Huawei EG8010H Manual de usuario
EG8010H
Quick Start for QR code
Issue 04
Date 2020-07-21
HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specied in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every eort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: https://www.huawei.com
Email: [email protected]
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. i
Contents
1 Placing the Device................................................................................................................... 1
2 Connecting Cables................................................................................................................... 3
3 Indicator Description.............................................................................................................. 5
4 Technical Specications......................................................................................................... 7
5 FAQs............................................................................................................................................ 8
EG8010H
Quick Start for QR code Contents
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. ii
1 Placing the Device
NO TE
● Do not install the ONT outdoors or in an outdoor cabinet.
● The ONT can be mounted onto a wall or placed on a desk. Do not install the ONT in
other modes, such as ceiling.
● Keep 10 cm clearance on all sides to ensure adequate ventilation.
● It is recommended that the computer and ONT be put far away from electric appliances
that generate strong magnetic or electric elds, such as microwave ovens.
Mounting an ONT on the desk
The gure below shows an ONT that is horizontally placed on a desk.
NO TE
The appearance shown in this document may be dierent from the actual appearance of
the product. The actual product prevails.
EG8010H
Quick Start for QR code 1 Placing the Device
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 1
Mounting an ONT onto the wall
1. Mark two positions with the same spacing as that between the two mounting
holes of the ONT using a marker on a wall.
2. Select a proper drill bit according to the outer diameter of the screws. Use a
hammer drill to drill the marked positions on the wall. Then clean the holes
and install two expansion bolts.
3. Use a screwdriver to fasten the screws into the expansion bolts, reserving 5
mm ends out of the wall, and mount the ONT onto the screws.
NO TE
It is recommended that the screw be about 4 mm in diameter and longer than 20 mm.
EG8010H
Quick Start for QR code 1 Placing the Device
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 2
2 Connecting Cables
EG8010H
Quick Start for QR code 2 Connecting Cables
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 3
NO TE
● The ber connector connected to the optical port on the wall varies depending on
actual conditions.
● To ensure normal use of bers, make sure that the ber bending radius is larger than 30
mm.
No. Item Description
1 ON/OFF Powers the ONT on or o.
2 POWER Connects to a power adapter.
3 LAN Connects to PC or IP set-top box (STB).
4 OPTICAL The optical port is equipped with a rubber plug and
connected to a ber for upstream transmission.
The type of the optical connector connected to the
optical port can be SC/APC.
5 Reset Press the button for a short time to reset the device; or
press the button for a long time (longer than 10s) to
restore the device to the default settings and reset the
device.
NOTE
Reset Huawei ONTs with caution. Otherwise, the ONTs may fail
to access the Internet. If an ONT cannot access the Internet
after a reset, contact your Internet service provider.
EG8010H
Quick Start for QR code 2 Connecting Cables
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 4
3 Indicator Description
Indicator Status Description
POWER Steady on The ONT is powered on.
O The power supply is cut o.
PON/LOS See the following table.
LAN Steady on The Ethernet connection is in the normal state.
Blinking Data is being transmitted over the Ethernet port.
O The Ethernet connection is not set up.
Status
No.
PON Status LOS Status Description
1O O The ONT is prohibited by the upper-
layer device or blinks abnormally.
Contact the service provider for help.
2 Blinks twice
a second
Blinks twice a
second
3 Blinks twice
a second
O The ONT attempts to set up a
connection with its upper-layer
device.
4 Steady on O A connection is set up between the
ONT and its upper-layer device.
EG8010H
Quick Start for QR code 3 Indicator Description
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 5
Status
No.
PON Status LOS Status Description
5O Blinks once
every 2
seconds
The ONT is not connected to bers
or does not receive optical signals.
6 Blinks once
every 2
seconds
Blinks once
every 2
seconds
The hardware is faulty.
EG8010H
Quick Start for QR code 3 Indicator Description
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 6
4 Technical Specications
Product Function
EG8010H 1 Ethernet port
● Power adapter input: See the nameplate on the adapter.
● System power supply: See the nameplate on the device.
● Ambient temperature: 0ºC to +40ºC
● Ambient humidity: 5%–95% (non-condensing)
● Dimensions (H x W x D): 28 mm x 69 mm x 83 mm
● Weight: About 70g
● Maximum system power consumption: 6 W
EG8010H
Quick Start for QR code 4 Technical Specications
Issue 04 (2020-07-21) Copyright © Huawei Technologies Co., Ltd. 7
Tabla de contenidos
Otros manuales de Hardware de red de Huawei
Huawei
Huawei FusionModule1000A40 ICT Solution Manual de funcionamiento
Huawei
Huawei Airbridge DBS3900 Guía
Huawei
Huawei CR52-LPUF-20 Manual de usuario
Huawei
Huawei NE-FIC-STM1/ATM-MM/1310 Manual de usuario
Huawei
Huawei CR52-10GE Manual de usuario
Huawei
Huawei eSight V200R003C00 Manual
Huawei
Huawei CR52-POS/STM64 Manual de usuario
Huawei
Huawei 21501043-003 Manual de usuario
Huawei
Huawei FusionModule 500 Manual de usuario
Huawei
Huawei OptiXstar P612E Manual de usuario
Huawei
Huawei PDU8000 Series Manual de usuario
Huawei
Huawei OptiXstar V183 Manual de usuario
Huawei
Huawei MAP05A1 Manual de usuario
Huawei
Huawei ME60 Series Guía
Huawei
Huawei CR52-4xPOS/STM1-SFP Manual de usuario
Huawei
Huawei eAN3810A Guía de referencia rápida
Huawei
Huawei E5785-320a Especificaciones técnicas
Huawei
Huawei CR-R1UL Manual de usuario
Huawei
Huawei FIC-1/2ADSL Manual de usuario
Huawei
Huawei SUN2000-8K-LC0 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
