HP MultiSeat ms6000 Manual de usuario

Computer Setup (F10) Utility Guide

HP Compaq MultiSeat ms6000 Desktop

Development Company, L.P. The

information contained herein is subject to

change without notice.

Microsoft, Windows, and Windows Vista are

either trademarks or registered trademarks

of Microsoft Corporation in the United States

and/or other countries.

The only warranties for HP products and

services are set forth in the express warranty

statements accompanying such products

and services. Nothing herein should be

construed as constituting an additional

warranty. HP shall not be liable for technical

or editorial errors or omissions contained

herein.

This document contains proprietary

information that is protected by copyright. No

part of this document may be photocopied,

reproduced, or translated to another

language without the prior written consent of

Hewlett-Packard Company.

Computer Setup (F10) Utility Guide

HP Compaq MultiSeat ms6000 Desktop

First Edition (November 2009)

Document Part Number: 593679-001

About This Book

This guide provides instructions on how to use Computer Setup. This tool is used to reconfigure and

modify computer default settings when new hardware is installed and for maintenance purposes.

WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily

harm or loss of life.

CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage

to equipment or loss of information.

NOTE: Text set off in this manner provides important supplemental information.

ENWW iii

iv About This Book ENWW

Table of contents

Computer Setup (F10) Utility

Computer Setup (F10) Utilities ............................................................................................................. 1

Using Computer Setup (F10) Utilities .................................................................................. 2

Computer Setup—File ......................................................................................................... 2

Computer Setup—Storage .................................................................................................. 3

Computer Setup—Security .................................................................................................. 6

Computer Setup—Power ..................................................................................................... 9

Computer Setup—Advanced ............................................................................................. 10

Recovering the Configuration Settings ............................................................................................... 13

ENWW v

vi ENWW

Computer Setup (F10) Utility

Computer Setup (F10) Utilities

Use Computer Setup (F10) Utility to do the following:

●Change factory default settings.

●Set the system date and time.

●Set, view, change, or verify the system configuration, including settings for processor, graphics,

memory, audio, storage, communications, and input devices.

●Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media

devices.

●Enable Quick Boot, which is faster than Full Boot but does not run all of the diagnostic tests run

during a Full Boot. You can set the system to:

❑

always Quick Boot (default);

❑

periodically Full Boot (from every 1 to 30 days); or

❑

always Full Boot.

●Select Post Messages Enabled or Disabled to change the display status of Power-On Self-Test

(POST) messages. Post Messages Disabled suppresses most POST messages, such as memory

count, product name, and other non-error text messages. If a POST error occurs, the error is

displayed regardless of the mode selected. To manually switch to Post Messages Enabled during

POST, press any key (except F1 through F12).

●Establish an Ownership Tag, the text of which is displayed each time the system is turned on or

restarted.

●Enter the Asset Tag or property identification number assigned by the company to this computer.

●Enable the power-on password prompt during system restarts (warm boots) as well as during

power-on.

●Establish a setup password that controls access to the Computer Setup (F10) Utility and the

settings described in this section.

●Secure integrated I/O functionality, including the serial, USB, or parallel ports, audio, or embedded

NIC, so that they cannot be used until they are unsecured.

●Enable or disable removable media boot ability.

●Solve system configuration errors detected but not automatically fixed during the Power-On Self-

Test (POST).

ENWW Computer Setup (F10) Utilities 1

●Replicate the system setup by saving system configuration information on USB flash media device

or other storage media emulating a diskette and restoring it on one or more computers.

●Execute self-tests on a specified ATA hard drive (when supported by drive).

●Enable or disable DriveLock security (when supported by drive).

Using Computer Setup (F10) Utilities

Computer Setup can be accessed only by turning the computer on or restarting the system. To access

the Computer Setup Utilities menu, complete the following steps:

1. Turn on or restart the computer.

2. As soon as the computer is turned on, press F10 when the monitor light turns green to enter

Computer Setup. Press Enter to bypass the title screen, if necessary.

NOTE: If you do not press F10 at the appropriate time, you must restart the computer and again

press F10 when the monitor light turns green to access the utility.

3. Select your language from the list and press Enter.

4. A choice of five headings appears in the Computer Setup Utilities menu: File, Storage, Security,

Power, and Advanced.

5. Use the arrow (left and right) keys to select the appropriate heading. Use the arrow (up and down)

keys to select the option you want, then press Enter. To return to the Computer Setup Utilities

menu, press Esc.

6. To apply and save changes, select File > Save Changes and Exit.

●If you have made changes that you do not want applied, select Ignore Changes and Exit.

●To reset to factory settings or previously saved default settings (some models), select Apply

Defaults and Exit. This option will restore the original factory system defaults.

CAUTION: Do NOT turn the computer power OFF while the BIOS is saving the Computer Setup (F10)

changes because the CMOS could become corrupted. It is safe to turn off the computer only after exiting

the F10 Setup screen.

Table 1 Computer Setup (F10) Utility

Heading Table

File Table 2 Computer Setup—File on page 3

Storage Table 3 Computer Setup—Storage on page 4

Security Table 4 Computer Setup—Security on page 6

Power Table 5 Computer Setup—Power on page 9

Advanced Table 6 Computer Setup—Advanced (for advanced users)

on page 10

Computer Setup—File

NOTE: Support for specific Computer Setup options may vary depending on the hardware

configuration.

2 Computer Setup (F10) Utility ENWW

Table 2 Computer Setup—File

Option Description

System Information Lists:

●Product name

●SKU number (some models)

●Processor type/speed/stepping

●Cache size (L1/L2)

●Installed memory size/speed, number of channels (single or dual) (if applicable)

●Integrated MAC address for embedded, enabled NIC (if applicable)

●System BIOS (includes family name and version)

●Chassis serial number

●Asset tracking number

●ME firmware version

●Management mode

About Displays copyright notice.

Set Time and Date Allows you to set system time and date.

Flash System ROM Allows you to update the system ROM with a BIOS image file located on a USB flash media device

or CD-ROM.

Replicated Setup Save to Removable Media

Saves system configuration, including CMOS, to a USB flash media device or a diskette-like device

(a storage device set to emulate a diskette drive).

Restore from Removable Media

Restores system configuration from a USB flash media device or a diskette-like device.

Default Setup Save Current Settings as Default

Saves the current system configuration settings as the default.

Restore Factory Settings as Default

Restores the factory system configuration settings as the default.

Apply Defaults and

Exit

Applies the currently selected default settings and clears any established passwords.

Ignore Changes

and Exit

Exits Computer Setup without applying or saving any changes.

Save Changes and Exit Saves changes to system configuration or default settings and exits Computer Setup.

Computer Setup—Storage

NOTE: Support for specific Computer Setup options may vary depending on the hardware

configuration.

ENWW Computer Setup (F10) Utilities 3

Table 3 Computer Setup—Storage

Option Description

Device Configuration Lists all installed BIOS-controlled storage devices.

When a device is selected, detailed information and options are displayed. The following options

may be presented:

Drive Emulation

Allows you to select a drive emulation type for a certain storage device. (For example, a Zip drive

can be made bootable by selecting diskette emulation.)

Emulation Type

ATAPI Zip drive:

●None (treated as Other).

●Diskette (treated as diskette drive).

CD-ROM: No emulation options available.

ATAPI LS-120:

●None (treated as Other).

●Diskette (treated as diskette drive).

Hard Disk:

●None (prevents BIOS data accesses and disables it as a boot device).

●Hard Disk (treated as hard disk).

Translation Mode (ATA disks only)

Lets you select the translation mode to be used for the device. This enables the BIOS to access

disks partitioned and formatted on other systems and may be necessary for users of older versions

of UNIX (e.g., SCO UNIX version 3.2). Options are Automatic, Bit-Shift, LBA Assisted, User, and

Off.

CAUTION: Ordinarily, the translation mode selected automatically by the BIOS should not be

changed. If the selected translation mode is not compatible with the translation mode that was active

when the disk was partitioned and formatted, the data on the disk will be inaccessible.

Translation Parameters (ATA disks only)

NOTE: This feature appears only when User translation mode is selected.

Allows you to specify the parameters (logical cylinders, heads, and sectors per track) used by the

BIOS to translate disk I/O requests (from the operating system or an application) into terms the hard

drive can accept. Logical cylinders may not exceed 1024. The number of heads may not exceed

256. The number of sectors per track may not exceed 63. These fields are only visible and

changeable when the drive translation mode is set to User.

SATA Default Values

Allows you to specify the default values for the Translation Mode for ATA devices.

4 Computer Setup (F10) Utility ENWW

Otros manuales para MultiSeat ms6000

Tabla de contenidos

Otros manuales de Software de HP

HP SN3000B Manual de usuario

HP ProLiant ML310 Generation 5p Manual de usuario

HP Integrity Superdome 2 16-socket Manual de instrucciones

HP Brocade 8/24c Manual de instrucciones

HP 500 G2 Manual de usuario

HP StorageWorks MSA 2/8 - SAN Switch Manual de usuario

HP Integrity BL860c Manual de usuario

HP Spooler FASTP Manual de usuario

HP Kayak XU700 Manual de usuario

HP StorageWorks 8B - FC Entry Switch Manual de usuario

HP cc2300 Manual de usuario

HP StorageWorks 2/64 - Core Switch Manual de usuario

HP Integrity rx2800 - i2 Guía de referencia rápida

HP T5145 - Thin Client - Tower Manual de servicio

HP StorageWorks 2000fc Manual de usuario

HP HP 2605dn Print Drivers Manual de servicio

HP HP-UX 11i v3 Manual de servicio

HP StorageWorks 2/32 - SAN Switch Manual de instrucciones

HP StorageWorks 4/8 - SAN Switch Manual de instrucciones

HP AK373A - StorageWorks All-in-One Storage System 1200r 5.4TB SAS Model NAS... Cómo utilizar

HP 345646-001 - StorageWorks NAS 2000s External Storage... Instrucciones de instalación y funcionamiento

HP BL680c - ProLiant - G5 Manual de usuario

HP SN6000B Manual de instrucciones

HP HPE XP P9500 Manual de usuario

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario

Novell

Novell SP2 - S Manual de instrucciones