HP Xw4550 - Workstation - 2 GB RAM Manual de usuario

SATA optical drive installation

This document describes how to install a Serial ATA (SATA) optical disk drive (ODD) on your

workstation.

Kit contents

Ensure that the following components are included in your optical drive kit:

●5.25-inch, half-height SATA ODD

●SATA interface cables

●Four M3 guide screws

●Warranty

trademark of Hewlett-Packard Development Company, L.P. Microsoft and Windows are

U.S. registered trademarks of Microsoft Corporation. Printed in the U.S.

ENWW Kit contents 1

HP xw Workstation series

Warnings and cautions

WARNING! Any surface or area of the equipment marked with these symbols indicates the

presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists.

To reduce the risk of injury from a hot component, allow the surface to cool before touching.

WARNING! Any surface or area of the equipment marked with these symbols indicates the

presence of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open

any enclosed area.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper

workstation, setup, posture, and health and work habits for computer users, and provides important

electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/

ergo and/or on the documentation CD if one is included with the product.

WARNING! If a product is shipped in packaging marked with this symbol, , the product must always

be lifted by two persons to avoid personal injury due to product weight.

CAUTION: Static electricity can damage the electronic components of the workstation. Before

beginning these procedures, be sure you are discharged of static electricity by briefly touching a

grounded metal object.

CAUTION: Observe the following cautions when removing or replacing a processor:

— Installing a processor incorrectly can damage the system board. Have an HP authorized reseller or

service provider install the processor. If you plan to install it yourself, read all of the instructions carefully

before you begin.

— Failure to follow the workstation preparation instructions and these result in an improperly installed

processor, causing extensive system damage.

— Processor socket pins are delicate and bend easily. Use extreme care when placing the processor

in the socket.

2 SATA optical drive installation ENWW

CAUTION: To prevent damage to this system, observe the following Electro Static Discharge (ESD)

precautions while performing the system parts removal/replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body

to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat,

static strap and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP workstation products. They have been extensively tested for

reliability and are manufactured to high quality standards. HP, therefore, warrants only those

accessories that are manufactured or sold by HP.

Electrostatic discharge

Discharge of static electricity from a finger or other conductor can damage system boards or other static-

sensitive devices. This type of damage could reduce the life expectancy of the device.

Preventing electrostatic damage

To prevent electrostatic discharge damage, observe the following precautions:

●Avoid hand contact by transporting and storing parts in static-safe containers.

●Keep electrostatic-sensitive parts in their containers until they arrive at static-free work areas.

●Place parts container on a grounded surface before removing parts from their container.

●Avoid touching pins, leads, or circuitry of parts or workstations.

●Always ensure you are properly grounded before touching an electrostatic-sensitive component or

assembly.

Grounding methods

There are several methods for grounding. Use one or more of the following measures when handling

or installing electrostatic-sensitive parts:

●Use a wrist strap connected by a ground cord to a grounded workstation chassis. Wrist straps are

flexible straps with a minimum of 1 meg. ohm +/- 10 percent resistance in the ground cords. To

provide a proper ground, wear the strap snug against the skin.

●Use heelstraps, toestraps, or bootstraps at standing workstations. Wear the straps on both feet

when standing on conductive floors or dissipating floor mats.

●Use conductive field service tools.

●Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of

the suggested equipment for proper grounding, have an authorized dealer, reseller, or service

provider install the part.

NOTE: For additional information on static electricity or for assistance with the installation of this

product, contact an authorized dealer, reseller, or service provider.

ENWW Electrostatic discharge 3

Configuration rules and assumptions when installing both

SATA and PATA optical disk drives in the same

workstation

This section provides information on the sequence in which the workstation detects and assigns ODD

IDs and drive letters when both SATA and PATA ODDs are installed on a workstation. It also provides

configuration rules that determine which SATA ports are functional and which ports can be used to

update system BIOS.

Drive detection and assignment sequence

When mixing PATA and SATA ODDs in a workstation, the PATA optical drive will always be detected

first by the system. For example, if the first ODD is a SATA drive and second ODD a PATA drive, the

system will detect the PATA ODD drive first. This will generally result in the PATA ODD being assigned

the lower drive ID or drive designation letter by the operating system.

Workstation SATA port configuration rules

Port configuration rules are determined individually by workstation product as shown in the following

subsection.

xw9400 Workstation BIOS configuration

When the xw9400 Workstation is set to RAID Mode in BIOS, any SATA ports that have an ODD

connected to them must have RAID turned off.

xw8400 Workstation, xw6400 Workstation, xw4400 Workstation, xw6600 Workstation,

and xw8600 Workstation SATA configuration mode settings

When the SATA Configuration Mode for these workstations is set to:

●Separate Mode - Only SATA ports 0, 1, 2, and 3 are functional for any SATA devices.

●Combined Mode - Only SATA ports 0 and 2 are functional for any SATA devices.

●RAID/AHCI Mode - You will not be able to update system BIOS from the SATA ODD.

●Combined Mode or Separate Mode - BIOS can be updated using a SATA ODD attached to

functional ports.

NOTE: The xw4550 Workstation and xw4600 Workstation do not support PATA optical disk drives.

Preparing for installation

Before beginning installation of the SATA ODD, ensure that the installation kit contains all necessary

items, that you have the required tools, that you understand the necessary precautions, and that you

have prepared the workstation, as described in the following subsections.

Tools required

You may need the following to install the optical drive:

●Torx T-15 screwdriver or flat-bladed screwdriver

4 SATA optical drive installation ENWW

Precautions for handling the drive and discs

Observe all precautions when handling the drive and discs, as listed below:

●Do not use worn, cracked, warped, or poor quality discs in the optical drive.

●Look for cracks in the clear plastic area in the center of the disc. If cracks are present, do not use

the disc in the optical drive.

●Do not affix any adhesive labels to the disc surface. Affixing an adhesive label on the disc can

cause damage to the disc and/or optical drive.

●Do not drop the disc or subject it to physical shock.

●Do not put the disc in a location subject to dust, direct sunlight, extreme temperatures, or high

humidity.

●Do not move the drive during operation. Doing so may cause it to malfunction during reading.

●Avoid exposing the drive to sudden changes in temperature, as condensation may form inside the

unit. If the temperature suddenly changes while the drive is on, wait at least one hour before you

remove the power. If you operate the unit immediately, it may malfunction while reading.

●Avoid placing the drive in a location that is subject to high humidity, extreme temperatures,

mechanical vibration, or direct sunlight.

●Keep the original packing materials for future transportation of the drive.

●Remove the disc before moving the drive.

●Clean the unit panel and controls with a soft, dry cloth, or a soft cloth lightly moistened with a mild

detergent solution. Never spray cleaning fluids directly on the unit.

●Do not clean the drive with solvents such as alcohol or benzene, which can damage the finish.

●If any object or liquid falls into the cabinet, immediately unplug the workstation and have it checked

by an authorized service provider.

●When a disc is not in use, remove it from the drive and store it in its case.

●Handle the disc by the edges, not the flat surface of the disc.

●Do not clean the disc with solvents such as alcohol, benzene, or antistatic spray, which can damage

the finish.

●Use only discs that are circular in shape. Do not use discs shaped in other forms, such as heart-

shaped or business card-shaped discs.

Preparing the workstation

Prepare the workstation for installation of the optical drive as follows (refer to the documentation provided

with the workstation for detailed instructions on the following operations):

1. Remove any diskette inserted in the diskette drive.

2. Turn off the workstation and any other peripheral devices.

3. Disconnect the AC power cord and any peripheral devices.

ENWW Preparing for installation 5

WARNING! To avoid the risk of serious injury or damage to the workstation, ensure that the power

cord is unplugged from the electrical outlet.

4. Remove the access panel from the workstation, then remove the front bezel by using the green

tabs.

WARNING! Allow the internal system to cool before touching in order to reduce the risk of

personal injury from hot surfaces.

Installing the drive

Complete the following steps to install the drive:

NOTE: Your workstation may not be identical to the workstation shown in the following illustrations. If

you need more information, refer to the documentation included with the workstation for drive installation

procedures.

NOTE: There may be drive length limitations for some of the drive bays in certain workstations.

1. Select a drive bay position on the workstation to install the new drive, as shown below.

NOTE: It is recommended that the next highest available bay be used when installing the new

drive.

Item Function

1CD/DVD drive

2Optical drive bay

3 Optical drive bay

6 SATA optical drive installation ENWW

CAUTION: Static electricity can damage the electronic components of the workstation or optional

equipment. Before beginning these procedures, ensure that you are static-free by briefly touching

a grounded metal object. In addition, avoid touching any exposed metal on the option board/chip

or on the workstation's circuit boards. Refer to the “Regulatory notices” section later in this

document for additional information.

2. Remove the flat bezel blank from the front bezel of the appropriate drive bay. The bezel blank is

the small panel that covers the drive bay opening when a drive is not installed in that bay.

3. Remove the EMI filler (if one is installed). The EMI filter is a thin metal piece blocking the bay

opening in order to reduce electromagnetic emissions.

4. If your optical drive requires guide screws, use the four M3 guide screws provided as part of the

installation kit. Install two M3 guide screws into each side of the drive, as shown below, using a

Torx T-15 screwdriver.

NOTE: Some workstations, such as the xw6400, xw8400, and xw9400 do not require these guide

screws.

5. Slide the optical drive completely into a drive bay so that the drive is secured. On some workstation

models, you will need to lift the spring-loaded latch on the left side of the optical drive cage while

sliding the new drive in place.

ENWW Installing the drive 7

CAUTION: Failure to ensure that the optical drive has been properly secured may cause damage

to the drive when moving the workstation.

NOTE: Refer to the documentation included with your workstation for specific instructions on

securing an optional drive.

6. As shown below, connect the workstation power supply power cable (1) to the drive. Then connect

the SATA interface cable (2) between the drive and the next available SATA connector on the

workstation system board.

NOTE: Although a general recommendation is to plug the right-angle connector into the system

board, either end of the interface cable (straight or right-angle connector) can be connected to the

drive. Select an interface cable from the kit that best fits the length and connector required by your

workstation.

NOTE: The SATA Optical Drive does not have an audio cable receptacle. To obtain audio

capability for this drive, refer to the “Enabling digital audio” section that follows.

8 SATA optical drive installation ENWW

NOTE: Refer to “Configuration rules and assumptions when installing both SATA and PATA

optical drives in the same workstation,” earlier in this document, for recommended SATA

configuration information.

7. Reassemble the workstation by reinstalling the front bezel and access panel, and then

reconnecting any peripheral devices to the workstation.

Enabling digital audio

This section provides the information required to enable digital audio for the drive, based on the

operating system in use.

Windows XP

When using Windows XP on your workstation, enable the disk drive digital audio capability as follows:

1. From the Control Panel double-click System.

2. Click the Hardware tab, then click Device Manager.

3. Double-click DVD/CD-ROM drives.

4. Right-click the appropriate optical drive, then click Properties.

5. Click the Properties tab, then click the Enable Digital CD Audio for this CD-ROM Device

checkbox.

6. Click OK.

Windows Vista Business

The ODD digital audio capability is enabled by default when using the Windows Vista Business operating

system.

Red Hat Enterprise Linux (RHEL)

When running Red Hat Enterprise Linux, use the utility XMMS to enable and configure the digital audio

capability for the SATA Optical Drive.

RHEL 3

When running RHEL3, go to the XMMS website at www.xmms.org and download the XMMS interface.

Follow the directions provided in order to enable digital audio for the SATA Optical Drive.

RHEL 4

When running RHEL 4, enable the audio as follows:

1. Enter the following command line to launch the XMMS interface:

# xmms

2. In the Audio Player window, click on the arrow in the upper-left corner.

3. In the resulting drop-down window, click Options, then Preferences.

4. In the Preferences window, click the Audio I/O Plugins tab, then select CD Audio Player.

ENWW Enabling digital audio 9

5. Select Configure, then click the Playmode radio button for Digital audio extraction.

6. Click OK.

NOTE: If this does not enable the audio, enter the command line:

# alsamixer

This will open a control window that includes audio channel volume controls. Use the arrow key to move

the cursor to the PCM slider, then use the “m” key to toggle PCM to the “on” position.

RHEL 5

The ODD digital audio capability is enabled by default when using RHEL 5.

Operating the drive

Identifying the controls

Item Components Functions

1Drive Activity Light Illuminates whenever the optical drive is reading information from the disc.

2Manual Eject Button Access Hole Provides access to the Manual Eject Button to manually release the disc tray

for opening.

3Disc Tray Holds the disc.

4Load/Unload Button Causes the drive to open and close the disc tray.

NOTE: The drive bezel and drive controls may not be identical to those shown.

Opening the tray manually

If you have exited the CD application and are unable to eject the disc with the Load/Unload Button, or

if right-clicking on the drive letter and selecting the eject function does not work, you can eject the disc

manually by completing the following steps:

1. Insert a straightened paper clip or a metal rod approximately 1.6 mm (1/16 inch) in diameter and

at least 34.9 mm (1 3/8 inches) in length into the Manual Eject Button Access Hole and push firmly

against the Manual Eject Button until the tray releases.

10 SATA optical drive installation ENWW

Otros manuales para Xw4550 - Workstation - 2 GB RAM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de HP

HP 88780B Manual de usuario

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Manual de usuario

HP 20/700 Guía de inicio rápido

HP StorageWorks 9100 - Extreme Data Storage... Manual de usuario

HP StorageWorks 1510i - Modular Smart Array Manual de usuario

HP Surestore Disk Array 12h - And FC60 Guía rápida

HP ES3-H Series Instrucciones de instalación

HP StorageWorks AF204A Guía de instalación

HP OmniBook 3100 - Notebook PC Manual de usuario

HP StorageWorks DAT 40i Manual de usuario

HP StorageWorks Ultrium 230 Manual

HP StorageWorks P4000 Series Manual de usuario

HP HDD Manual de usuario

HP nimblestorage CS235 Manual de usuario

HP P10000 Manual de usuario

HP 6100 Manual de usuario

HP Pocket Playlist Manual de usuario

HP Surestore Tape Library Model 6/100 Manual

HP StorageWorks 1000 - Modular Smart Array Manual de servicio

HP StorageWorks XP10000 - Disk Array Manual de usuario

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP VS80 - StorageWorks DLT VS 80 Tape Drive Manual de usuario

HP StorageWorks MSL5000 series Manual de usuario

HP Performance Optimized Datacenter 20c Manual

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario