HP Xw6600 - Workstation - 2 GB RAM Manual de usuario

Small form factor bay converter and hard

drive installation

HP xw6600 and HP xw8600 Workstations

This document describes how to convert HP xw6600 and HP xw8600 Workstation 3.5-inch hard drive

bays to hold small form factor (SFF) hard drives. The HP xw6600 Workstation can accept one SFF bay

converter carrier and up to three SFF hard drives. The HP xw8600 Workstation can accept two SFF bay

converter carriers and up to six SFF hard drives.

Kit contents

HP SFF 2.5-inch SAS hard drive kit

2.5-inch SAS hard drive

SAS-to-SATA connector adapter

Assorted SATA data cables

Warranty

Product documentation

HP 2.5-inch SFF 2:3 Bay Converter kit

2.5-inch SFF hard drive carrier

Adapter power cable

Product documentation

trademark of Hewlett-Packard Development Company, L.P. Printed in the U.S.

ENWW HP xw6600 and HP xw8600 Workstations 1

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce

the risk of injury from a hot component, enable the surface to cool before touching.

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed

area marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper

workstation setup, posture, health, and work habits for computer users, and provides important electrical

and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the

documentation CD (if one is included with the product).

WARNING! If a product is shipped in packaging marked with this symbol, , the product must always

be lifted by two persons to avoid personal injury due to product weight.

CAUTION: Static electricity can damage the electronic components of the workstation. Before

beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal

object.

CAUTION: Observe the following cautions when removing or replacing a processor:

— Installing a processor incorrectly can damage the system board. Contact an HP authorized reseller

or service provider to install the processor. If you plan to install the processor yourself, read all of the

instructions carefully before you begin.

— Failure to follow the workstation preparation instructions can result in an improperly installed

processor, causing extensive workstation damage.

— Processor socket pins are delicate and bend easily. Use extreme care when placing the processor

in the socket.

2 Small form factor bay converter and hard drive installation ENWW

CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge

(ESD) precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body

to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat,

static strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested

for reliability and are manufactured to high quality standards.

ENWW Warnings and cautions 3

System requirements

●HP xw6600 Workstation. Optional HP SAS RAID card kit (or equivalent) must be installed and

have one unused SAS port connector for each SFF SAS hard drive being installed.

●HP xw8600 Workstation. One unused HP SAS or SAS RAID card port connector for each SAS

SFF hard drive being installed.

Tools required

No tools are required for this assembly.

Step 1–Preparing the workstation

Detailed instructions for preparing the workstation for component installation are contained in your

workstation documentation.

In summary, to prepare your workstation you must first:

1. Power down the workstation.

2. Disconnect power from the workstation.

3. Remove the workstation chassis access cover.

For detailed product-specific information, refer to the Service and Technical Reference Guide for your

HP workstation at http://www.hp.com/support/workstation_manuals.

Step 2–Configuring the SFF hard drive carrier for SFF hard

drives number 1, 2, and 3

Each SFF bay converter carrier consumes two 3.5-inch hard drive bays in the workstation. Before a bay

converter SFF hard drive carrier (provided in the SFF bay converter kit) can be installed in a workstation,

individual SFF hard drives (provided in SFF hard drive kits) must be loaded into the carrier. The following

figure shows a carrier configured with a single SFF hard drive and installed in an HP xw8600

Workstation. This figure also shows SFF hard drive numbers within this carrier.

4 Small form factor bay converter and hard drive installation ENWW

NOTE: To later install one or more additional SFF hard drives in the carrier (for example, hard drive

assignments number 2 and 3 as shown in the following figure), the carrier must be removed from the

workstation, the mounting rail and initially installed hard drive removed from the carrier, and all hard

drives then installed or reinstalled in the carrier in proper order by following these steps.

Figure 1 Carrier loaded with one SFF hard drive (drive number 1) and Installed in the HP xw8600

Workstation

To convert two workstation 3.5-inch hard drive bays to hold up to three 2.5-inch SFF hard drives,

complete the following steps:

1. Orient the empty SFF hard drive carrier as shown in the following figure and note the drive number

assignment of the hard drive loading slots within the carrier. When a fully configured carrier is

installed and with the workstation tower standing upright for typical operation, SFF hard drive

number 1 will be at the bottom of the workstation hard drive bays and hard drive number 3 at the

top (as shown in the preceding and the following figure).

Figure 2 SFF hard drive numbering order within the first carrier

ENWW Step 2–Configuring the SFF hard drive carrier for SFF hard drives number 1, 2, and 3 5

2. To load a hard drive into the SFF carrier, hold the hard drive body with the circuit board side facing

up. Ensure that the drive SAS connector is oriented to the carrier assembly as shown in the

following figure. Carefully spread the sides of the carrier (1) only enough to allow the hard drive to

fit into its desired mounting slot at an angle (2), as shown in the figure below.

NOTE: SFF hard drives must be loaded into the carrier in reverse order of their assigned drive

numbering, beginning with the highest number drive being loaded (as with hard drive number 3 in

the following figure example).

Figure 3 Loading hard drive number 3 in the carrier

3. Ensure that the two threaded holes in the edge of the hard drive body that was first lowered into

the carrier engage the two carrier locking pins for that drive mounting position. Continue to spread

the sides of the carrier (1 in the above figure) only enough to allow the opposite edge of the hard

drive to fit into the mounting slot and engage the two locking pins on that side of the carrier (as

shown in the following figure). The hard drive body should now be firmly mounted in the carrier.

Figure 4 Engaging the carrier locking pins when loading a hard drive

4. Repeat the above loading process for each desired SFF hard drive.

6 Small form factor bay converter and hard drive installation ENWW

NOTE: It may be necessary to engage the final two locking pins on drives number 2 and number

1 at the same time.

5. In the workstation chassis (see the following figure), remove the mounting rails from the two 3.5-

inch hard drive bays in which the SFF hard drive carrier will be installed (the bottom two bays in

the HP xw8600 Workstation). To unlock and remove a rail, simultaneously press the two locking/

release tabs at the upper end of the mounting rails inward (toward each other) while pulling upward.

Figure 5 Removing hard drive mounting rails from the HP xw8600 Workstation chassis

ENWW Step 2–Configuring the SFF hard drive carrier for SFF hard drives number 1, 2, and 3 7

6. On the SFF hard drive carrier, attach one of the removed hard drive mounting rails to the carrier,

oriented as shown in the following two figures. To affix the mounting rail, engage the four mounting

rail pins with the matching holes in the carrier.

Figure 6 Installing a mounting rail on the carrier (SFF hard drive number 1 shown loaded)

NOTE: When correctly installed, the mounting rail locking/release tabs are located adjacent to

the loaded SFF hard drive number 1 SAS connector (see the following figure).

Figure 7 Mounting rail and carrier orientation

8 Small form factor bay converter and hard drive installation ENWW

7. Insert the configured carrier assembly with mounting rail into the two workstation chassis 3.5-inch

hard drive bays, as shown in the following figure. Press down on the carrier assembly until the

mounting rail locks the assembly into the chassis.

Figure 8 Installing the configured SFF carrier assembly in the HP xw8600 Workstation

8. Attach a SAS-to-SATA connector adapter (provided in each SFF hard drive kit) to the SAS

connector of each installed SFF hard drive (see the following figure).

Figure 9 Attaching the SAS-to-SATA connector adapter to the hard drive SAS connector (HP

xw8600 Workstation)

9. On the adapter power cable provided in the bay converter kit (shown in the following figure):

a. Attach the white 4-pin straight connector (B) to an unused mating four-pin connector on the

power supply wiring harness at the rear of the optical drive bays in the workstation chassis.

ENWW Step 2–Configuring the SFF hard drive carrier for SFF hard drives number 1, 2, and 3 9

b. Attach the black right angle connector (A) to the SAS-to-SATA connector adapter on SFF hard

drive number 1 (see the following two figures).

Figure 10 Adapter power cable supplied with each carrier kit

NOTE: Connector C on the adapter power cable can be used to provide power to either an

optical drive bay or to a second adapter power cable and SFF hard drive carrier in the HP

xw8600 Workstation.

Figure 11 Attaching the adapter power cable to SFF hard drive number 1 (HP xw8600

Workstation chassis)

10 Small form factor bay converter and hard drive installation ENWW

Otros manuales para Xw6600 - Workstation - 2 GB RAM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de HP

HP StorageWorks DAT 40m Manual de usuario

HP StorageWorks 8B - FC Entry Switch Manual de instrucciones

HP LTO-2 HH Manual de usuario

HP StoreOnce B6000 Instrucciones de funcionamiento

HP StoreOnce 2700 Manual del operador

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP EY904AA - Personal Media Drive 160 GB External... Manual de usuario

HP StorageWorks X5000 Manual de instrucciones

HP StorageWorks P2000 Guía de referencia rápida

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Manual de usuario

HP 3PAR StoreServ 7200 2-node Manual de uso y cuidado

HP 330834-B21 - StorageWorks Ultrium 460 Tape Library Drive... Manual de usuario

HP StorageWorks 2300 - Disk System Guía rápida

HP StorageWorks 2000fc Manual de usuario

HP Surestore 6164 - Switch Manual de usuario

HP StorageWorks EML E Series Manual de usuario

HP StorageWorks XP1024 Manual de usuario

HP XP7 Manual de usuario

HP StorageWorks 300 - Virtual Library System EVA... Manual de usuario

HP XP20000/XP24000 Manual de usuario

HP 705 Guía de inicio rápido

HP StoreVirtual P4000 G2 Manual de servicio

HP XP7 Manual de usuario

HP OmniBook 2100 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario