Huawei EchoLife HG8245 Manual de usuario

Quick Start

EchoLife HG8245 GPON Terminal

Huawei Proprietary and Condential

EchoLife HG8245 GPON Terminal

V100R002C06

Quick Start

Issue 01

Date 2011-06-30

BOM number 31505131

Huawei Technologies Co., Ltd. provides customers with comprehensive technical support.

Please feel free to contact our local ofces or headquarters.

Huawei Technologies Co., Ltd.

Address:

Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Web site: http://www.huawei.com

Tel: 0755-28560000 4008302118

Fax: 0755-28560111

Email: [email protected]

Huawei Proprietary and Condential

No part of this document may be reproduced or transmitted in any form or by any means without

prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their

respective holders.

Notice

The information in this document is subject to change without notice. Unless otherwise stated, this

guide serves only as a guide. All statements, information, and recommendations in this document

do not constitute a warranty of any kind, expressed or implied.

Changes or modications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

Safety Precautions

Basic Requirements

�Keep the device dry when it is stored, transported, and used.

�Prevent any violent collision when the device is stored, transported, and

used.

�Install the device in strict compliance with the requirements of the supplier.

�Do not disassemble the device without permission. In the case of a

device fault, contact the authorized service center.

�Do not change the structure, safety design, or performance design of

the device without prior authorization.

�Observe relevant laws and regulations and respect legal rights of others

when using the device.

Environmental Requirements

�Install the device in a well-ventilated environment that is free from direct

sunlight.

�Keep the device clean and free from dust.

�Keep the device away from water sources or damp areas.

�Do not place any object on the device, so that the device will not be

damaged due to overheating or deformation.

�Reserve a space of at least 10 cm above and around the device for heat

dissipation.

�During the installation, keep the device away from heat sources or

exposed ﬁre sources such as electric heaters and candles.

�During the installation, keep the device away from electric appliances

that generate strong magnetic or electric ﬁelds, such as microwave

ovens, refrigerators, and mobile phones.

Instructions for Cleaning

�Before cleaning the device, stop the device, switch off the power, and

disconnect all cables, including the power cable, optical ﬁber, and

network cable.

�Use a clean, soft, and dry cloth to clean the shell of the device. Do not

use any cleaning agent or spray to clean the shell of the device.

To use the device properly and safely, read the safety precautions carefully before using the

device and strictly observe these precautions when using the device.

Safety Precautions

Instructions for Use

�Use only the accessories delivered or recommended by the supplier, for

example, the power adapter and battery.

�The power supply voltage of the device must meet the requirements for

the input voltage of the device.

�Keep the power plug clean and dry to prevent electric shocks or any

other hazard.

�Dry your hands before connecting or disconnecting cables.

�Stop the device and switch off the power before connecting or

disconnecting cables.

�Switch off the power and disconnect all cables, including the power

cable, optical ﬁber, and network cable, during periods of lightning

activities.

�Switch off the power and then remove the power plug if the device is

to be unused for a long time.

�Prevent water or other liquid from entering the device. If any liquid

enters the device accidentally, immediately switch off the power and

disconnect all cables, including the power cable, optical ﬁber, and

network cable. In the case of a device fault, contact the authorized

service center.

�Do not crush, pull, drag, or excessively bend the cables as doing so may

damage the device and cause the device to malfunction.

�Do not use damaged or deteriorating cables.

�Do not look into the optical port without eye protection.

�If an abnormality occurs, for example, smoke, unusual sound, and smell,

stop the device immediately, switch off the power, disconnect all cables

(such as the power cable, optical cable, and network cable) to the

device, and contact the authorized service center.

�Prevent objects, such as metal, from entering the device through the

heat dissipation hole.

�Do not scratch or abrade the shell of the device. Otherwise, the fallen

coating may lead to device abnormalities (such as short-circuit) and

bodily allergy.

�Keep the device out of the reach of children as the components or

accessories may be swallowed.

�Keep the running device at least 20 cm away from the human body.

Environmental Protection

�Dispose of the device or batteries properly and hand them over to the

certied recycling station.

�Dispose of the packing materials, expired batteries, and old or

abandoned devices in accordance to local laws and regulations

(recycling them is strongly recommended).

After opening the product packaging, check each item against the following checklist.

Contact the supplier if there are any discrepancies.

GPON terminal Power adapter

Quick Start Network cable

Packing List

NOTE

The gures shown in this document may differ from the actual products, but the difference

does not affect the functions of the products.

Product Overview

Appearance and ports of the HG8245

1Optical port 2Ethernet port 3POTS port

4Power switch 5Power port 6Indicator

7Backup battery monitoring port 8USB port 9WLAN switch

10 WPS switch 11 RESET

Installing the GPON Terminal

NOTE

1. HG8245 can be mounted onto a wall or be placed on a workbench.

2. Other installation modes are not allowed.

Perform the following operations to mount HG8245 onto the wall.

Step 1 Mark the positions of two holes, keeping the holes 72 mm from each other.

Step 2 Select a proper drill according to the outer diameter of the screws. Use a

hammer drill to drill the marked positions on the wall. Then clean the wall and

install two expansion bolts.

Step 3 Use a screwdriver to fasten the screws into the expansion bolts, leaving the

heads of the screws 3 mm over the wall. Then install the GPON terminal to the

screws.

Place the GPON terminal on the workbench.

Connecting Cables

Cable Connections Between the HG8245 and Other Devices

1Optical port in the wall 2PC 3IP STB

4TV set 5Phone 6Fax machine

7Power socket 8Backup battery unit 9USB storage device

10 Wi-Fi terminal

Step 1 Use an optical fiber to connect the OPTICAL port on the GPON terminal to

the optical port in the wall.

Step 2 Use a network cable to connect the LAN port to a PC or the Ethernet port on

the IP STB.

Step 3 Use a phone line to connect the TEL port to a phone or fax machine.

Step 4 Use a power adapter to connect the POWER port to the power socket.

Step 5 Use a USB data cable to connect the USB port to the USB storage device.

Step 6 Press the ON/OFF power switch.

Step 7 Press the WLAN switch to enable the Wi-Fi access function. By default, this

function is enabled.

Step 8 Press the WPS switch to enable the WPS encryption function.

NOTE

Connecting Cables

Refer to the preceding cable connections of each product and select the following

corresponding steps to connect the GPON terminal.

NOTE

The optical connector connected to the OPTICAL port on the HG8245 is an SC/APC

connector, and the type of the optical connector connected to the optical port in the

wall is determined by practical conditions.

The preceding figure connects the power adapter as an example. When the backup

battery unit is used, a power monitoring cable is used for connecting the BBU port

to the monitoring port of the backup battery unit. This allows the GPON terminal to

monitor the backup battery unit. For details on how to use the backup battery unit, see

the usage guide to the backup battery.

NOTE

Before enabling the WPS encryption function of a GPON terminal, ensure that the

function is set in the system software in advance. After successful setting, press the

WPS switch for the settings to take effect.

NOTE

The Ethernet port on the HG8245 is a 10/100/1000M Base-T Ethernet port.

Otros manuales para EchoLife HG8245

Tabla de contenidos

Otros manuales de Enrutador de red de Huawei

Huawei

Huawei AR150 series Manual de usuario

Huawei

Huawei Vodafone B970 Manual de usuario

Huawei

Huawei Quidway S9300 Manual de usuario

Huawei

Huawei E5186 Manual de usuario

Huawei

Huawei HG8010 series Manual de usuario

Huawei

Huawei AR Series Manual de funcionamiento

Huawei

Huawei ATN 910C-K Manual de usuario

Huawei

Huawei Quidway S1700-8-AC Manual de usuario

Huawei

Huawei Quidway AR-19-61 Manual de usuario

Huawei

Huawei Flybox 4G Manual de usuario

Huawei

Huawei EG8143A5 Manual de usuario

Huawei

Huawei EchoLife HG8245 Manual de usuario

Huawei

Huawei Quidway S9300 Manual de usuario

Huawei

Huawei 3 Prime Manual de usuario

Huawei

Huawei Quidway S3526 Manual de usuario

Huawei

Huawei Quidway NetEngine80E Manual de usuario

Huawei

Huawei HG232f Manual de usuario

Huawei

Huawei AR530 Series Manual de usuario

Huawei

Huawei SmartAX MT880 Manual de usuario

Huawei

Huawei AR1200 Series Manual de usuario

Huawei

Huawei B818-263 Manual de usuario

Huawei

Huawei Quidway AR 28 Series Manual de usuario

Huawei

Huawei Mobile WiFi E5878 Instrucciones de funcionamiento y mantenimiento

Huawei

Huawei AR150/200 Series Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad