HP StorageWorks DAT 40m Manual de usuario

getting started guide

hp StorageWorks

DAT tape drive

removable model

DAT 40m, DAT 72m

hp tape array 5300

Removable drives - contents

Pre-Installation

Before you start page 3

Backup software and drivers page 5

Using the CD-ROM page 7

Checking the SCSI connection page 9

Checking the configuration switches (UNIX systems) page 11

Installing the tape drive

Step 1: Install the drive page 13

Step 2: Set the drive’s SCSI ID page 15

Step 3: Verify installation page 17

Using the tape drive

Your HP StorageWorks DAT tape drive page 19

Use the correct media page 21

Replacing the drive page 25

Using HP OBDR page 27

Diagnostic tools page 29

Optimizing performance page 30

Troubleshooting page 31

Problems with cartridges page 36

Other sources of information page 38

dds-removable-frame6.fm Page 1 Monday, January 5, 2004 5:04 PM

November 2003

Part Number: C7497-90905

Hewlett-Packard Company makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and fitness for a

particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use

of this material.

This document contains proprietary information, which is protected by copyright. No part of

this document may be photocopied, reproduced, or translated to another language without

the prior written consent of Hewlett-Packard. The information contained in this document is

subject to change without notice.

Microsoft®, MS-DOS®, MS Windows®, Windows®and Windows NT®are U.S.

registered trademarks of Microsoft Corporation.

UNIX®is a registered trademark of The Open Group.

Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions

contained herein. The information is provided ”as is” without warranty of any kind and is

subject to change without notice. The warranties for Hewlett-Packard Company products are

set forth in the express limited warranty statements for such products. Nothing herein should

be construed as constituting an additional warranty.

Printed in the U.K.

Product Details

Write your tape drive details here so you can find them easily if you need them. The model name is on the

front of the drive and the product and serial numbers are on a label on the bottom of the drive.

Model (type of drive):

Model (number):

Serial (number):

Warranty Serial (number):

Date purchased/installed:

SCSI ID:

dds-removable-frame6.fm Page 2 Monday, January 5, 2004 5:04 PM

Before you start

HP StorageWorks DAT models

This guide describes how to install and operate the following HP StorageWorks DAT rack-

mount tape drive models:

•HPStorageWorksDAT72

•HPStorageWorksDAT40

Which operating systems are supported?

HP StorageWorks DAT drives can be connected to servers running under Windows®,

NetWare, UNIX, Tru64 and Linux. Refer to the “HP StorageWorks Tape Software

Compatibility” topic on our World Wide Web site (www.hp.com/go/connect) for more

information about the operating system versions that are supported.

Which rackmount systems can I use?

HP StorageWorks DAT removable tape drives are used in conjunction with the

HP Tape Array 5300 system, which can be used with both full-height and half-height tape

drives. It will hold up to four HP StorageWorks DAT tape drives. The tape array is designed to

be installed into HP, IBM and other compatible 19” rackmount systems. It must be properly

installed and configured. Refer to your tape array documentation for further details.

Airflow requirements

The HP Tape Array 5300 is designed to provide adequate airflow for up to four half-height or

up to two full-height tape drives. As long as the tape array is fully populated, it will provide

adequate airflow for your HP StorageWorks DAT tape drives. If you have unused bays in the

tape array, you must install the blanking plates provided with the tape array. This ensures that

there is adequate airflow to the drives. See the documentation with the tape array for details

on installing blanking plates.

You should ensure that ventilation is adequate at the front and rear of the tape array.

How do I connect the drive to my server?

The individual tape drives are connected to their host server via the high density LVD/SE SCSI

connectors on the back of the tape array. They do not require any SCSI cables to plug into the

tape array. However, suitably-rated cabling and terminators are required to connect the tape

array with the SCSI host. You will need a properly installed and configured SCSI host bus

The following guidelines apply:

• For optimum performance the drive should be the only device on the SCSI bus.

• If you daisy-chain devices, make sure that devices are of the same SCSI type and that

each device on the same SCSI bus has a unique SCSI ID and is terminated appropriately.

Do not daisy-chain more than two devices on the same SCSI bus (for example, two LVD

Wide Ultra drives).

• Always terminate the SCSI bus.

• Do not attach the drive to the same SCSI bus as a your disk drive or to a RAID controller.

dds-removable-frame6.fm Page 3 Monday, January 5, 2004 5:04 PM

adapter (HBA) or a built-in SCSI controller on your SCSI host with a spare low voltage

differential (LVD) SCSI port and LVDS-compatible cables and terminators. See “Checking the

SCSI connection” on page 9.

Why is the SCSI bus type important?

The SCSI bus type determines the speed at which data can be transferred between devices on

the bus and the maximum length of cable that can be used. The drives support a burst transfer

rate of 40 MB/sec. To benefit from this level of performance, it is important to ensure that the

drives are connected to a SCSI bus of a similar or higher specification. This means that you

need:

•An Ultra Wide, Ultra2 Wide, Ultra3 (160) or Ultra4 (320) SCSI bus. Ultra Wide SCSI

supports the maximum bus speed of 40 MB per second, Ultra2, Ultra3 and Ultra4 SCSI

exceeds this.

•LVD-rated SCSI cabling and terminators. The LVD interface enables the data to be

transferred at the drive's maximum rate and provides a maximum cable length of 12 meters.

If you attach the drive to a lower specification SCSI bus, it may still work but data will not be

transferred as quickly and you will need to use shorter cable lengths.

Note The drives are not compatible with high voltage differential (HVD) SCSI devices.

How can I check the SCSI bus type and SCSI ID?

For many operating systems, you can install HP Library & Tape Tools from www.hp.com/

support/tapetools and run the “Install Check” to check your server’s current SCSI

configuration (see page 29). This will provide information about the SCSI bus and the SCSI

IDs in use. See also the SCSI topic in the electronic User’s Guide on the

HP StorageWorks Tape CD-ROM for other ways of checking the SCSI bus type.

Do I need additional items for installation?

• You will need to order the correct size SCSI cables and terminators to suit the particular

configuration of your tape array. Cable and terminator options are listed at the HP tape

array support web site:www.hp.com/go/tapearray, and can be ordered from your

local HP sales office. Refer to your tape array’s Getting Started Guide for details of how to

install SCSI cables and terminators on the rear panel of the tape array. The latest version of

this document can also be downloaded from www.hp.com/go/tapearray.

• If you do not have a spare, suitably rated SCSI connector on your server, you must install a

new HBA (also known as a SCSI card). This should be of an Ultra Wide or higher SCSI

specification. We recommend that a 64-bit Ultra 3 (160) HBA is used. You will need to

purchase and install the new HBA into an unused, 64-bit PCI expansion slot within your

server before installing your tape drive. (The kit can also be installed in a 32-bit PCI

expansion slot, but performance may be degraded.)

Refer to our World Wide Web site for recommended products, configurations and ordering

information: www.hp.com/go/connect or www.hp.com/support.

dds-removable-frame6.fm Page 4 Monday, January 5, 2004 5:04 PM

Backup software and drivers

Backup software

For optimum performance it is important to use a backup application that is appropriate for

your system’s configuration. In a direct attach configuration, where the tape drive is attached

to a standalone server, you can use backup software that is designed for a single server

environment. In network configurations you will need backup software that supports enterprise

environments. HP, Veritas, Legato, Yosemite and Computer Associates all provide suitable

products. Further details about these and other products that may be appropriate can be

found on our connectivity web site.

1Go to our connectivity web site: www.hp.com/go/connect and select tape backup.

2Select software compatibility.

3Select your combination of operating system and tape drive model in the table. A list of

supported backup applications is displayed. This will also tell you whether your configuration

is compatible with HP One-Button Disaster Recovery, HP OBDR. (All HP StorageWorks DAT

tape drives support HP OBDR. However, you can only use this feature if your system

configuration and backup application also support it. See “Using HP OBDR” on page 27.)

4Make sure you have a backup application that supports HP StorageWorks DAT tape drives and

download any upgrades or patches, if required.

Drivers

Windows users

Before you install the tape drive, download the HP driver from our web site: www.hp.com/

support. Refer to the accompanying README file for specific installation instructions for

Windows NT, Windows 2000, Windows XP and Windows Server 2003 drivers. This will tell

you whether you need to install the driver before or after installing the tape drive.

If you do not have internet access, you can also download drivers from the

HP StorageWorks Tape CD-ROM, but these may not be the latest versions available.

UNIX users

The recommended backup applications use the operating system’s standard, built-in device

drivers. To upgrade drivers we recommend that you patch to the latest version of the operating

system or configure device files, as described in the UNIX Configuration Guide on the CD-

ROM.

IA64 users

If you are installing on an IA64 system, such as an HP Integrity server, check www.hp.com/

go/connect for the latest information on the availability of backup application upgrades

and drivers.

dds-removable-frame6.fm Page 5 Monday, January 5, 2004 5:04 PM

HP Product

Registration

User

Documentation

CD-ROM Guide

Drivers

HP Library &

Tape Tools

Figure 1: the HP StorageWorks Tape CD-ROM

dds-removable-frame6.fm Page 6 Monday, January 5, 2004 5:04 PM

Using the CD-ROM

HP product registration

To register your new tape drive electronically via the web, use the “Product Registration” link

on the HP StorageWorks Tape CD-ROM.

Drivers

For detailed information about drivers, refer to the appropriate README file in the DRIVERS

directories on the HP StorageWorks Tape CD-ROM. There is a separate sub-directory for each

operating system.

User documentation

Refer to the “User Documentation” topic on the HP StorageWorks Tape CD-ROM for a UNIX

Configuration guide and an online User’s Guide that provides more detailed information

about using your HP StorageWorks DAT tape drive.

Refer to your backup application’s documentation for instructions on how to back up and

restore data.

HP Library & Tape Tools

HP Library & Tape Tools software provides diagnostic and troubleshooting utilities. It allows

you to identify your product correctly, check SCSI ID information on the SCSI bus, run tests,

carry out firmware upgrades and, if necessary, generate comprehensive troubleshooting

information for support calls. Use the link on the HP StorageWorks Tape CD-ROM to access

our Support web site, www.hp.com/support/tapetools, and download the latest

version of this software. For further details see page 29.

CD-ROM guide

The CD-ROM guide provides an overview of the CD directory structure and information about

the languages in which the contents of the CD-ROM are available. It also contains a set of

URLs and links for further information.

The HP StorageWorks Tape CD-ROM contains drivers, useful utilities and information to help

you install and use your tape drive. For most operating systems, HP Library & Tape Tools will

help you check SCSI ID information on the SCSI bus before installation. The UNIX

Configuration guide on the CD-ROM also contains information about checking SCSI IDs on

UNIX systems.

dds-removable-frame6.fm Page 7 Monday, January 5, 2004 5:04 PM

Figure 2: checking the SCSI connection

dds-removable-frame6.fm Page 8 Monday, January 5, 2004 5:04 PM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de HP

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Manual de instrucciones

HP StorageWorks P2000 Manual de usuario

HP StorageWorks EVA4000 Guía

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de usuario

HP StorageWorks X5000 Manual de instrucciones

HP 9840 Manual de usuario

HP 705 Guía de inicio rápido

HP Surestore Disk Array 12h - And FC60 Manual de usuario

HP 157770-001 - DAT Drive 20/40 Tape Manual de usuario

HP StorageWorks vs80 Manual de usuario

HP ProLiant SB460c - SAN Gateway Storage Server Manual de usuario

HP 3000 - 37XE System Manual de instrucciones

HP Ultrium 230e Manual de usuario

HP StoreEasy 3000 Manual de servicio

HP Surestore 160ex - Optical Jukebox Manual de usuario

HP StoreOnce B6000 Manual de usuario

HP EX950 M.2 Manual de usuario

HP Converged Architecture 700 Guía de referencia rápida

HP Surestore Tape Library Model 2/15 Manual de usuario

HP StorageWorks 600 - Modular Disk System Manual

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Guía

HP P10000 Manual de usuario

HP Surestore Disk Array 12h - And FC60 Instrucciones de montaje

HP StorageWorks XP48 - Disk Array Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario