Hubbell NXP2 Series Manual de usuario

Page 1/2 Rev. 03/17/21

3483A_NXP2-RL_SPEC

701 Millennium Blvd • Greenville, SC 29607 / Tel 864.678.1000 / hubbellcontrolsolutions.com

FEATURES

• Robust mechanically latching single and double pole relays

• Electrically rated for 60,000+ operations (30,000+ cycles) at full

20a load

• Mechanically rated for 120,000+ operations (60,000+ cycles)

• Short Circuit Current Rating (SCCR) of 14,000A @ 277VAC

• Manual override switch (integral to the relay)

• At-A-Glance ON/OFF relay status indicator

• 5 year limited warranty

BROCHURE DIMENSIONAL DRAWINGS NX DESIGN & APPLICATION GUIDE

NXP2 SERIES

NX LIGHTING CONTROL PANEL RELAYS

DATE: LOCATION:

TYPE: PROJECT:

™

CATALOG #:

RELATED PRODUCTS

NX Lighting Control Panel -

NXP2 Series

NX Panel Relay Channel Barrier

CONSTRUCTION

• Relay Dimensions

• Single Pole - L:106.5mm x W:24.5mm

x H:60mm

• Double Pole – L:96mm x W:49.5mm

x H:60mm1

MOUNTING

• Mounts directly to NX Lighting Control Panel

relay mounting strap

ELECTRICAL

• Relay Operating Voltages

• Single Pole (p/n NXP2-RL-SP):

• General Use: 20A @ 300VAC

• Tungsten: 2400W @ 120VAC

• (Standard) Ballast: 20A @ 300VAC

• Electronic Ballast: 16A @ 277VAC

• Motor Starting: ½ HP @ 110-125VAC;

1.5 HP @ 220-277VAC

• Double Pole (p/n NXP2-RL-DP):

• General Use: 20A @ 480VAC

• Tungsten: 2400W @ 120VAC

OPERATING ENVIRONMENT

• Indoor use only

• 32° to 112°F (0° to 50°C)

• Relative humidity (non-condensing):

10% to 90%

CERTIFICATIONS

• UL Listed

• CSA Approved

WARRANTY

• 5 year limited

• See HCS Standard Warranty for

additional information

SPECIFICATIONS

ELECTRICAL (CONTINUED)

• Double Pole (p/n NXP2-RL-DP) (Continued):

• (Standard) Ballast: 20A @ 480VAC

• Motor Starting: ½ HP @ 110-125VAC;

1.5 HP @ 220-277VAC

• Relay Electrical Ratings

• Rated for minimum 60,000+ operations

(30,000+ cycles) at full 20A load

• Short Circuit Current Rating (SCCR) of

14,000A @ 277VAC

• Rated full-life with HID load

• Relay Mechanical Ratings

• Rated for minimum 120,000+ operations

(60,000+ cycles)

OPERATON

• Mechanically latching

• Provides at-a-glance indication of ON or OFF

relay status

• Includes manual override switch (integral to

the relay)

Notes:

Double pole relays occupy (2) relay spaces.

ORDERING GUIDE

Example: NXP2-RL-SP

CATALOG #

NXP2-RL –

Model Type

NXP2-RL

NX Lighting Control Panel V2 Relay

SP Single Pole - General Use: 20A @ 300VAC; Tungsten: 2400W @ 120VAC; (Standard) Ballast: 20A @ 300VAC; Electronic Ballast: 16A @

277VAC; Motor Starting:

HP @ 110-125VAC;

HP @ 220-277VAC

DP Double Pole - General Use: 20A @ 480VAC; Tungsten: 2400W @ 120VAC; (Standard) Ballast: 20A @ 480VAC; Motor Starting:

HP @

110-125VAC; 1.5HP @ 220-277VAC

Single Pole Relay Double Pole Relay

NXP2 SERIES

NX LIGHTING CONTROL PANEL RELAYS

Page 2/2 Rev. 03/17/21

3483A_NXP2-RL_SPEC

DATE: LOCATION:

TYPE: PROJECT:

CATALOG #:

701 Millennium Blvd • Greenville, SC 29607 / Tel 864.678.1000 / hubbellcontrolsolutions.com

DIMENSIONS

4.5"

(49.5mm)

2.40"

(60mm)

3.54"

(90mm)

3.78"

(96mm)

BLUE

RED

4.19"

(106.5mm)

0.96"

(24.5mm)

2.40"

(60mm)

3.54"

(90mm)

Blue

Red

Double Pole RelaySingle Pole Relay

Relay Wiring Diagrams

SIMLXRL1 - Simplicity LX Single Pole Relay

SIMLXRL2 - Simplicity LX Double Pole Relay

Installation Instructions

Hubbell Building Automation, Inc.

9601 Dessau Road • Building One • Suite 100

Austin, Texas 78754

512-450-1100 • 512-450-1215 Fax

www.hubbell-automation.com

Overview

This document provides instructions for installing and connecting Single and/or Double Pole Relays in the Simplicity LX Series Lighting

Control Panel.

Contents

These instructions include information as follows:

Description

General Precautions

Installation

Precautions

• Read and understand all instructions before beginning installation.

• For installation by a qualified electrician in accordance with National and/or local Electrical Codes and the following instructions.

•RISK OF ELECTRICAL SHOCK. Turn power off at breaker panel before servicing unit. Never wire energized electrical components.

Never operate unit with door panel or relay guards removed.

•USE COPPER CONDUCTOR ONLY.

• Confirm that device ratings are suitable for application prior to installation.

• Use only approved materials and components (i.e. wire nuts, electrical box, etc.) as appropriate for installation.

•NOTICE: Do not install if any damage to product is noticed.

Installation

1. Verify that power is turned off at breaker panel before installing relay in panel.

2. Remove panel door assembly from panel enclosure.

3. Locate an open relay position (two adjacent positions for a double pole relay) in the panel and remove the relay guard cover(s).

4. Insert relay into mounting bracket noting proper orientation of input/output sides. Verify that relay is securely held in mounting bracket.

5. Connect relay input and output as shown in the wiring diagram below. Connect input to panel I/O control card using relay connector

cable. Attach red lead to red screw and blue wire to blue screw. Slide connector on to header pins of I/O control card. Connect line and

load leads to relay output.

Figure 1: Relay wiring diagrams

Load

(to lighting system)

Load, Phase 2

(to lighting system)

Load, Phase 2

(

from Circuit Breaker)

Load, Phase 1

(to lighting system)

Load, Phase 1

(to lighting system)

Blue Input Screw

Blue Lead

Red Input Screw Red Lead

Relay Connector

I/ O cont ro l

Card Head

(Polarized)

Blue Input Screw Blue Lead

Red Input Screw

Red Lead

Relay Connector

I/ O cont ro l

Card Head

(Polarized)

Line

(

from Circuit Breaker)

Single Pole Relay

Double Pole Relay

WIRING DIAGRAM

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de Hubbell

Hubbell

Hubbell VSLT-UP Manual de usuario

Hubbell

Hubbell PRS Manual de usuario

Hubbell

Hubbell homeSELECT RMS100 Manual de usuario

Hubbell

Hubbell Dual-Lite EV4D-02WAL Series Manual

Hubbell

Hubbell Laredo LMC Manual de usuario

Hubbell

Hubbell Laredo LMC Manual de usuario

Hubbell

Hubbell Litecontrol 22L Series Manual de usuario

Hubbell

Hubbell Dual-Lite UFO-LP1 Manual de usuario

Hubbell

Hubbell DUAL LITE N4X4 Manual de usuario

Hubbell

Hubbell M-7679 R-PAC Manual de usuario

Hubbell

Hubbell Dual-Lite EVHC-BC Series Manual

Hubbell

Hubbell KIM LIGHTING VRB1 Manual de usuario

Hubbell

Hubbell KIM LIGHTING LIGHTVAULT LTV55 Manual de usuario

Hubbell

Hubbell DUAL LITE PG Series Manual de usuario

Hubbell

Hubbell KILLARK VSQ Series Manual del propietario

Hubbell

Hubbell LITEFRAME LC4 Manual de usuario

Hubbell

Hubbell Kim Lighting Lightvault LTV59 Manual de usuario

Hubbell

Hubbell DUAL LITE EVE Series Manual de usuario

Hubbell

Hubbell Dual Lite EZ-2R Series Manual

Hubbell

Hubbell SAVVANO Manual de usuario

Hubbell

Hubbell ExpressLine Miniliter IV MHSY Series Manual de usuario

Hubbell

Hubbell Dual Lite EV Series Manual

Hubbell

Hubbell NutriLED Series Manual de usuario

Hubbell

Hubbell WPH Series Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario