Huawei OptiX RTN PI-DC B10 Instrucciones de funcionamiento y seguridad

OptiX RTN PI-DC B10

Product Overview and Quick Installation Guide

Safety Precautions

•The equipment that collect to the GE electrical port must have surge protection capabilities. If the equipment does not

have surge protection capabilities, the PIs should be installed indoors for surge protection and easy maintenance.

•Always hold an insulated part of the P&E cable. Never touch the RJ45 connector.

•Do not touch the pins inside the P&E port on the PI with your hands or a conductor.

•Be sure to connect the power cables of the PI correctly tothe positive and negative terminals of the power supply

device .To prevent damage to power cables or devices caused by short-circuits, install a circuit breaker on the

negative terminal of the power supply device.

•Do not install or remove a live P&E cable.

Issue:05

Date: 2018-10-30

Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base

Bantian, Longgang

Shenzhen 518129

People's Republic of China

Website: http://www.huawei.com

Email: support@huawei.com

No part of this document may be reproduced or transmitted in any form or by any means without prior

written consent of Huawei Technologies Co., Ltd.

HUAWEI TECHNOLOGIES CO., LTD .

AAppearance and Ports

The RTN PI-DC B10 is a full-outdoor PI. It uses DC powerinput and transmits GE electrical signals and -48 V power signals to the full-outdoor RTN 300 equipment through an outdoor network

cable.

ProductOverview

CIndicator Status Description

Indicator Status Meaning

DC IN Steady green Power is supplied.

Off Power is not supplied.

P&E OUT

Steady green Power over Ethernet is being output

normally.

Off Power over Ethernet is not being output.

BPort Description

The GE electrical port is compatible with an FE electrical port and supports the MDI, MDI-X, and auto-

MDI/MDI-X modes.

Pin Description

1 BGND

2 BGND

3 -48 V power signal

4 BGND

5 BGND

6 -48 V power signal

7 -48 V power signal

8 -48 V power signal

Whetherthe P&E ports useMDI or MDI-X modeto transmitEthernet servicesignals does not affect the

pin assignments forpower signals.

Pin assignments for power signals in the P&E ports

(1) (2) (3)

(5) (6) (7) (8)

(9)

(10)

(4)

(11)

(12)

(13)

Mounting ears

Cover of the PI(1)

P&E cable (PI-side), pin assignments of the P&E

RJ45 connector and MGMT RJ45 connector

(2)

1:2 peeling indicator for P&E cables, DC cables,

and GE/NMS cables

(3)

(4) See "Safety Precautions“.

GE electrical port (to FE/GE UNI equipment)

(5)

P&E port connected to a

P&E cable)

(6)

MGMT port connected to a P&E cable

(7)

DC power port connected to the power supply device)

(9)

DC input and P&E output status indicator

(10)

Plug

(11)

Cable hole

(12)

(8) NMS port connected to the NMS

(13) Wire clip

Principles and Application Scenarios

ProductOverview

The RTN PI-DC B10 receives one channel of DC power signals and one channel of GE service signals.

The signal coupling module couples DC power signals and GE service signals into P&E signals and outputs the P&E signals

to the P&E port.

The frequencies of DC power signals and GE service signals do not interfere with each other. Therefore, the two types of

signals can be transmitted over the same twisted pair.

DC-DC

processing

mode

DC IN

Signal

coupling

module

GE P&E

DC-PI working principles

DC-PI

powered

device

UNI-side

device

≤ 100 m

•The PI onlycouples GEsignals and powersignals,butdoes notregenerateorstrengthenGE signals.Therefore,the

networkcablebetweenthe UNI-sidedeviceandthe powered device mustnotbe longerthan100 m.

•The maximum distancebetween thePI andthe powereddevicevaries dependingonthepowerof the powereddevice.

For details,seetechnical specifications.

Maximum

distance between

the PI and

powered device

CAUTION

BApplication Scenarios

APrinciples

Mapping between powered device types and power supply modes

Device Type Version PI Support (Yes/No)

RTN 310 (Integrated)

SHXA2 board

Yes

SXA3 board

Yes

RTN 310

(Split) Yes

RTN 320 (Integrated)

RTN 320 (Split)

RTN 320F

RTN 360 (V

-band) Yes

RTN 380 (E

-band)

SHUF3 board

Yes

MXUF4 board

Yes

RTN 380e

Yes

RTN 380A

Yes

RTN 380AX

RTN 380H

MXUI5 board

MXXI5 board

Technical Specifications

ProductOverview

APower Supply

Item Description

Input voltage DC input, with the voltage ranging from –38.4 V to –57.6 V

Input power cable diameter 2.5 mm2

Output voltage mode P&E output

P&E output

mode

Number of power

output channels 1

Output power Output power ≤ 80 W

Distance between the

PI and powered

device

Shorter than or equal to 100 m

Item Description

Electromagnetic compatibility •Passed CE authentication.

Safety •Passes CE certification.

•Compliant with IEC 60950-22.

•Compliant with EN 60950-22.

Item Description

Major reference standards

Operation Compliant with ETSI EN 300 019-1-3 cl ass 3.2.

Transportation Compli ant with ETSI EN 300 019-1-2 class 2.3.

Storage Compliant with ETSI EN 300 019-1-1 class 1.2.

Operating temperature -33°C to +55°C

Relative humidity 10% to 100%

Earthquake resistance Compliant with ETSI 300 019-2-4

Altitude 4500 m (14,764 ft), Compliant with ETSI

300 019

Protection class IP65

Item Description

Dimensions (H x W x D) 226 mm x 164 mm x 43.6 mm

Weight 1.3 kg

BDimensions and Weight

CElectromagnetic Compatibility and Safety Compliance

DDeployment Environment

Installation Reference

1Open the cover of the PI.

Loosen thescrews onthecover andopenthe

cover (4.8±0.48N·M). Removethe plugs inthe cableholes thatwill holdcables.

Reserve the plugs in the unused cable holes.

2Install PI cables.

For the peeling sizes of cables, see the 1:2 peeling

indicator on the PI.

Avoid dropping any metal scraps or other miscellaneous

objects on the front panel or in any ports or cracks in the PI.

MGMT

P&E

(+)(-)

Open the covers the power ports.

Install the power cables with OT

terminals to the power ports.

Ensure that the positive and

negative cables are correctly

connected.

Tighten the screws of the OT terminals.

Close the covers of the power ports.

Black (brown): 0 V

ground cable

Blue: -48 V

Power

supply

device

Connectedto oneFE/GE

(electrical)service

Wire clip

Connectedto the P&E

port of the equipment

Wire clip

Peela cableaccording to the 1:2 peelingindicator

andexposethe shieldlayer.

Loosenawireclip.

Routethe cablethrough the rubberring andwire clip

andfix the cableinthe waterproofcabletrough.

Tightenthe wire clipandensure that the wire clipis

completelypressedagainsttheshieldlayerwithno

contact of the sheath. The shieldlayeris not

exposed.

The peeling sizeis largerthanthe 1:2 peeling

indicatorandthe exposedshieldlayerextends to

the waterproofcabletrough, whichfails the

waterprooffunction.

The cableis not fixed

with a wireclip.

Shield layer

of a cable

The shield layers of all PI cables must be grounded using wire clips. Otherwise, the cables may be

damaged by lightning strikes.

02/03>>

•If an 8-coreP&E cableis used to

connectan outdoordevice to a PI,

connectthe P&E cable to the P&E

port on the PI.

•If a 12-coreP&E cable is usedto

connectan outdoordevice to a PI,

connectthe 8-core connectorof the

cableto the P&E port onthe PI and

the 4-coreconnectorof the cableto

the MGMT port on the PI.

Installation Reference

Close the cover of the PI and tighten all screws on the cover.

•Follow the order from 1 to 8 when you tighten the

screws.

•Tighten all screws on the cover (4.8±0.48 N·M).

Optional: Install the PI on a wall.

Mark and drill holes in the wall.

Hold the PI up to the wallandmark the drilling positions. Drill the holes and insertthe fixingbolts. If multiple PIs need to be installed, reserveaheat

dissipation spaceof atleast 50 mm aroundeachPI.

Drilling

positions

Drill Ф8 holes to a depth of 52 to 60 mm.

Mounting holes

Install the PI on the wall.

•Hold the PI whenyou fix it on a wall.The PI willdrop off without

enoughsupport.

•Ensurethat the serviceports of the PI face downwardbefore

you fix the PI.

04/05>> 06

Installation Reference

Down

Optional: Install the PI on a pole or a tower.

Guidea hoseclampthroughtheholes andfix the hoseclamponthe poleor tower.

Holes forinstallinga hoseclamp

Holes forinstallinga hoseclampThe

di ameter of the pole i s 48 mm to 114 mm.

Tighten the screws on the hose clamp.

Install the other hose clamp by repeating the previous steps.

•Holdthe PI whenyou fix it on a poleor a tower. The PI willdrop

off withoutenough support.

•Ensurethat the serviceports of the PI face downward before

you fix the PI.

Install the PGND cable of the PI.

Connectthe OT terminalofthe PGND

cableto the ground nut.

PGND cable

Removethe anticorrosionpaintandoxidelayer at the ground

point. After the connection is complete,waterproofand

rustproofthe groundpoint.

Installthe base of

ground clip.

After the PGND cable is installed,applyanti-seizegrease to

the ground nut and ground point.

06/07>> 07

The diameter of the pole

is 48 mm to 114 mm.

Tabla de contenidos

Otros manuales de Hardware de red de Huawei

Huawei

Huawei RT-FIC-4SAE Manual de usuario

Huawei

Huawei CR52-2xPOS/STM16-SFP Manual de usuario

Huawei

Huawei PowerCube 500 V200R001C10 Manual de usuario

Huawei

Huawei LSBM1FP20B0 Manual de usuario

Huawei

Huawei SmartAX MA5608T Manual de usuario

Huawei

Huawei NE-HIC-2xFE Manual de usuario

Huawei

Huawei UPS2000-A-6KTTL Manual de usuario

Huawei

Huawei RAN14.0 Especificaciones técnicas

Huawei

Huawei 21501043-003 Manual de usuario

Huawei

Huawei SUN2000 Series Manual de usuario

Huawei

Huawei CR52-MPUA Manual de usuario

Huawei

Huawei NE-FIC-CE3 Manual de usuario

Huawei

Huawei CR52-2xPOS/STM16-SFP Manual de usuario

Huawei

Huawei FusionModule2000 V500R003C10 Especificaciones técnicas

Huawei

Huawei LUNA2000-97KWH-1H1 Manual de usuario

Huawei

Huawei CR52K-10GE Manual de usuario

Huawei

Huawei RTN 380e V100R007 Manual de usuario

Huawei

Huawei VP9650 Especificaciones técnicas

Huawei

Huawei SmartLi 1.0 Manual de usuario

Huawei

Huawei OptiX OSN 3500 Instrucciones de uso

Huawei

Huawei FusionServer Pro CH121 V5 V100R005 Manual

Huawei

Huawei EN83CTLA Manual de usuario

Huawei

Huawei eSight V200R003C00 Manual

Huawei

Huawei EchoLife HG8245 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario