HP E4418B Manual de usuario

HP4402.book : title.fm i Thu Feb 11 15:53:59 1999

HP Part no. E4418-90032

December, 1998

User’s Guide

HP E4418B Power Meter

HP4402.book : title.fm ii Thu Feb 11 15:53:59 1999

ii HP E4418B User’s Guide

written permission is prohibited, except as allowed under the copyright

laws.

Printed in the UK.

HP4402.book : title.fm iii Thu Feb 11 15:53:59 1999

Legal Information

HP E4418B User’s Guide iii

Legal Information

Notice

Information contained in this document is subject to change without

notice. Hewlett-Packard makes no warranty of any kind with regard to

this material, including, but not limited to, the implied warranties of

merchantability and ﬁtness for a particular purpose. Hewlett-Packard

shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishings, performance,

or use of this material. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written

consent of HP.

Certiﬁcation

Hewlett-Packard Company certiﬁes that this product met its published

speciﬁcations at the time of shipment from the factory. Hewlett-Packard

further certiﬁes that its calibration measurements are traceable to the

United States National Institute of Standards and Technology, to the

extent allowed by the Institute’s calibration facility, and to the calibration

facilities of other International Standards Organization members.

Warranty

This Hewlett-Packard instrument product is warranted against defects in

material and workmanship for a period of one year from date of shipment.

During the warranty period, Hewlett-Packard Company will at its option,

either repair or replace products which prove to be defective. For warranty

service or repair, this product must be returned to a service facility

designated by HP. Buyer shall prepay shipping charges to HP and HP

shall pay shipping charges, duties, and taxes for products returned to HP

from another country. HP warrants that its software and ﬁrmware

designated by HP for use with an instrument will execute its

programming instructions when properly installed on that instrument.

HP does not warrant that the operation of the instrument, or ﬁrmware

will be uninterrupted or error free.

HP4402.book : title.fm iv Thu Feb 11 15:53:59 1999

Legal Information

iv HP E4418B User’s Guide

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper

or inadequate maintenance by Buyer, Buyer-supplied software or

interfacing, unauthorized modiﬁcation or misuse, operation outside of the

environmental speciﬁcations for the product, or improper site preparation

or maintenance. NO OTHER WARRANTY IS EXPRESSED OR IMPLIED.

HP SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER’S SOLE AND

EXCLUSIVE REMEDIES. HP SHALL NOT BE LIABLE FOR ANY

DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY

OTHER LEGAL THEORY.

HP4402.book : title.fm v Thu Feb 11 15:53:59 1999

Equipment Operation

HP E4418B User’s Guide v

Equipment Operation

Warnings and Cautions

This guide uses warnings and cautions to denote hazards.

WARNING A warning calls attention to a procedure, practice or the

like, which, if not correctly performed or adhered to, could

result in injury or the loss of life. Do not proceed beyond a

warning until the indicated conditions are fully

understood and met.

Caution A caution calls attention to a procedure, practice or the like which,

if not correctly performed or adhered to, could result in damage to

or the destruction of part or all of the equipment. Do not proceed

beyond a caution until the indicated conditions are fully

understood and met.

Personal Safety Considerations

WARNING This is a Safety Class I product (provided with a protective

earthing ground incorporated in the power cord). The

mains plug shall only be inserted in a socket outlet

provided with a protective earth contact. Any interruption

of the protective conductor, inside or outside the

instrument, is likely to make the instrument dangerous.

Intentional interruption is prohibited.

If this instrument is not used as speciﬁed, the protection

provided by the equipment could be impaired. This

instrument must be used in a normal condition (in which

all means of protection are intact) only.

No operator serviceable parts inside. Refer servicing to

qualiﬁed personnel. To prevent electrical shock, do not

remove covers.

For continued protection against ﬁre hazard, replace the

line fuse(s) only with fuses of the same type and rating (for

example, normal blow, time delay, etc.). The use of other

fuses or material is prohibited.

HP4402.book : title.fm vi Thu Feb 11 15:53:59 1999

General Safety Considerations

vi HP E4418B User’s Guide

General Safety Considerations

WARNING Before this instrument is switched on, make sure it has

been properly grounded through the protective conductor

of the ac power cable to a socket outlet provided with

protective earth contact.

Any interruption of the protective (grounding) conductor,

inside or outside the instrument, or disconnection of the

protective earth terminal can result in personal injury.

Caution Any adjustments or service procedures that require operation of

the instrument with protective covers removed should be

performed only by trained service personnel.

Markings

The CE mark shows that the product complies with

all the relevant European legal Directives (if

accompanied by a year, it signiﬁes when the design

was proven.

This is the symbol of an Industrial Scientiﬁc and

Medical Group 1 Class A product.

The CSA mark is a registered trademark of the

Canadian Standards Association.

External Protective Earth Terminal.

While this is a Class I product, provided with a

protective earthing conductor in a power cord, an

external protective earthing terminal has also been

provided. This terminal is for use where the earthing

cannot be assured. At least an 18AWG earthing

conductor should be used in such an instance, to

ground the instrument to an assured earth terminal.

ISMGROUP 1

CLASS A

HP4402.book : title.fm vii Thu Feb 11 15:53:59 1999

General Safety Considerations

HP E4418B User’s Guide vii

IEC 1010-1 Compliance

This instrument has been designed and tested in accordance with IEC

Publication 61010-1 +A1:1992 Safety Requirements for Electrical

Equipment for Measurement, Control and Laboratory Use and has been

supplied in a safe condition. The instruction documentation contains

information and warnings which must be followed by the user to ensure

safe operation and to maintain the instrument in a safe condition.

Statement of Compliance

This product has been designed and tested for compliance with IEC 60529

(1989) Degrees of Protection Provided by Enclosures (IP Code). Level IPx4

is attained if, and only if, the carry case( part number HP 34141A) is

ﬁtted.

User Environment

This product is designed for use in a sheltered environment (avoiding

extreme weather conditions) in accordance with Pollution Degree 3

deﬁned in IEC 60664-1, with the carry case ( part number HP 34141A)

ﬁtted over the instrument.

The product is suitable for indoor use only, when this carry case is not

ﬁtted.

Installation Instructions

To avoid unnecessary over-temperature conditions, while this carry case is

ﬁtted do not apply an ac mains supply voltage, only operate your

HP E4418B from the battery pack.

HP4402.book : title.fm viii Thu Feb 11 15:53:59 1999

Regulatory Information

viii HP E4418B User’s Guide

Regulatory Information

Sound Emission

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der

Maschinenlarminformationsverordnung vom 18 Januar 1991.

• Sound Pressure LpA < 70 dB.

• Am Arbeitsplatz.

• Normaler Betrieb.

• Nach DIN 45635 T. 19 (Typprufung).

Manufacturers Declaration

This statement is provided to comply with the requirements of the

German Sound DIN 45635 T. 19 (Typprufung).

• Sound Pressure LpA < 70 dB.

• At operator position.

• Normal operation.

• According to ISO 7779 (Type Test).

Australian EMC Regulations

The C-Tick mark is a registered trademark of the Spectrum Management

Agency of Australia. This signiﬁes compliance with the Australian EMC

Framework Regulations under the terms of the Radiocommunications Act

of 1992.

HP4402.book : title.fm ix Thu Feb 11 15:53:59 1999

Regulatory Information

HP E4418B User’s Guide ix

Europe Contact:

Your local Hewlett-Packard Sales and Service Ofﬁce or Hewlett-Packard GmbH, Department 2Q /

Standards Europe, Herrenberger Strasse 130, D7030 Boblinger (Fax; +49-7031-143143).

Declaration of Conformity

according to ISO/IEC Guide 22 and EN45014

Manufacturer’s Name: Hewlett Packard Ltd.

Manufacturer's Address: Queensferry Microwave Division

South Queensferry

West Lothian, EH30 9TG

Scotland, United Kingdom

Declares that the product

Product Name:Single Channel Power Meter

Model Numbers: HP E4418B

Product Options: This declaration covers all options of the above products as detailed in

TCF A-5951-9852-02

Conforms with the protection requirements of European Council Directive 89/336/EEC on the approximation

of the laws of the member states relating to electromagnetic compatibility.

Against EMC test speciﬁcations EN 55011:1991 (Group 1, Class A) and EN 50082-1:1992

As Detailed in: Electromagnetic Compatibility (EMC)

Technical Construction File (TCF) No. A-5951-9852-01

Assessed by: Dti Appointed Competent Body

EMC Test Centre,

GEC-Marconi Avionics Ltd.,

Maxwell Building,

Donibristle Industrial Park,

KY11 5LB

Scotland, United Kingdom

Technical Report Number:6893/2200/CBR, dated 23 September 1997

Supplementary Information: The product conforms to the following safety standards

EN61010-1 (1993) / IEC 1010-1 (1990) + A1 (1992)

CSA-C22.2 No. 1010.1-92

EN60825-1 (1994) / IEC 825-1 (1993)

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC, and carries the

CE-marking accordingly. This product is also designed to meet IPx4 in accordance with IEC 60529:1989 / EN

60529:1992.

South Queensferry, Scotland 22 October 1998

Location Date R.M. Evans / Quality Manager

HP4402.book : title.fm x Thu Feb 11 15:53:59 1999

List of Related Publications

x HP E4418B User’s Guide

List of Related Publications

The HP E4418B User’s Guide is also available in the following languages:

• English Language User’s Guide - Standard

• German Language User’s Guide - Option ABD

• Spanish Language User’s Guide - Option ABE

• French Language User’s Guide - Option ABF

• Italian Language User’s Guide - Option ABZ

• Japanese Language User’s Guide - Option ABJ

HP E4418B/E4419B Programming Guide is shipped as standard.

HP E4418B/E4419B Service Guide is available by ordering Option 915.

HP E4418B/E4419B CLIPs (Component Location and Information Pack)

is available by ordering E4418-90031.

Useful information on SCPI (Standard Commands for Programmable

Instruments) can be found in:

•A Beginner’s Guide to SCPI, which is available by ordering

HP Part Number 5010-7166.

• The SCPI reference manuals which are available from:

SCPI Consortium,

8380 Hercules Drive, Suite P3,

La Mesa, CA 91942, USA.

Telephone: 619-697-4301

Fax: 619-697-5955

Otros manuales para E4418B

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario