Huawei V100R001C00 Manual de usuario

HUAWEI Micro DC V100R001C00

Quick Installation Guide

Issue: 01

BOM: 31505829

Release Date: 2013-03-06

This document helps the customer service personnel quickly install the Micro data center (DC). For details, see the product

document CD-ROM delivered with the product.

Required Tools

Installation Process

Devices delivered to customers consist of typical configuration suite and extension components. The installation of extension

components varies with the number of terminals to be supported, while the installation of the typical configuration suite remains

unchanged. The Micro DC applies to scenarios in which 150, 300, and 600 terminals are supported.

If customers require more than 1 hour backup power, install a battery cabinet.

Cabinet installation process for 150 terminals Cabinet installation process for 300 and 600 terminals

Checking Quantities and Types of Goods

Checking Quantities and Types of Goods > Inspecting Goods

Inspecting the battery pack Inspecting the monitoring suite outside the cabinet

If there are other components that require inspections, unpack and inspect them.

Number of

terminals

Device Type Device Quantity Remarks

Micro DC All-in-One cabinet 1

1 AR2220, 1 S5752, 3 S3752s, 1 PDB, 1 UPS (6 kVA), 1 PDU, 1

fan assembly, and 1 monitoring system (including 1 ECC, 1

temperature and humidity sensor, 1 water leakage sensor, 2 door

status sensors, and 1 smoke sensor)

Basic/Storage/Computing RH2288 1

Battery pack 3

Monitoring suite outside the

cabinet (including the sensor

mounting arm, smoke sensor, and

IP camera)

AP6010DN 2

Micro DC All-in-One cabinet 1

1AR2220, 1 S5752, 1 PDB, 1 UPS (6 kVA), 1 PDU, 1 fan assembly, and 1

monitoring system (including 1 ECC, 1 temperature and humidity sensor, 1

water leakage sensor, 2 door status sensors, and 1 smoke sensor)

Basic/Storage/Computing RH2288 1

Battery pack 3

Monitoring suite outside the

cabinet (including the sensor

mounting arm, smoke sensor, and

IP camera)

AP6010DN 3

Network distribution cabinet 1

S3752 (office edition) 8

Micro DC All-in-One cabinet 1

1AR2240, 1 S5752, 1 PDB, 1 UPS (6 kVA), 1 PDU, 1 fan assembly, and 1

monitoring system (including 1 ECC, 1 temperature and humidity sensor, 1

water leakage sensor, 2 door status sensors, and 1 smoke sensor)

Basic/Storage/Computing RH2288 1

Battery pack 3

Monitoring suite outside the

cabinet (including the sensor

mounting arm, smoke sensor, and

IP camera)

AP6010DN 4

Basic RH2288 1

Network distribution cabinet 1

S3752 (office edition) 12

600

Typical

configuratio

n suite

Extension

components

150

Typical

configuratio

n suite

Extension

components

300

Typical

configuratio

n suite

Extension

components

Use a screwdriver to

loosen the wooden

screw.

Installation Planning

For 150 terminals

All-in-One cabinet

Installation Planning

For 300 terminals

All-in-One cabinet

42 1U 1U 42

41 1U 1U 41

40 1U 1U 40

39 1U 1U 39

38 1U 1U 38

37 1U 1U 37

36 1U 1U 36

35 1U 1U 35

34 1U 1U 34

33 1U 1U 33

32 1U 1U 32

31 1U 1U 31

30 1U 1U 30

29 1U 1U 29

28 1U 1U 28

27 1U 1U 27

26 1U 1U 26

25 1U 1U 25

24 1U 1U 24

23 1U 1U 23

22 1U 1U 22

21 1U 1U 21

20 1U 1U 20

19 1U 1U 19

18 1U 1U 18

17 1U 1U 17

16 1U 1U 16

15 1U 1U 15

14 1U 1U 14

13 1U 1U 13

12 1U 1U 12

11 1U 1U 11

10 1U 1U 10

91U 1U 9

81U 1U 8

71U 1U 7

61U 1U 6

51U 1U 5

41U 1U 4

31U 1U 3

21U 1U 2

11U 1U 1

Network distribution

cabinet (front view)

S3752 switch

Network distribution

cabinet (front view)

Installation Planning

For 600 terminals

All-in-One cabinet

42 1U 1U 42

41 1U 1U 41

40 1U 1U 40

39 1U 1U 39

38 1U 1U 38

37 1U 1U 37

36 1U 1U 36

35 1U 1U 35

34 1U 1U 34

33 1U 1U 33

32 1U 1U 32

31 1U 1U 31

30 1U 1U 30

29 1U 1U 29

28 1U 1U 28

27 1U 1U 27

26 1U 1U 26

25 1U 1U 25

24 1U 1U 24

23 1U 1U 23

22 1U 1U 22

21 1U 1U 21

20 1U 1U 20

19 1U 1U 19

18 1U 1U 18

17 1U 1U 17

16 1U 1U 16

15 1U 1U 15

14 1U 1U 14

13 1U 1U 13

12 1U 1U 12

11 1U 1U 11

10 1U 1U 10

91U 1U 9

81U 1U 8

71U 1U 7

61U 1U 6

51U 1U 5

41U 1U 4

31U 1U 3

21U 1U 2

11U 1U 1

Network distribution

cabinet (front view)

S3752 switch

Network distribution

cabinet (front view)

Labeling for Network Devices

Labeling

Labeling for Power Cables

On the PDU end

On the device end

If there are multiple power modules that are not

numbered in a device, number them in an

ascending order from the top down and from left

to right.

Only one power distribution unit (PDU) is

preinstalled in the All-in-One cabinet and

numbered PDU1.

More PDUs are numbered in an ascending

order from outside to inside and from left to

right.

The rack is divided into 42 U (1 U = 1.75 in.),

numbering from 1 to 42 from the bottom up.

For the network device occupying more than 1 U,

the label records the smallest height number. For

example, if a 2 U network device occupies 34 U

and 35 U, "34U" will be present in the label.

Checking Quantities and Types of Goods > Inspecting Goods > Installing the Typical Configuration

Suite > Installing the All-in-One cabinet (for All Scenarios)

1 2

Remove reinforcing brackets from

the cabinet.

Install the ground cable.

Prepare the power cable connectors.

Connect power cables.

Combine and level cabinets.

There is one reinforcing

bracket at the height of 22 U

(38.5 in.) in the front and rear

of the cabinet. Before

removing the front reinforcing

bracket, remove the filler

panels at the height of 23 U to

25 U (40.25 in. to 43.75 in.).

Mains inlet port

Power cable

Ground cable

Checking Quantities and Types of Goods > Inspecting Goods > Installing the Typical Configuration Suite

> Installing the All-in-One Cabinet > (Optional) Installing the SIM Card (for All Scenarios)

Remove the General Packet Radio Service

(GPRS) module from the ECC.

Install the subscriber identity module (SIM)

card.

SIM card slot

GPRS module

ECC

Lead the cable from the GPRS antenna into the cabinet

through the cable hole on the top of the cabinet. Route the

cable along the external side of the mounting bar on the

right of the rear of the cabinet to the ECC at the cabinet

bottom. Then bind the cable to the cable tray under the ECC.

Checking Quantities and Types of Goods > Inspecting Goods > Installing the Typical Configuration Suite

> Installing the All-in-One cabinet > Installing the GPRS Antenna (for All Scenarios)

Loosen screws beside the GPRS module

and pull out the module.

Checking Quantities and Types of Goods > Inspecting Goods > Installing the Typical Configuration

Suite > (Optional) Installing Battery Packs (for All Scenarios)

If customers require more than 1 hour backup power,

install a battery cabinet or battery packs.

Before connecting battery packs using power

cables, loosen screws beside the protection cover

for the wiring terminals and remove the

protection cover.

Install the protection cover after connecting

battery packs using power cables.

Positions for installing Battery Packs

Checking Quantities and Types of Goods > Inspecting Goods > Installing the Typical Configuration

Suite > Installing Servers (for All Scenarios)

Only one RH2288 is provided by default for Micro DC typical configurations for 150, 300, and 600 terminals.

The All-in-One cabinet reserves space for another two servers. Customers can install two more servers if one RH2288 cannot meet

requirements.

If three RH2288 servers are installed, number them RH2288_1, RH2288_2, and RH2288_3.

Install the servers in the right place.

No ground cable is required, because the RH2288 is

configured with AC power modules.

Server installation

Network cable connection for a server Network cable connection for two servers

Positions for installing servers

Power ground cable connection

Tabla de contenidos

Otros manuales de Unidad de control de Huawei

Huawei

Huawei PDU5000 Manual de usuario

Huawei

Huawei MU203 Manual de usuario

Huawei

Huawei MU609 Instrucciones de instalación

Huawei

Huawei ME909s-120 Instrucciones de instalación

Huawei

Huawei UPS5000-E-400K-SMS Manual de usuario

Huawei

Huawei Atool Manual de usuario

Huawei

Huawei MU709 Series Instrucciones de instalación

Huawei

Huawei RTN 380H Manual de usuario

Huawei

Huawei ME906A Instrucciones de montaje

Huawei

Huawei UPS5000-E-200K-SM Manual de usuario

Huawei

Huawei ME309-562 Instrucciones de instalación

Huawei

Huawei EM820W Instrucciones de instalación

Huawei

Huawei RMS-SNMP01A Manual de usuario

Huawei

Huawei MU736 HSPA+ M.2 Guía del usuario

Huawei

Huawei EM775 Manual de usuario

Huawei

Huawei ATOM GPS Manual de usuario

Huawei

Huawei UPS5000-H-400K-NT Manual de usuario

Huawei

Huawei MU509-65 Instrucciones de instalación

Huawei

Huawei UPS5000-E Series Manual de usuario

Huawei

Huawei ME909s Series Instrucciones de instalación

Huawei

Huawei MU509 Series Instrucciones de instalación

Huawei

Huawei UPS5000-E Series Manual de usuario

Huawei

Huawei ME906E Manual de usuario

Huawei

Huawei ME906V Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario