HP StorageWorks 7110 - Virtual Array Manual de usuario

VA Virtual Front Panel Commands

HP15 Firmware Release

April, 2002

Command Function

help Displays a description of each command.

setup Performs Virtual Front Panel configuration.

dsp Displays subsystem status.

cfg Performs subsystem configuration (LUN creation).

mgr Performs subsystem management operations.

fmt Performs an subsystem format.

rbld Performs rebuild operations.

recover Performs NVRAM recovery operations.

secure Performs security operations.

log Displays Logs

scsi Performs scsi command for provided cdb.

Usage Notes

To maintain consistency with earlier versions of the VFP, all commands can be prefaced with "vfp".

For help with a specific command, use the -? Option. For example, setup -?

For command recall, type “<” or “>”.

Command Options and Arguments Description

setup -e {on | off}

-r <value>

-c <value>

-b <int>

-e: Sets character echo

-r: Sets the number of rows:

<value>: range 5 – 1000

-c: Sets the number of columns:

<value>: ranger 40 - 8000

-b: Sets baud rate

<int> : 0, 1, 2, or 3

for 9600, 19200, 38400, 57600

Note: A firmware reset will restore the

default value of 9600.

dsp dsp (no argument follows)

-c [m/c1 | m/c2]

-d [fruLocation]

-L [LUN ID]

-s

-e

-f

Displays general information about the

subsystem.

-c: display controller information:

m/c1: controller 1, m/c2 controller 2

-d: display drive information:

[fruLocation] m/d#

-L: display LUN information (default for

all existing luns).

[LUN ID]: specify a requested LunID

-s: display subsystem settings

-e: enclosure information

-f: list of discovered FRUs

cfg cfg -L <LUN ID> -a <capacity> [{G|g}|{K|k}] –g <RG Id>

To Create a LUN requires three

parameters, LUN ID, capacity and RD

Id.

-L <LUN ID>: specify LUN ID to be

created.

-a <capacity>: specify LUN capacity.

Capacity is default to MB.

If followed by ‘K’ or ‘k’, the capacity is in

kilobytes and must be a multiple of

512.

If followed by ‘G’ or ‘g’, the capacity is in

gigabytes.

-g <RG ID>: redundancy group id. For

VA 7100 set to 1, for VA 7400 set to 1

or 2.

For valid number of LUNs to create,

check dsp –s for CREATE LUN LIMIT.

cfg -L <LUN ID> -d -L followed by –d: deletes LUN, no

need to specify capacity, just LUN ID.

mgr -s {shut | start}

-R {full | partial}

-L <loop id> -c {1|2}

-t {1 | 2 | 4} –c {1|2}

-S {1 | 2} –c {1 | 2}

-os {hpux | nt | win2k | linux | solaris | aix | netware |

generic | tru64 | openVMS | mpe | solarisCluster} –c {1 | 2}

-B {autoraid | raid1}

-O { on | off }

-q <queue full threshold>

-ds { on | off }

-p {on | off }

-V <Revision>

-s: Shutdown or restart the disk array

-R: Reset the disk array

-L: Set the FC Port Loop ID for the

Controller Port.

-t: Set the topology for the Controller

Port. Valid Arguments:

1- Private Topology

2 - Public Topology

4- Direct Fabric Attached Topology.

-S: Set the FC Port Speed for the

Controller Port.

Valid Arguments:

1- 1 GBit/sec Data Rate

2- 2 GBit/sec Data Rate

-c: Controller for which the port speed

will be set.

-os: Set Host behavior for controller

specified.

-c: Controller for which the host

behavior will be set.

-B: sets array RAID level (AutoRaid |

RAID 1).

-O: set enable optimize policy on/off.

-q: set queue full threshold ( 0 to 4096)

-ds: set disable secondary path

presentation

The -ds option determines whether the

array makes the non-optimal path to

LUNs visible to hosts. When set to ON,

secondary path presentation is enabled

and all LUNs are “visible” through all

ports on all controllers. When set to

OFF, each LUN will be “visible” only on

the controller that is the optimal

controller for that LUN. The optimal

controller is the one associated with the

redundancy group of which the LUN is a

part.

-p: Enable/disable prefetch.

-V: Set volume set revision. Valid

arguments:

1 – For HP01, HP02, HP11, HP13

2 – For HP14, HP15 and greater

fmt No options Perform array format (will destroy all

user data). User will be prompted with a

yes/no. The word ‘yes’ must be

entered completely. Otherwise the

format command will be canceled.

rbld -p

-a {on | off}

-p: Displays status/progress of a

subsystem rebuild.

-a: enables or disables autorebuild

recover No options

-s

Perform a recover process. Will ask for

user’s verification to proceed.

-s: returns the recoverability status or

the disk array, as well as the status of

the recovery progress.

secure -R

-e

-d

-R: Resets the password to AUTORAID.

-e: enables security.

-d: disables security.

log No options

-p <number of most recent events to display>

The log command ignores the row settings. If row setting

is less than 25, log command will set it to 25. In any case,

the row setting will be ignored when dispalying logs.

No options displays all events in buffer.

-p: display a given number of most

recent events.

scsi -cdb <cdblen> <cdb bytes…> <direction> [ -cdbcrc <cdb

crc>]

[ -lun <lunId> ]

[ -data <data len> <data bytes…> [ -datacrc <data crc> ] ]

direction can be: nodata | datain |

dataout

Documentation about this interface is

available upon request.

Otros manuales para StorageWorks 7110 - Virtual Array

Otros manuales de Almacenamiento de HP

HP LTO-3 960 Instrucciones de uso

HP LTO Ultrium Manual del producto

HP X510 Instrucciones de uso

HP StorageWorks MSL2024 Guía de referencia

HP P9000 Manual de usuario

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Manual de usuario

HP D2D Manual de usuario

HP MSA 30 Manual de usuario

HP StorageWorks 1000 - Modular Smart Array Manual de servicio

HP C7401A - SureStore Ultrium 230 Tape Drive Manual de usuario

HP StorageWorks P2000 Manual de usuario

HP P9000 Manual de usuario

HP AU183AA Manual de usuario

HP StorageWorks DLT 80 Instrucciones de uso

HP Colorado Trakker 250 Manual de instrucciones

HP StorageWorks DAT 72 Manual de usuario

HP P9000 Manual de usuario

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Manual

HP 5243-2SE Manual de usuario

HP StorageWorks 8B - FC Entry Switch Manual de usuario

HP POD 20c Manual

HP StorageWorks MSL6000 series Manual de usuario

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario