Huawei PDU5000 Manual de usuario
HUAWEI TECHNOLOGIES CO., LTD.
PDU5000
Quick Guide
Parts No.:02121671
Issue:01
Date:2019-01-10
1Safety Precautions
1. General safety precautions
To ensure human safety and equipment security, pay attention to all the precautions marked on the
equipment and instructed in the product documentation.
The "NOTICE", "CAUTION", "WARNING", and "DANGER" statements in this document do not
represent all the safety instructions. They are only supplements to the safety instructions.
2. Local laws and regulations
Comply with local laws and regulations when operating the equipment. The safety instructions in
the document are only supplements to the local laws and regulations.
3. Personnel requirements
Personnel who plan to install or maintain Huawei equipment must receive a thorough training,
understand all necessary safety precautions, and be able to perform all operations correctly.
•Only trained and qualified personnel are allowed to install, operate, and maintain the equipment.
•Only personnel certified or authorized by Huawei are allowed to replace or change the equipment
or components (including software).
•Any fault or error that might cause safety problems must be reported immediately to a supervisor.
4. Grounding requirements
•When installing the equipment, ground it first.
•When removing the equipment, disconnect the ground cable finally.
•Do not damage the ground conductor.
•Do not operate the equipment in the absence of a properly installed ground conductor.
•The equipment must be grounded permanently. Before operating the equipment, check the
electrical connection of the equipment to ensure that it is securely grounded.
5. Personal requirements
•Do not operate the equipment or cables during thunderstorms.
•Remove the AC power connector and do not use the fixed terminal or touch the terminal or
antenna connector in a thunderstorm.
•Before operating the equipment, wear electrostatic discharge (ESD) clothes, ESD gloves, and an
ESD wrist strap. Do not wear conductors such as jewelry or watches when operating the
equipment.
•In the case of a fire, immediately leave the building or the equipment area, and turn on the fire
alarm bell or make an emergency call. Never enter a building or equipment area that is on fire.
6. Equipment requirements
•Before operations, ensure that the equipment is firmly secured to the floor or other solid objects,
such as a wall or an installation rack.
•Do not block the air vent while the system is operating.
•Tighten the screws using tools when installing panels.
•After installation, remove the packing materials from the equipment area.
1
2Overview
2
No.
Component Name
No.
Component Name
1
AC input
circuit breaker
2
Surge protective device (SPD)
switch
3
SPD
4
AC output circuit breaker
5
AC output terminal block
6
AC input terminal block
7
PE
N/
A
N/A
1. Appearance dimensions of the PDU5000.
2. Feature Introduction of the PDU5000.
1 2 34
5 6 7
Front view of the PDU5000
Back view of the PDU5000
430
630
664
482.6
130
Front
Back
Unit: mm
3
•Unpack the equipment and visually inspect its appearance to check whether the equipment is
paint-peeling, misshapen, scratched, or soaked. If so, record the information and contact the
equipment carrier and the local Huawei office immediately.
•Check against the packing list that the equipment and components are correct and complete. If
some components are missing or do not conform to the packing list, record the information and
contact Huawei or the local Huawei office immediately.
3Unpacking and Acceptance
Installing PDU5000 Cables
4
1. Elementary diagram of the PDU5000.
2. Install cables for the PDU5000 by referring to the following figure.
S201-D63A/1P
1QF
FS/20K A
QF2
C32A/1P
QF3
C32A/1P
QF4
C32A/1P
QF5
C32A/1P
QF6
C32A/1P
QF7
B10A/2 PRCD
QF8
B10A/2 PRCD
QF9
B10A/1 P
QF10
B10A/1 P
QF11
B10A/1 P
QFS
C32A/2P
QF1
C32A/1P RVVZ-3x6
RVVZ-3x6
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
RVVZ-3x1.0
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
L,N,PE
AC Input
AC Output
EquipmentroomPE
InputPE OutputPE
4
No.
Check Item
Check Result
1
All cables are correctly connected based on the Schematic Diagram.
□
Passed □Failed
2
Ground cables are securely connected.
□
Passed □Failed
3
Redundant parts of the ground cables and power cables are cut off
instead of coiled.
□
Passed □Failed
4
Power cables and ground cables are routed and bundled separately from
other types of cables.
□
Passed □Failed
5
All circuit breakers are OFF.
□
Passed □Failed
6
The appearance is intact without any damage.
□
Passed □Failed
7
All labels are correct, clear, and complete.
□
Passed □Failed
8
The surrounding area of the cabinet contains no waste tape, cable ties,
paper, or packing materials.
□
Passed □Failed
9
All bolts are tightened, especially the bolts used for electrical connection.
Flat washers and spring washers are installed properly in the correct
sequence.
□
Passed □Failed
10
Cables are bundled neatly, and cable ties are secured evenly and
properly in the same direction.
□
Passed □Failed
11
Cables are routed for ease of future maintenance and expansion.
□
Passed □Failed
12
There is no unnecessary adhesive tape or cable tie on the cables.
□
Passed □Failed
13
Exposed parts near the wiring terminals and lugs are wrapped in PVC
insulation tape or heat shrinking tubing.
□
Passed □Failed
14
Flat and spring washers are properly installed on each bolt of a wiring
terminal.
□
Passed □Failed
15
The power and signal cables are routed in accordance with the weak
-
and strong
-
current cable routing specifications and the cable routing plan.
□
Passed □Failed
Check Before Power-On
5
1. Turn on the SPD circuit breaker.
2. Turn on the external power input circuit breaker.
3. Turn on the input switch.
4. Turn on all output circuit breakers of the PDU5000 in sequence and check that the output voltage
is normal by using a multimeter.
5. After checking that the parameters are normal, turn off all the circuit breakers one by one and
disconnect the power supply.
Power-On Commissioning
6
When switching on the circuit breakers, observe whether there is any abnormal phenomenon, such
as sparks or unsmooth switching on/off.
NOTE
5
Item
Interval
Operation
Guide
Reference Standard
Troubleshooting
Connections of
input and output
power cables
Monthly
Visual
observation
1.
The cables are not
damaged.
2. The terminals are intact,
secure, and free from
spark signs and rust.
Take measures
depending on the severity.
Appearance of
power distribution
components
Quarterly
Visual
observation
The appearance is intact.
Take measures
depending on the severity.
Operating
temperature and
humidity
Quarterly
Measure the
temperature
and humidity
using a point
thermometer.
Operating temperature:
–
5
°C to +40°C
Relative humidity: 5%
–
95% RH
Check that the air
conditioner and
dehumidifier in the
equipment room function
properly.
Dust on the
surface of the
PDU5000
Yearly
Check
whether there
is dust.
The white paper that you
use to wipe the equipment
is clean.
If the white paper is dirty,
clean the PDU5000.
Routine Maintenance
7
Symptom
Possible Causes
Troubleshooting Measures
The surge
protection function
fails.
•
The SPD circuit breaker is
not turned on.
•
The SPD ground cable is
not connected.
•
The surge protection
module is abnormal. The
SPD window is red.
•
Check that the SPD circuit breaker is turned
on.
•Check that the SPD ground cable is connected.
•
Replace the surge protection module.
The rear
-end
device power input
is abnormal.
•The switch trips abnormally.
•
The PDU5000 is faulty.
•
Use a multimeter to check whether there is a
short circuit. Turn on the switch again, and
check whether the system is overloaded.
•
Restart the PDU5000. If the PDU5000
is faulty,
replace it.
The PDU5000
does not report
faults, but has no
output voltage.
•
The output power cable is
not securely connected.
•
The output circuit breaker
is abnormal.
•
Check the output power cable connection.
•
Replace the circuit breaker.
Troubleshooting
8
6
Technical Specifications
9
Item
Specifications
Operating temperature –5°C to +40°C
Storage temperature –40°C to +70°C
Relative humidity 5%–95% RH (non-condensing)
Altitude ≤ 2000 m
Rated operating frequency 50 Hz
Rated operating voltage 220 V AC
Installation mode Installed inside a cabinet
Protection level IP20
Huawei Technologies Co., Ltd.
Huawei Industrial Base, Bantian, Longgang
Shenzhen 518129 People's Republic of China
www.huawei.com
Tabla de contenidos
Otros manuales de Unidad de control de Huawei
Huawei
Huawei MG323 Manual de usuario
Huawei
Huawei ME936 Instrucciones de instalación
Huawei
Huawei ME909u-521 Instrucciones de instalación
Huawei
Huawei CX320 Manual de usuario
Huawei
Huawei MU203 Manual de usuario
Huawei
Huawei ME906A Instrucciones de montaje
Huawei
Huawei MU709 Series Instrucciones de instalación
Huawei
Huawei G530 V2 Guía de referencia rápida
Huawei
Huawei MU509 Series Manual de usuario
Huawei
Huawei EM770 Manual de usuario
Huawei
Huawei SmartAX MA5675 Manual de usuario
Huawei
Huawei ME909s-120 Instrucciones de instalación
Huawei
Huawei UPS5000-E Series Manual de usuario
Huawei
Huawei RTN 380H Manual de usuario
Huawei
Huawei RMS-SNMP01A Manual de usuario
Huawei
Huawei UPS5000-E Series Manual de usuario
Huawei
Huawei ME909u-523 Guía del usuario
Huawei
Huawei Atool Manual de usuario
Huawei
Huawei MU509-65 Instrucciones de instalación
Huawei
Huawei ME936 Instrucciones de instalación
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
