HP StorageWorks P2000 Manual de usuario

HP P2000 G3 MSA System

Event Descriptions Reference Guide

Part number: 591224-004

First edition: May 2011

Legal and notice information

Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial

Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under

vendor’s standard commercial license.

The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Acknowledgements

Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.

UNIX is a registered trademark of The Open Group.

HP P2000 G3 MSA System Event Descriptions Reference Guide 3

Introduction

This guide is for reference by storage administrators to help troubleshoot storage-system issues. It describes

event messages that may be reported during system operation and specifies any actions recommended in

response to an event.

Events and event messages

When an event occurs in a storage system, an event message is recorded in the system’s event log

and—depending on the system’s event notification settings—may also be sent to users (via email) and

host-based applications (via SNMP or SMI-S).

Each event has a numeric code that identifies the type of event that occurred, and has one of the following

severities:

•Critical. A failure occurred that may cause a controller to shut down. Correct the problem immediately.

•Error. A failure occurred that may affect data integrity or system stability. Correct the problem as soon

as possible.

•Warning. A problem occurred that may affect system stability but not data integrity. Evaluate the

problem and correct it if necessary.

•Informational. A configuration or state change occurred, or a problem occurred that the system

corrected. No immediate action is required. In this guide, this severity is abbreviated as “Info.”

An event message may specify an associated error code or reason code. Error codes and reason codes

are outside the scope of this guide.

Event format in this guide

This guide lists events by event code and severity, where the most severe form of an event is described first.

Events are listed in the following format. Events that do not apply to P2000 G3 MSA System products are

not listed.

Resources for diagnosing and resolving problems

For further information about diagnosing and resolving problems, see:

•The troubleshooting chapter and the LED descriptions appendix in your product’s user guide

•The topic about verifying component failure in the component’s replacement instructions document

These and other HP documents can be found

on the

Software Support/Documentation CD

shipped with your

product or at http://www.hp.com/support/manuals.

For links to additional information about your product, see

http://www.hp.com/go/p2000

http://www.hp.com/go/msa.

For product support and to download drivers

and software, see

http://www.hp.com/support.

For a summary of storage events and corresponding SMI-S indications, see Events sent as indications to

SMI-S clients on page 45.

Event code

Severity Event description.

Recommended actions

•If the event indicates a problem, actions to take to resolve the problem.

Event descriptions

Warning Either:

•The indicated non-RAID-6 vdisk is operating with degraded health due to the failure of one disk.

•The indicated RAID-6 vdisk is operating with degraded health due to the failure of two disks.

The vdisk is online but cannot tolerate another disk failure.

If a dedicated spare or global spare of the proper size and type is present, that spare is used to

automatically reconstruct the vdisk. If an assigned spare is not present, but an available disk of the proper

type and size is present and the dynamic spares feature is enabled, that disk is used to automatically

reconstruct the vdisk.

Recommended actions

•If no spare is present and the dynamic spares feature is disabled, replace the failed disk and use SMU

to add the new disk as a dedicated spare for the vdisk. That spare is used to automatically reconstruct

the critical vdisk.

•Replace the failed disk for future use.

•If the replacement disk was previously used in another vdisk and has status LEFTOVR, use SMU to

clear the disk’s metadata so you can assign the disk as a spare for the critical vdisk or for future use.

•See also Table 1 on page 42.

Error The indicated vdisk went offline. Either one disk failed for RAID 0 or NRAID; three disks failed for RAID 6;

or two disks failed for other levels. The vdisk cannot be reconstructed.

Recommended actions

•Use the trust command as described in the CLI reference guide.

Info. The indicated disk had an uncorrectable error and the controller reassigned the indicated block.

Recommended actions

•Monitor the error trend and whether the number of errors approaches the total number of bad-block

replacements available.

Warning Vdisk creation failed during initialization.

Recommended actions

•In SMU’s System Overview panel, compare the vdisk count with the configuration limit for the maximum

number of vdisks.

• If you reached this limit, either purchase additional storage or removed unneeded vdisks.

• If you have not reached the limit, see Resources for diagnosing and resolving problems on page 3.

Info. Vdisk creation either immediately failed, was canceled by the user, or succeeded.

Recommended actions

•No action required.

Error In a testing environment, a controller diagnostic failed and reports a product-specific diagnostic code.

Recommended actions

•Perform failure analysis.

HP P2000 G3 MSA System Event Descriptions Reference Guide 5

Warning The indicated disk in the indicated vdisk failed and the vdisk changed to a critical or offline state. If a

spare is present the controller automatically uses the spare to reconstruct the vdisk. Subsequent events

indicate the changes which happen to the vdisk.

Recommended actions

•See Table 1 on page 42.

When the problem is resolved, event 9 is logged.

Info. The indicated spare disk has been used in the indicated critical vdisk to bring it back to a fault-tolerant

state. Vdisk reconstruction starts automatically.

This event indicates that a problem reported by event 8 is resolved.

Recommended actions

•No action required.

Info. The indicated disk has been designated a global spare.

Recommended actions

•No action required.

Warning Vdisk reconstruction failed.

Recommended actions

•Determine whether the reconstruction failed due to a disk problem and whether replacing that disk will

enable reconstruction to start and complete without further errors.

Info. Vdisk reconstruction succeeded.

Recommended actions

•No action required.

Info. A rescan has completed.

Recommended actions

•No action required.

Info. Storage Controller firmware update has completed.

Recommended actions

•No action required.

Warning Vdisk verification failed during the verification process.

Recommended actions

•See Resources for diagnosing and resolving problems on page 3.

Info. Vdisk verification failed immediately, was aborted by a user, or succeeded.

Recommended actions

•No action required.

Info. Vdisk creation has started.

Recommended actions

•No action required.

Info. The statistics for the indicated vdisk have been reset.

Recommended actions

•No action required.

Info. Cache parameters have been changed for the indicated vdisk.

Recommended actions

•No action required.

Info. Controller parameters have been changed. This event is logged when general configuration changes are

made; for example, utility priority, remote notification settings, user interface passwords, and management

port IP values. This event is not logged when changes are made to vdisk or volume configuration.

Recommended actions

•No action required.

Info. The indicated disk is no longer a global or dedicated spare.

Recommended actions

•No action required.

Info. Vdisk verification has started.

Recommended actions

•No action required.

Info. Controller time/date has been changed. This event is logged before the change happens so the event

timestamp shows the “old” time. (May appear often if NTP is enabled.)

Recommended actions

•No action required.

Info. Controller has been restored to factory defaults.

Recommended actions

•For an FC controller, restart it to make the default loop ID take effect.

Info. Vdisk reconstruction has started.

Recommended actions

•No action required. When complete, event 18 is logged.

HP P2000 G3 MSA System Event Descriptions Reference Guide 7

Warning The sensors monitored a temperature or voltage in the warning range.

Recommended actions

•Check that the storage system’s fans are running.

•Check that the ambient temperature is not too warm. The enclosure operating range is 41–104°F

(5–40°C).

•Check for any obstructions to the airflow.

•If none of the above explanations apply, replace the controller FRU that reported the error.

When the problem is fixed, event 47 is logged.

Error The sensors monitored a temperature or voltage in the failure range.

Recommended actions

•Check that the storage system’s fans are running.

•Check that the ambient temperature is not too warm. The enclosure operating range is 41–104°F

(5–40°C).

•Check for any obstructions to the airflow.

•If none of the above explanations apply, replace the controller FRU that reported the error.

When the problem is fixed, event 47 is logged.

Info. The indicated disk has been designated a spare for the indicated vdisk.

Recommended actions

•No action required.

Info. The indicated vdisk has been deleted.

Recommended actions

•No action required.

Warning The controller contains cache data for the indicated volume but the corresponding vdisk is not online.

Recommended actions

•Determine the reason that the disks are not online.

•If an enclosure is down, determine corrective action.

•If the vdisk is no longer needed, you can clear the orphan data; this will result in lost data.

•If the volume is missing and was not intentionally removed, see Resources for diagnosing and resolving

problems on page 3.

Info. A communication failure has occurred between the controller and an enclosure management processor

(EMP).

Recommended actions

•No action required.

Info. An error detected by the sensors has been cleared. This event indicates that a problem reported by event

39 or 40 is resolved.

Recommended actions

•No action required.

Info. The indicated vdisk has been renamed.

Recommended actions

•No action required.

Info. A lengthy SCSI maintenance command has completed. Output indicates whether it completed successfully

or a failure occurred. (Typically appears after disk firmware update.)

Recommended actions

•No action required.

Info. A correctable ECC error occurred in buffer memory.

Recommended actions

•No action required.

Error An uncorrectable ECC error occurred in buffer memory.

Recommended actions

•If this event occurs only once, no action is required.

•If the event occurs more than once, replace the controller reporting the event.

Info. Vdisk expansion has started.

Recommended actions

•This operation can take days to complete. When complete, event 53 is logged.

Info. Vdisk expansion either completed, failed, or was aborted by a user.

Recommended actions

•If the expansion failed because of a disk problem: replace the disk; if vdisk reconstruction starts, wait

for it to complete; and then retry the expansion.

Warning A SMART event occurred on the indicated disk, indicating impending disk failure.

Recommended actions

•See Table 1 on page 42.

Info. A controller has powered up or restarted.

Recommended actions

•No action required.

HP P2000 G3 MSA System Event Descriptions Reference Guide 9

Warning A disk drive or enclosure management processor (EMP) detected a serious error, such as a parity error or

disk hardware failure.

Recommended actions

•If the event indicates that a disk or an expansion module is bad, replace the indicated device.

Info. A disk drive or enclosure management processor (EMP) detected a non-serious error.

Recommended actions

•No action required.

Warning The controller detected a parity error while communicating with the indicated SCSI device. The error was

detected by the controller, not the disk.

Recommended actions

•If the event indicates that a disk or an expansion module is bad, replace the indicated device.

Info. The controller detected a non-parity error while communicating with the indicated SCSI device. The error

was detected by the controller, not the disk.

Recommended actions

•No action required.

Info. A disk channel was reset from another initiator or target.

Recommended actions

•No action required.

Error The controller reset the indicated disk channel to recover from a communication error. This event is logged

to identify an error trend over time.

Recommended actions

•If the controller recovers, no action is required.

•View other logged events to determine other action to take.

Warning The indicated global or dedicated spare disk has failed.

Recommended actions

•Replace the failed disk.

Error An uncorrectable ECC error occurred on the buffer memory on startup. The controller is automatically

restarted and its cache data is restored from the partner controller’s cache.

Recommended actions

•Replace the controller module.

Info. The controller has identified a new disk or group of disks that constitute a vdisk and has taken ownership

of the vdisk. This can happen when disks containing data have been inserted from another enclosure. This

event only applies to non-Active-Active controllers.

Recommended actions

•You may need to clear the disks’ metadata if you want to reuse them in one or more new vdisks.

Info. The controller that logged this event is shut down, or both controllers are shut down.

Recommended actions

•No action required.

Info. The controller has started or completed failing over.

Recommended actions

•No action required.

Info. After failover, recovery has either started or completed.

Recommended actions

•No action required.

Info. The two controllers are communicating with each other and cache redundancy is enabled.

Recommended actions

•No action required.

Info. The FC loop ID for the indicated vdisk was changed to be consistent with the IDs of other vdisks. This can

occur when disks containing a vdisk are inserted from an enclosure having a different FC loop ID.

This event is also logged by the new owning controller after vdisk ownership is changed.

Recommended actions

•No action required.

Info. The indicated volume’s LUN has been unassigned because it conflicts with LUNs assigned to other

volumes. This can happen when disks containing data for a mapped volume have been inserted from

another enclosure.

Recommended actions

•If you want hosts to access the volume data on the inserted disks, map the volume with a different LUN.

Info. The controller is using default configuration settings. This event occurs on the first power up, and might

occur after a firmware update.

Recommended actions

•If you have just performed a firmware update and your system requires special configuration settings,

you must make those configuration changes before your system will operate as before.

Info. The cache was initialized as a result of power up or failover.

Recommended actions

•No action required.

Otros manuales para StorageWorks P2000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de HP

HP P9000 Manual de usuario

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Manual de usuario

HP PD5000Z Manual de usuario

HP StorageWorks TL895 Manual de usuario

HP StorageWorks P4000 Series Manual de usuario

HP StoreOnce B6000 Manual de funcionamiento

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Manual de usuario

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP 418371-B21 - Dual Port 72 GB Hard Drive Manual de usuario

HP Invent Q1573 Series Instrucciones de montaje

HP Pavilion p6000 - Desktop PC Guía

HP P9000 Manual de usuario

HP StorageWorks 8000 - NAS Manual de instrucciones

HP Surestore Disk Array 12h - And FC60 Manual de usuario

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP D2D Guía de instalación y uso

HP EX920 M.2 Manual de usuario

HP LTO-4 HH Manual de usuario

HP StorageWorks P4000 Series Manual de usuario

HP StorageWorks 7110 - Virtual Array Guía de inicio rápido

HP XP7 Manual de usuario

HP D2D Manual de usuario

HP AU183AA - 2TB Personal Media Drive Manual de uso y mantenimiento

HP StorageWorks TL895 Guía rápida

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario