Hubbell Laredo Manual de usuario

STEP I

MOUNTING PREPARATION

CAUTION: FIXTURE WEIGHTS ABOUT 30 POUNDS

• Using template (A) lay over junction box (B) on the wall.

Mark at (3) hole. (See Fig.1)

• Drill wall for the hardware appropriate for the type wall.

Use 1/4 diameter bolt.

• Pull the supply wires (C) from junction box (B) .

STEP II

FIXTURE MOUNTING PREPARATION

(See Fig. 2)

• To open door (E), loosen (2) retaining screws (F).

• For optional quick release door latch, push pin (D) to open

door (E).

• Loosen (4) screws (X) and them remove reflector (H).

• Loosen screws (O), remove cover (P) and discard.

STEP III

FIXTURE MOUNTING

(See Fig.3)

• Insert all wires (C) through slit on gasket opening at the

back of housing.

• Hang fixture on the mounting hardware at the wall through

key-slots opening (J).

• Tighten bolts (K) securely.

• Apply caulking sealant around the top and two sides of the

housing.

Step IV

WIRING

(See Fig. 3)

• POWER MUST BE OFF.

(WIRING MUST BE PERFORMED BY

A QUALIFIED ELECTRICIAN)

• Wire service leads to fixture power leads according to local

and National Electric Codes.

• For direct wire connections, connect ground wire to green

wire then push ware back to J-box on the wall. Connect

black to black and white to neutral then push connections

back inside J-box (B).

• When supplied with optional terminal block (L) or fuseblock

(M) connect service leads to these devices.

FOR THROUGH WIRING USING CONDUIT

• Remove hole plug (N) for the conduit entry

• Use pipe sealant before engaging conduit fittings to prevent

water leakage.

• Loosen screw (O) and remove wire cover (P).

• Insert fixture lead wires (Q) through grommet ( R ).

• Make the wire connections.

• Replace cover (P) making sure not to pinch wires.

INSTALLATION INSTRUCTIONS FOR WALLPACK LUMINAIRE

Outdoor Lighting

laredo

WARNING: DISCONNECT POWER BEFORE INSTALLATION OR MAINTENANCE.

READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL

LUMINAIRE, FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN

PERSONAL INJURY AND/OR PROPERTY DAMAGE.

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

STEP V

LAMPING

• Make sure that the lamp size and type matches the ballast

specifications.

• Replace reflector (H).

• Engage the lamp to socket (S).

• For medium base lamps – to ensure proper contact, loosen

the lamp one turn then retighten.

STEP VI

RE-LAMPING USING POLE STICK

(By others)

(See Fig.4)

CAUTION:

WEAR SAFETY GOGGLES IN THE EVENT LAMP BREAKS

• Using the other end of the pole, push latch pin (D) and

slowly lower the door to open position.

• Align lamp changer (U) with the lamp, then slowly push up

to engage. Unscrew to remove lamp.

• Attach the replacement lamp to head changer (U), align

with the socket and screw in to engage.

• To close door use again the other end of the pole, raise the

front end of the door up to engage latch.

REMOVING FRONT DIRECTOR FOR IMPROVING

FORWARD THROW BEAM DISTRIBUTION.

• Loosen (4) retaining screws (X) and remove reflector (H).

• Unbend the two tabs to remove the front director (Z).

STEP VII

INSTALLING VANDAL SHIELD

(See Fig. 5)

• Open door (E) by loosening retaining screws (F).

• From the inside on each (4) bosses adjacent to the lens

clips, drill the door through using .173” diameter No.17 drill

bit.

• Install vandal shield (Y) using (4) self-threading screws (V)

provided.

• Remove metal chips and replace door.

STEP VIII

PBT PHOTOCONTROL FIELD INSTALLATION

(See Fig. 6)

• Remove hole plug (N) from the side of housing.

• Install photocontrol switch (PC) from the inside of housing

using gasket (gg) and nut (nn).

PT. NO. 93002010

Outdoor Lighting

laredo

INSTALLATION INSTRUCTIONS FOR WALLPACK LUMINAIRE

Tabla de contenidos

Otros manuales de Equipo de iluminación de Hubbell

Hubbell

Hubbell Laredo LMC Manual de usuario

Hubbell

Hubbell DUAL LITE EVE Series Manual de usuario

Hubbell

Hubbell M-7679 R-PAC Manual de usuario

Hubbell

Hubbell ALFW-6LU-5KBZ Series Manual de usuario

Hubbell

Hubbell KILLARK VSQ Series Manual del propietario

Hubbell

Hubbell Dual Lite EZ-2R Series Manual

Hubbell

Hubbell Kim Lighting Lightvault LTV59 Manual de usuario

Hubbell

Hubbell Compass CU2SO Manual de usuario

Hubbell

Hubbell Prescolite LBSLEDA Manual de usuario

Hubbell

Hubbell Dual-Lite DYNC C1D2 Series Manual de usuario

Hubbell

Hubbell Dual Lite EV Series Manual

Hubbell

Hubbell DUAL LITE LN4X Series Manual del propietario

Hubbell

Hubbell G040 Manual de instrucciones

Hubbell

Hubbell Dual-Lite EV4D-02WAL Series Manual

Hubbell

Hubbell Dual-Lite EVHC-BC Series Manual

Hubbell

Hubbell NutriLED Series Manual de usuario

Hubbell

Hubbell DUAL LITE PG Series Manual de usuario

Hubbell

Hubbell KILLARK VEB Series Manual de instrucciones

Hubbell

Hubbell KIM LIGHTING VRB1 Manual de usuario

Hubbell

Hubbell KIM LIGHTING LIGHTVAULT LTV55 Manual de usuario

Hubbell

Hubbell Litecontrol 22L Series Manual de usuario

Hubbell

Hubbell SAVVANO Manual de usuario

Hubbell

Hubbell DUAL LITE N4X4 Manual de usuario

Hubbell

Hubbell LITEFRAME LC4 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario