HP StorageWorks EML E Series Manual de usuario

Removal

StorageWorks

EML E-Series

Drive Module

Installation

Caution: Parts can be damaged by

electrostatic discharge. Keep parts in their

containers until needed. Ensure that you

are properly grounded when touching

static sensitive components.

Note: This part is not hot-pluggable. It is

necessary to power down the library to

replace this part.

Note: An animation of the removal process

can be found on the documentation CD

shipped with the tape library.

Open the back

doors of the library.

Removal

StorageWorks

EML E-Series

Dre

Caution: Parts can bedamagedby

electrostatic discharge. Keep parts in their

containers until needed. Ensure that you

are properly grounded whentouching

static sensitive components.

Note: Thispart is hot-pluggable. It isnot

necessary to power downthelibrary to add

this part, however, the librarydoes have to be

power-cycled when adding or rep lacing a drive.

Note: Anew drive willnot be recognized

bythe library until aftera reboot.

Open theback door

of thelibrary.

StorageWorks

ESL

E-series

Interface

Manager

Caution:Partscanbedamagedby

electrostaticdischarge.Keeppartsintheir

containersuntilneeded.Ensureyouare

properlygroundedwhentouchingstatic-

sensitivecomponents.

Note:Thispartisnothot-pluggable.

Itisnecessarytopowerdownthelibrary

toreplacethispart.

10026

Openthebackdoorofthelibrary.

Inspectthecontentsofthekit.

Powerdownthelibrary.

a.Placethelibraryoff-linebypressingthe

Standbybuttononthelibrary'sfrontpanel.

Thelibraryroboticscompletesanycurrent

commandsandthenstops.

b.Verifythatthefrontpaneldisplayindicates

“SystemOff-line”.

c.Verifythatthepickerisempty.Ifthereisa

tapecartridgeinthepicker,performaMove

commandtoplacethecartridgeinan

availableslot.[Contentneeded.]

d.Pressandholdthepowerbuttonlocatedon

thefrontofthelibrarybehindthelaptoptray

untilthefrontpanelgoesblank.

Flipthetwobreakerswitchesoffatthepower

distributionunit.

Inspect the contents of the kit. You may need a

flat-blade screwdriver to remove and replace this

tape drive.

If you are removing anexisting tape drive,

make sure tounloadanytape cartridges in

thedrive to beremoved using your application

software or thelibrary GUI touch screen. Use

your backup software to cease library activity.

Identifythe tape drive to bereplaced. The Fault

LED light may be lit, signifying a hot swap can

occur.

Inspect the contents of the kit. You may need a

flat-blade screwdriver to remove and replace this

tape drive.

If you are removing an existing tape drive,

make sure to unload any tape cartridges in

the drive to be removed using your application

software or the library GUI touch screen. Use

your backup software to cease library activity.

Identify the tape drive to be replaced. The Fault

LED light may be lit, signifying a hot swap can

occur.

Installation

Disconnect the FC cable from the drive to

be replaced by pressing down on the cable

connector tab and pulling the connector away

from the drive.

Caution: To avoid damaging FC cables,

do not pinch or sharply bend the cables

tighter than a 5 centimeter (2-inch) diameter.

Connect an FC cable to the FC connector on the

new drive. The FC cable should click into place.

Caution: To avoid damaging FC cables,

do not pinch or sharply bend the cables

tighter than a 5 centimeter (2-inch) diameter.

Connect the other end of the FC cable to its

corresponding port on the interface controller

card. Attach a label to each end of the cable to

mark the port designations. Complete this cabling

process for all drives.

If necessary, use a flat-blade screwdriver to loosen

the captive screw at the right side of the drive

module. Grasp the drive and pull the drive from

the drive bay.

To install a new drive, locate a vacant drive bay.

Remove the face plate covering the drive bay by

removing the screw holding it in place.

Remove the end cap from the FC connector on

each new tape drive to be installed. Insert the new

drive module into the vacant drive bay and tighten

the captive screw to secure the drive to the chassis.

Note: Replacing an existing tape drive

does not require power-cycling the library,

however, adding a new tape drive does

require power-cycling the library.

Verify that the FC port LED on the interface

controller card is solid green.

If necessary, upgrade the drive firmware using

the Interface Manager's Command Line Interface.

See the HP StorageWorks Interface Manager

and Command View TL User's Guide for detailed

procedures on upgrading drive firmware.

Note: A new drive will not be

recognized by the library until after a

reboot.

Getting help

• HP product information:

http://www.hp.com/products/tapestorage

• HP technical support and phone numbers:

http://www.hp.com/support

• HP StorageWorks Library and Tape Tools

(L&TT) diagnostic software:

http://www.hp.com/support/tapetools

• Interface Manager and HP StorageWorks

Command View TL:

http://www.hp.com/support/cvtl

Close the back

doors of the library.

First Edition (April 2005)

Part Number: AD560-96013

*AD560-96013*

AD560-96013

Otros manuales de Almacenamiento de HP

HP DW017B - StorageWorks Ultrium 448 Tape Drive Manual de instrucciones

HP StorageWorks EVA4000 Guía

HP C2233 Manual de usuario

HP D2D100 Manual de usuario

HP P2000 G3 Guía de referencia rápida

HP StorageWorks Disk System 2405 Manual de uso y cuidado

HP 1040 Manual de programación

HP StorageWorks XP48 - Disk Array Manual de usuario

HP EVA P6000 Manual de usuario

HP BL536A Manual de usuario

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Guía

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Instrucciones de instalación y funcionamiento

HP StorageWorks 8B - FC Entry Switch Manual de usuario

HP P9000 Manual de usuario

HP 9840 Manual de usuario

HP Storevirtual 4000 Manual de usuario

HP 5243 Manual de usuario

HP LTO Ultrium Manual del producto

HP Surestore FC10 - Disk Array Manual de usuario

HP Storevirtual 4000 Manual de usuario

HP P2000 G3 Manual de usuario

HP IBRIX 9300 Manual de servicio

HP HP 7936 Instrucciones de instalación

HP 12Gb SAS SSDs Instrucciones de uso

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario