HP 1660CS-Series Manual de usuario

About this Manual

We’ve added this manual to the Agilent website in an effort to help you support

your product. This manual is the best copy we could find; it may be incomplete

or contain dated information. If we find a more recent copy in the future, we will

add it to the Agilent website.

Support for Your Product

Agilent no longer sells or supports this product. Our service centers may be able

to perform calibration if no repair parts are needed, but no other support from

Agilent is available. You will find any other available product information on the

Agilent Test & Measurement website, www.tm.agilent.com.

HP References in this Manual

This manual may contain references to HP or Hewlett-Packard. Please note that

Hewlett-Packard's former test and measurement, semiconductor products and

chemical analysis businesses are now part of Agilent Technologies. We have

made no changes to this manual copy. In other documentation, to reduce

potential confusion, the only change to product numbers and names has been in

the company name prefix: where a product number/name was HP XXXX the

current name/number is now Agilent XXXX. For example, model number

HP8648A is now model number Agilent 8648A.

User’s Guide

Publication Number 01660-97017

First Edition, November 1995

For Safety Information, Warranties, and Regulatory Information, see the

pages at the end of this manual.

Copyright Hewlett-Packard Company 1991 - 1995

HP 1660CS-Series

Logic Analyzers

HP 1660CS-Series Logic Analyzers

The HP 1660CS-series logic analyzers are 100-MHz state/500-MHz

timing logic analyzers and 1 GSa/s digitizing oscilloscopes.

Logic Analyzer Features

•130 data channels and 6 clock/data channels in the HP 1660CS

•96 data channels and 6 clock/data channels in the HP 1661CS

•64 data channels and 4 clock/data channels in the HP 1662CS

•32 data channels and 2 clock/data channels in the HP 1663CS

•3.5-inch flexible disk drive and 540 MB hard disk drive

•HP-IB, RS-232-C, and Centronics interfaces

•Variable setup/hold time

•4 K memory on all channels with 8 K in half-channel mode

•Marker measurements

•12 levels of trigger sequencing for state and 10 levels of trigger

sequencing for timing

•100 MHz time tagging and number-of-states tagging

•Full programmability

•DIN mouse and keyboard support

Oscilloscope Features

•8000 samples per channel

•Automatic pulse parameters

displays time between markers, acquires until specified time

between markers is captured, performs statistical analysis on

time between markers

•Lightweight miniprobes

Options include Ethernet LAN Interface, Programmer’s Guide, and

Service Guide

In This Book

This User’s Guide shows you how to

use the HP 1660CS-series logic

analyzer. It contains measurement

examples, field and feature

definitions, and a basic service guide.

Refer to this manual for information

on what the menu fields do and how

they are used. This manual covers all

HP 1660CS-series analyzers.

The User’s Guide is divided into four

parts. The first part, chapters 1

through 4, covers general product

information you need to use the logic

analyzer. The second part, chapters

5 and 6, contains detailed examples

to help you use your analyzer in

performing complex measurements.

The third part, chapters 7 through 9,

contains reference information on the

hardware and software, including the

analyzer menus and how they are

used. There are sections for each

analyzer menu and a separate

chapter on System Performance

Analysis. The fourth part, chapters 10

through 12, provides a basic service

guide.

1The Logic Analyzer at a Glance

Connecting Peripherals

Using the Logic Analyzer

Triggering Examples

Using the Trigger Menu

File Management

Reference

System Performance Analysis

(SPA) Software

Concepts

Troubleshooting

Specifications

Operator’s Service

Glossary

Index

iii

Introduction

Contents

1 Logic Analyzer Overview

To make a measurement 1–4

2 Connecting Peripherals

To connect a mouse 2–3

To connect a keyboard 2–4

To connect to an HP-IB printer 2–5

To connect to an RS-232-C printer 2–7

To connect to a parallel printer 2–8

To connect to a controller 2–9

3 Using the Logic Analyzer

Accessing the Menus 3–3

To access the System menus 3–4

To access the Analyzer menus 3–6

To access the Scope menus 3–8

Using the Analyzer Menus 3–10

To label channel groups 3–10

To create a symbol 3–12

To examine an analyzer waveform 3–14

To examine an analyzer listing 3–16

To compare two listings 3–18

The Inverse Assembler 3–20

To use an inverse assembler 3–20

4 Using the Trigger Menu

Specifying a Basic Trigger 4–3

To assign terms to an analyzer 4–4

To define a term 4–5

To change the trigger specification 4–6

Changing the Trigger Sequence 4–7

To add sequence levels 4–8

To change macros 4–9

Setting Up Time Correlation between Analyzers 4–10

To set up time correlation between two state analyzers 4–11

To set up time correlation between a timing and a state analyzer 4–11

Arming and Additional Instruments 4–12

To arm another instrument 4–12

To arm the oscilloscope with the analyzer 4–13

To receive an arm signal from another instrument 4–15

Managing Memory 4–16

To selectively store branch conditions (State only) 4–17

To place the trigger in memory 4–18

To set the sampling rates (Timing only) 4–19

Contents

5 Triggering Examples

Single-Machine Trigger Examples 5–3

To store and time the execution of a subroutine 5–4

To trigger on the nth iteration of a loop 5–6

To trigger on the nth recursive call of a recursive function 5–8

To trigger on entry to a function 5–10

To capture a write of known bad data to a particular variable 5–11

To trigger on a loop that occasionally runs too long 5–12

To verify correct return from a function call 5–13

To trigger after all status bus lines finish transitioning 5–14

To find the nth assertion of a chip select line 5–15

To verify that the chip select line is strobed after the address is stable 5–16

To trigger when expected data does not appear when requested 5–17

To test minimum and maximum pulse limits 5–18

To detect a handshake violation 5–20

To detect bus contention 5–21

Cross-Arming Trigger Examples 5–22

To examine software execution when a timing violation occurs 5–23

To look at control and status signals during execution of a routine 5–24

To detect a glitch 5–25

To capture the waveform of a glitch 5–26

To view your target system processing an interrupt 5–27

To trigger timing analysis of a count-down on a set of data lines 5–28

To monitor two coprocessors in a target system 5–29

Special displays 5–30

To interleave trace lists 5–31

To view trace lists and waveforms on the same display 5–32

Contents

vii

6 File Management

Transferring Files Using the Flexible Disk Drive 6–3

To save a configuration 6–4

To load a configuration 6–6

To save a listing in ASCII format 6–7

To save a screen’s image 6–8

To load additional software 6–9

7 Reference

Configuration Capabilities 7–3

Probing 7–5

General-purpose probing system description 7–8

Oscilloscope probes 7–11

Assembling the probing system 7–12

Keyboard Shortcuts 7–16

Moving the cursor 7–16

Entering data into a menu 7–17

Using the keyboard overlays 7–17

Common Menu Fields 7–18

Print field 7–19

Run/Stop field 7–20

Roll fields 7–21

Disk Drive Operations 7–22

Disk operations 7–22

Autoload 7–24

Format 7–24

Pack 7–24

Load and Store 7–25

Contents

viii

The RS-232-C, HP-IB, and Centronics Interfaces 7–26

The HP-IB interface 7–27

The RS-232-C interface 7–27

The Centronics interface 7–28

System Utilities 7–29

Real Time Clock Adjustments field 7–29

Update FLASH ROM field 7–29

Shade adjustments 7–30

The Analyzer Configuration Menu 7–31

Type field 7–31

Illegal configuration 7–31

The Analyzer Format Menu 7–32

Pod threshold field 7–32

State. acquisition modes (state only) 7–32

Timing acquisition modes (timing only) 7–33

Clock Inputs display 7–34

Pod clock field (State only) 7–34

Master and Slave Clock fields (State only) 7–37

Symbols field 7–40

Label fields 7–41

Label polarity fields 7–42

The Analyzer Trigger Menu 7–43

Trigger sequence levels 7–43

Modify trigger field 7–43

Timing trigger macro library 7–44

State trigger macro library 7–46

Modifying the user macro 7–48

Resource terms 7–51

Arming Control field 7–54

Acquisition Control field 7–56

Count field (State only) 7–57

Contents

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario