de operación

Installation And

Care Instructions

EasyRise™Shadings

Nantucket™Window Shadings

THANK YOU for purchasing a Hunter Douglas product. Your new

window shading has been custom built for you from the highest

quality materials. Once in your window, it will provide you with a

lifetime of beauty and trouble-free use.

Getting Started

Remove the window shading from the package. Keep the

packaging until the shading operates to your satisfaction.

Check the diagram to make sure you have the necessary parts.

Tools needed for installing your Nantucket™ shading:

Flat blade and

Phillips screwdrivers

Level

Measuring tape

Pencil

Pliers

Power drill, 1/4" hex driver, and drill bits

•

Continuous

Cord Loop

Fabric

(Front)

Bottom Rail

Cord

Tensioner

End Cap

Hold-Down

Bracket

(Optional)

Dust Cover

(Optional)

Back Cover

(Optional With

Inside Mounts)

Headrail

End Cap

Bottom Rail

Weight

Clip

Weight

Clip

Fabric

Vanes

Headrail

Limit

Stop

Spacer

Block

(Optional)

Installation

Bracket

Extension

Bracket

(Optional)

Limit

Stop

Fabric

(Rear)

For assistance, call the Hunter Douglas

Customer Information Center

at 1-888-501-8364

Visit our Web site at hunterdouglas.com

Extension

Bracket

11/4"

Minimum

Depth

11/8"

Minimum

Mark

On Wall

Center each bracket over a mark

on the mounting surface.

Adjust bracket placement

to accommodate any obstructions

to the bottom rail, such as window

cranks or handles.

Check that each bracket is level and

the front edges are aligned. Use the

removed tabs as shims, if necessary.

Attach using two screws through the

top holes.

NOTE: Failure to level and align the brackets may prevent them from

functioning properly.

Back Cover Installation (Optional)

If using the back cover, use pliers

to break off both tabs on the

installation brackets. Remove the

tab on the back cover bracket.

Snap the prongs on the back cover

brackets into the holes on the back

of the installation brackets.

After bracket installation, install the

cover into the back cover bracket.

Outside Mount Applications

Bracket Installation

Center the shading over the window and

mark the ends of the headrail.

Measure 2" in from the marks

on the wall and mark the

bracket locations.

Use pliers to break off both tabs

on each mounting bracket.

Center each bracket over the

marks on the mounting surface.

Adjust bracket position to accommodate any obstructions to the

bottom rail, such as window cranks or handles.

Check that each bracket is level and the tops are aligned. Use the

removed tabs as shims, if necessary.

Attach using two screws through the rear holes.

Spacer Blocks (Optional)

Each spacer block projects brackets ½" from the mounting surface.

Mount spacer blocks with the solid

side facing the mounting surface.

Use two mounting screws.

Screws should be long enough

to secure the bracket to the

mounting surface.

Use a maximum of three spacer

blocks per bracket.

End Mount Applications

End mount the headrail when conventional

mounting techniques will not work, for

example, in an arched window.

Mount the extension brackets on a surface at

least 1¼"wide.

Attach the installation brackets to the

extension brackets using the machine screws

and nuts provided.

•

In addition, you will need fasteners designed to work with your

specific mounting surfaces:

Contents of the hardware package may vary depending upon how the

shading was ordered and how the shading will be mounted.

Mount The Installation Brackets

Bracket Placement

Measure 2" in from the ends of the headrail and mark the bracket

location on the mounting surface.

Bracket placement is the same for inside and outside mounts.

CAUTION: Do not push down on the limit stops. Limit stop angle

is set at the factory. Over-adjusting the limit stop is not reversible and

may damage the shading.

The number of brackets is determined by the shading width.

Inside Mount Applications

The minimum depth depends on the headrail.

NOTE: Add ¼" to the minimum depth if using the optional

back cover.

Bracket Installation

Use pliers to break off the upper tab of each

bracket. If using the back cover option, see

next section, Back Cover Installation.

NOTE: Remove the bottom tab on each

installation bracket only if it interferes with the

bracket installation.

•

Back

Cover

Back Cover

Bracket

Installation

Bracket

Limit Stops (5

" From Ends)

Space EvenlySpace Evenly

Normal Spacing (Shadings Over 36" Wide):

Limit Stops (2" From Ends)

Space Evenly

Obstruction Spacing (Maximum):

Space Evenly

Removable

Tabs

Installation

Bracket

Remove

This Tab

Back

Cover

Bracket

Spacer

Block

1/2"

Mounting Surface Fastener

No. 6 Hex Head Screws

(Provided)

Wall Anchors, Expansion Bolts

(Not Provided)

Wood

Drywall, Plaster

Sheet Metal Screws

(Not Provided)

Metal

Oversized Headrail Oversized Headrail

Fully Recessed

1" 3¼"

Minimum

Depth

(See Chart)

Shade Width Brackets Required

12" - 36" 2

361/8" - 79" 3

791/8" - 96" 4

96" - 120 5

Adjust The Bottom Rail Weight

To release, insert a flat blade screwdriver

into a weight clip and turn clockwise.

Move the weight in 1" increments

toward the side where the fabric

is gathering.

Secure the weight clips in position by turning them

counterclockwise after making the adjustment.

Test and, if necessary, adjust again.

NOTE: Skew adjustment is not possible by moving the limit

stop assemblies.

Attach The Accessories

Install The Cord Tensioner

See the Universal Cord Tensioner Installation Instructions included with

the cord tensioner.

Attach The Dust Cover (Optional)

Use the entire cover on outside mounts.

On inside mounts, trim the cover along a score to fit over the portion

of the headrail that protrudes from the window frame.

Cut the cover to fit between extension brackets, when used.

Peel the backing from the double-sided tape to attach the cover to

the headrail.

Attach The Hold-Down Brackets (Optional)

Hold-down brackets secure the bottom rail to the sill when the

window shading is fully lowered. The bottom rail can still pivot when

opening and closing the vanes, but the

shading cannot be raised.

With the shading fully lowered,

insert the pin on the hold-down

bracket into the hole on the bottom

rail end cap.

Mark the mounting hole locations

on the mounting surface.

Center the hold-down brackets over

the mounting hole locations and check their alignment. Attach

using two screws.

NOTE: Disconnect the bottom rail from the hold-down brackets to

raise the shading.

•

Fabric Roll

Bottom Rail Move Weight

Overhead View – No Dust Cover

Dust Cover (Outside Mount)

Dust Cover (Inside Mount)

Cut Along A Score To Size The Dust Cover

To Fit Any Exposed Part Of The Headrail Assembly

Hole

Back Of

Shading

NOTE: Add ¼" to the minimum depth if using the optional

back cover (see Inside Mount Applications).

CAUTION: For end mounting shadings wider than 48" into material

other than a secure wall stud, use medium to heavy-duty wall anchors

(not provided) matched to the wall thickness. Failure to mount the

brackets securely may result in injury or property damage.

Install The Shading

Hold the shading so

the front faces you.

Push the top edge of

the headrail under the

locking tab on the

installation bracket

until it snaps into

place. The locking tab

will be visible.

WARNING: Failure to snap the headrail securely into the

installation bracket and engage the locking tab may cause the

shading to release unexpectedly.

Operate The Shading

Pull the rear cord of

the cord loop to lower

the shading.

With the shading fully

lowered, continue to

pull the rear cord to

tilt the bottom rail

and open the vanes.

Pull the front cord of

the cord loop to close

the vanes and raise

the shading.

•

4Adjust The Shading

Test The Shading

Lower the shading, then slowly raise it.

If the fabric rolls unevenly or rubs against the end cap,

check that the headrail is level. Level, if necessary.

If the headrail is level, adjust the bottom rail weight.

•

Weight

Clip

Weight

Clip

Headrail

Flange

Locking Tab

Installation

Bracket

Push Until

Locking Tab

Secures

Headrail

12453

HunterDouglas

Front Side Of Shading

Remove The Shading

Fully raise the shading.

Use the quick release

card to release the

locking tab on the

mounting brackets and

remove the shading

from the brackets.

Care And Cleaning

Nantucket™window shadings are made of 100% polyester, which

means they are inherently durable and resilient. However, care must

be taken to avoid wrinkling the fabric, particularly where the vanes

meet the facings.

Dusting

Regular light dusting with a feather duster is all the cleaning that is

needed in most circumstances.

Vacuuming

Use a low suction, hand-held vacuum for more

thorough dust removal.

Forced Air

Blow away dirt and debris between the vanes using clean compressed air.

Spot-Cleaning

Do not spot-clean Nantucket window shadings.

Ultrasonic Cleaning

Nantucket shadings can be ultrasonically cleaned by a professional,

with the exception of Misty Harbor™light-dimming fabric.

Specify that a mild detergent solution be used.

Never immerse the headrail in the solution.

Dry the shading completely in the lowered position.

Electrostatic Cleaning

Do not use electrostatic cleaning devices such as Swiffer™or Pledge

Grab-it™on any Nantucket window shadings.

For more comprehensive cleaning instructions, call the

Hunter Douglas Customer Information Center toll free at:

1-888-501-8364

A Note About Nantucket Fabric

As with all textiles, Nantucket fabric is subject to some variations.

Slight wrinkling, puckering, or bowing is inherent to this textile

product and should be considered normal, acceptable quality. These

characteristics are not usually visible from the front or rear but may

be visible from a side angle.

Precautions should be taken to reduce exposure to harsh environmental

elements, such as salt air. Continuous exposure through open

windows and doors will accelerate the fabric deterioration.

•

™ Trademark of Hunter Douglas Inc. Patented in the U.S. and foreign countries.

Other U.S. and foreign patents pending. Swiffer™is a trademark of Procter & Gamble Company.

Pledge Grab-it™is a trademark of SC Johnson.

PCN 5107127000 Rev. 10/06

Child Safety

Headrail

Installation

Bracket

Lift Locking Tab To

Release Headrail

Insert Card

Between

Headrail And

Locking Tab

CORD TENSIONER

INSTALLATION

GUIDE

Hunter Douglas provides a cord tensioner and we

recommend its use.

•

WARNING

Young children can STRANGLE in cord and bead

chain loops. They can also wrap cords around their

necks and STRANGLE.

Always keep cords and bead chains out of

children’s reach.

Move cribs, playpens and other furniture away

from cords and bead chains. Children can climb

furniture to get to cords.

Attach tension device to wall or floor. This can

prevent children from pulling cords and bead

chains around their necks.

For more safety information call 1-888-501-8364 in

the U.S. or 1-866-662-0666 in Canada.

Troubleshooting

Problem Solution

Vanes do not align

on side-by-side

shadings.

Vane alignment is only guaranteed within

1/4" when shadings are ordered at the

same time, at the same height, with the

same color and when specified on the

order form.

Check that the windows are square and

the same height.

•

The shading is

hard to raise or

lower, or will not

raise or lower.

Shadings cannot be forced into tight

inside-mount window openings. If an

inside mount, check that the shading

is installed correctly. Make sure there is

clearance between the ends of the shading

and the window casement. See Step 1.

Check that the installation brackets are

level. Shim to level, if necessary. See Step 1.

If hold-down brackets are used, make sure

they have been released. See Step 5.

Make sure the fabric is not caught.

•

The shading raises

or lowers unevenly

or the bottom rail

is uneven when

fully raised.

Check that the window is square by

measuring the diagonals.

Check that the installation brackets are

level. Shim to level, if necessary. See Step 1.

Adjust the bottom rail weight. See Step 4.

•

The shading will

not snap into

the installation

brackets.

Check that the installation brackets are

aligned and level. See Step 1.

Check that the locking tab on the

installation bracket slides over the

headrail. See Step 2.

•

Otros manuales de Persiana de ventana de HunterDouglas

HunterDouglas

HunterDouglas RB 500 Guía de seguridad

HunterDouglas

HunterDouglas Pirouette PowerView+ Gen 3 Automation Manual de lista de piezas

HunterDouglas

HunterDouglas Designer Roller Shades Manual de lista de piezas

HunterDouglas

HunterDouglas Vignette Traditional Manual de usuario

HunterDouglas

HunterDouglas Decor Standard Cordlock Manual del propietario

HunterDouglas

HunterDouglas Reveal Manual de lista de piezas

HunterDouglas

HunterDouglas LiteRise Manual de operación

HunterDouglas

HunterDouglas Alustra Woven Textures Manual de usuario

HunterDouglas

HunterDouglas PowerView M40T Manual de usuario

HunterDouglas

HunterDouglas RB 500 Guía de seguridad

HunterDouglas

HunterDouglas DecoFlex WireFree Telis Instrucciones de funcionamiento

HunterDouglas

HunterDouglas Duette Honeycomb Shades Manual de usuario

HunterDouglas

HunterDouglas Standard Cordlock, Moveable Slat Specialty... Guía del usuario

HunterDouglas

HunterDouglas PowerView Venetian Blind 18VDC Manual de usuario

HunterDouglas

HunterDouglas EverWood Guía del usuario

HunterDouglas

HunterDouglas Country Woods Manual de operación

HunterDouglas

HunterDouglas Silhouette Halo Duolite Manual de lista de piezas

HunterDouglas

HunterDouglas LiteRise Manual de usuario

HunterDouglas

HunterDouglas LiteRise Manual de lista de piezas

HunterDouglas

HunterDouglas Paramount Headrail Systems Manual de lista de piezas

HunterDouglas

HunterDouglas Luxaflex PowerView Manual de usuario

HunterDouglas

HunterDouglas Silhouette Nantucket PowerView Gen 3... Manual de lista de piezas

HunterDouglas

HunterDouglas Standard Hardware System Manual de lista de piezas

HunterDouglas

HunterDouglas VS 100 Guide rail Guía de mantenimiento y servicio

Manuales populares de Persiana de ventana de otras marcas

Jysk

Jysk ROGEN Manual de usuario

SOMFY

SOMFY 1241752 Manual de usuario

Rollos

Rollos S-Nanorollo V2 Guía de planificación

Teptron

Teptron Move Manual de usuario

Renson

Renson Outdoor Loggia Guía de seguridad

Project Source

Project Source CDLF2342W Manual de usuario

Domondo

Domondo PureNight Manual de instrucciones de instalación

rollease acmeda

rollease acmeda Easy Spring Air Guía de configuración

IKEA

IKEA KADRILJ Manual de usuario

Hallis Hudson

Hallis Hudson Rolls Super glide Manual de usuario

Benthin

Benthin P1614 Manual de usuario

MV LINE

MV LINE CLARA 015 Manual de instrucciones

Current

Current E-WAND Guía

weinor

weinor VertiTex ZipR Manual

Roto

Roto ZAR M R4/R7 Manual de usuario

SOMFY

SOMFY Movelite WT Series Manual de usuario

Acmeda

Acmeda RF400 Series Manual de usuario

Motura

Motura Pli_353/3 Manual de usuario