Hubbell KILLARK VSQ Series Manual del propietario

P/N 00912317 FORM NO. K1218 R0916 ECO 7-023-16

Side 1 of 2

HUBBELL INCORPORATED (Delaware)

2112 Fenton Logistics Park Blvd

Fenton, Missouri 63026 USA

INSTALLATION, OPERATION & MAINTENANCE DATA SHEET

VSQ SERIES 60 AMP INTERLOCKED SWITCHED RECEPTACLES

APPLICATIONS

•

VSQ series dead front interlocked receptacle with

switch is suitable for use in hazardous locations.

•

Designed for supplying power to fixed or portable

electricalequipment.

ELECTRICAL RATING

•

Maximum voltage - 600 VAC @ 50-400Hz.

Continuous Current - 60Amperes.

INSTALLATION

•

Carefully Read and understand the following

instructions before installation & operation of this

device.

•

Note: All Installations must comply with Applicable

Local, National Electrical Code and/or Canadian

ElectricalCode.

•

Note: VSQ covers can not be used on VWSQ

mounting boxes, which are intended for non-

hazardous location installations.

•

Warning: Make sure the receptacle assembly is

suitable for use in desired location per applicable

local

and/or National Electrical Code. Serious

damage

and/or injuries may result due to improper

applications. Electrical power must be turned OFF

before and during the installation & maintenance.

Fatal injury and/or damage may result by not

following these instructions.

•

Mounting Arrangement: Receptacle assembly must

be mounted securely onto a column, wall, or other

structure that is able to support the device and the

associated conduit system. The structure is to be

prepared for use of four (4) 3/8” steel bolts (furnished

by others) using the lugs on the housing. The

spacings are as shown in Fig. 1. The device is

equipped with factory installed hinges. It must be

mounted with the hinges on the left and the

receptacle

in the downward direction.

•

Conduit Installation:

1 1/2” NPT conduit entries are provided on the top

and bottom of the housing.

All conduit entries must be sealed within 18” of the

enclosure as per National Electrical Code.

Make sure conduit entries are clean before

installing conduit, close-up plugs, reducers, etc.

Killark “LUBG” thread lubricant is recommended for

this application.

Warning: Use only copper cable or wire for the range

indicated in the table. Use 75°C rated conductors

(minimum).

Wire Range

Strip Length

Torque

Switch

#6 - #4

0.750 inches

30 in.-lb.

Ground

#16 - #6

0.500 inches

30 in.-lb.

•

Wiring:

Develop and establish the wiring pattern for your

system. Locations having different voltages and/or

frequencies must not have interchangeable

attachment plugs. Always test before energizing.

Make sure to pull sufficient length of supply

conductors to connect to the enclosed terminals.

Strip the conductors to the length shown in table.

Connect the conductors to the ground and phase

terminals securely and tighten to the values shown in

the table.

•

Inspect & Clean Flange: The machined flange

surface of both the box and cover must be smooth,

free of nicks, scratches, dirt, or any foreign particle

build-up that would prevent proper seating. Surfaces

must seat fully against each other to provide a proper

flame path joint. Clean surfaces by wiping with a

clean, lint free cloth. Apply a light coating of “LUBG”

lubricant to flange surface.

•

Cover Securement: Close the cover then install and

tighten all cover bolts to 25 ft.-lb. Make sure no cover

bolts are omitted. Use only those bolts supplied with

the device. Check the bolted joint with a .0015” feeler

gauge. The gauge must not enter the joint more than

1/8” at any point.

•

Caution: Missing bolts or an improper joint can result

in an explosion, creating the potential for serious or

fatal physical injury and/or property damage.

•

Cover Replacement: The power must be

disconnected before removing the cover. Remove the

bolts and reverse the wiring procedure. Once the

conductors have been detached, remove the screws

that hold the cover to the hinges (4 total). Line up the

new cover with the hinges and reinstall the hinge

screws. Once the hinges are attached repeat the

wiring, inspect & clean flange and cover securement

procedures.

CLASS I, GROUPS B,C,D; CLASS I ZONE 1, GROUPS IIB, IIA +H2; CLASS II, GROUPS F & G; & CLASS III

HAZARDOUS LOCATION ENCLOSURE TYPES 3, 4, 4X & 12.

All Installations Must Comply With Applicable Local,

National Electrical Codes, and/or Canadian Electrical

Code.

To Prevent Ignition of Hazardous Atmospheres Do Not

Use in Class II, Group E Locations that Contain

Electrically Conductive Dusts.

P/N 00912317 FORM NO. K1218 R0916 ECO 7-023-16

Side 2 of 2

OPERATION

•

Caution: The switch cannot be turned ON without

fully inserting an approved plug (see list below). A

plug cannot be inserted or withdrawn unless the

switch is OFF. To remove the plug turn the switch to

the OFF position and pull back on the locking pin

knob while pulling on the plug.

•

Note: Switch cannot be operated until the locking pin

has fully engaged the plug.

ROUTINE INTERLOCK VERIFICATION

•

Warning: Perform this test before energizing the

receptacle.

•

Before inserting the plug verify that the switch can

not be turned to the ON position.

•

Insert the plug, turn the switch to the ON position, pull

on the locking pin knob and verify that the plug can

not be withdrawn without turning the switch to the

OFF position.

•

If the receptacle does not perform

properly

discontinue use immediately!

ELECTRICAL TEST

•

Warning: Perform this test before energizing the

receptacle.

•

Test continuity of wiring to verify correct polarity,

phasing, and grounding connections.

•

Measure insulation resistance to be sure the system

does not have any shorts or unwanted grounds.

MAINTENANCE

•

Electrical and mechanical inspection of all

components must be performed regularly. It is

recommended that an inspection be performed a

minimum of once a year.

•

Inspect all terminals for tightness (Retorque).

Discoloration due to excessive heat is an indicator of

possible problems and should be thoroughly

investigated and repaired as necessary.

•

Inspect grounding and bonding for correct installation

and secure connection (Retorque).

•

Warning: Do not modify these devices in any way.

Replace with proper replacement part(s) supplied by

Killark before continuing service. Failure to do so

could cause serious or fatal personal injury and/or

equipmentdamage.

•

Inspect gaskets for deterioration and replace if

necessary.

•

Clean exterior surfaces making sure nameplates

remain legible.

•

Torque all bolts and screws as described in the

instructions before reusing the device.

•

Inspect receptacle thread used for plug locking ring

for proper lubrication. Apply Killark “LUBG” type

lubricant or equivalent to thread surfaces as required

to prevent galling between the receptacle and locking

ring threads.

•

In addition to these required maintenance

procedures, we recommend an Electrical Preventive

Maintenance Program as described in the National

Fire Protection Association Bulletin NFPA No. 70B.

•

Replacement Parts: (Cover Only)

VSQ6023-COV

VSQ6034-COV

VSQ6023-S37-COV

VSQ6034-S37-COV

•

Note: The S37 suffix designates a polarized

receptacle.

FIGURE 1

INTERMATEABILITY FORPLUGS

Device

Killark Plug

Crouse Hinds Plug

Appleton Plug

VSQ6023

VP6385

APJ6385, NPJ6383, NPJ6384

ACP6023BC

VSQ6034

VP6485

APJ6485, NPJ6483, NPJ6484

ACP6034BC

VSQ6023-S37

VP6385-S37

APJ6385-S4,NPJ6383-S4,NPJ6384-S4

ACP6023BC-P4

VSQ6034-S37

VP6485-S37

APJ6485-S4,NPJ6483-S4,NPJ6484-S4

ACP6034BC-P4

WARNING

Electrical power supply MUST BE OFF before and

during installation and maintenance. DISCONNECT

primary power source and LOCK OUT. Installations and

maintenance procedure must be performed by a trained

and competent electrician

WARNING

If any parts of the plug, receptacle, or switch appear to

be missing, broke, or show the signs of damage.

DISCONTINUE USE IMMEDIATELY!

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Hubbell

Hubbell

Hubbell Prescolite LBSLEDA Manual de usuario

Hubbell

Hubbell WPH Series Manual de usuario

Hubbell

Hubbell Litecontrol 22L Series Manual de usuario

Hubbell

Hubbell SAVVANO Manual de usuario

Hubbell

Hubbell NutriLED Series Manual de usuario

Hubbell

Hubbell DUAL LITE EVE Series Manual de usuario

Hubbell

Hubbell Dual Lite CVEC15 Manual de usuario

Hubbell

Hubbell DUAL LITE PG Series Manual de usuario

Hubbell

Hubbell DUAL LITE LN4X Series Manual del propietario

Hubbell

Hubbell Laredo Manual de usuario

Hubbell

Hubbell M-7679 R-PAC Manual de usuario

Hubbell

Hubbell Dual-Lite EV4D-02WAL Series Manual

Hubbell

Hubbell Dual Lite EV Series Manual

Hubbell

Hubbell NXP2 Series Manual de usuario

Hubbell

Hubbell PRS Manual de usuario

Hubbell

Hubbell homeSELECT RMS100 Manual de usuario

Hubbell

Hubbell ExpressLine Miniliter IV MHSY Series Manual de usuario

Hubbell

Hubbell VAPORTITE VBGL Series Manual de usuario

Hubbell

Hubbell Kim Lighting Lightvault LTV59 Manual de usuario

Hubbell

Hubbell VSLT-UP Manual de usuario

Hubbell

Hubbell Compass CU2SO Manual de usuario

Hubbell

Hubbell Laredo LMC Manual de usuario

Hubbell

Hubbell KIM LIGHTING LIGHTVAULT LTV55 Manual de usuario

Hubbell

Hubbell G040 Manual de instrucciones

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario