HP HP 70909A Manual de usuario

Installation Guide

HP 70909A and HP 70910A

RF Section

ABCDE

HP Part No. 70909-90002

Printed in USA April 1993

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material, including,

but not limited to, the implied warranties of merchantability and tness for a particular

purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Restricted Rights Legend.

Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth

in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

DFARS 252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the Commercial

Computer Software Restricted Rights clause at FAR 52.227-19 for other agencies.



is prohibited, except as allowed under the copyright laws

1400 Fountaingrove Parkway, Santa Rosa, CA 95403-1799, USA

Certication

Hewlett-Packard Company certies that this product met its published specications at the

time of shipment from the factory. Hewlett-Packard further certies that its calibration

measurements are traceable to the United States National Institute of Standards and

Technology, to the extent allowed by the Institute's calibration facility, and to the calibration

facilities of other International Standards Organization members.

Warranty

This Hewlett-Packard instrument product is warranted against defects in material and

workmanship for a period of one year from date of shipment. During the warranty period,

Hewlett-Packard Company will, at its option, either repair or replace products which prove to

be defective.

For warranty service or repair, this product must be returned to a service facility designated by

Hewlett-Packard. Buyer shall prepay shipping charges to Hewlett-Packard and Hewlett-Packard

shall pay shipping charges to return the product to Buyer. However, Buyer shall pay all

shipping charges, duties, and taxes for products returned to Hewlett-Packard from another

country.

Hewlett-Packard warrants that its software and rmware designated by Hewlett-P

ackard for

use with an instrument will execute its programming instructions when properly installed on

that instrument. Hewlett-Packard does not warrant that the operation of the instrument, or

software, or rmware will be uninterrupted or error-free.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate

maintenance by Buyer, Buyer-supplied software or interfacing, unauthorized modication or

misuse, operation outside of the environmental specications for the product, or improper

site preparation or maintenance.

NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. HEWLETT-PACKARD SPECIFICALLY

DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE.

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER'S SOLE AND EXCLUSIVE REMEDIES.

HEWLETT-PACKARD SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT,

OR ANY OTHER LEGAL THEORY.

Assistance

Product maintenance agreements and other customer assistance agreements are available for

Hewlett-Packard products.

For any assistance, contact your nearest Hewlett-Packard Sales and Service Oce.

iii

Safety Symbols

The following safety symbols are used throughout this manual. Familiarize yourself with each

of the symbols and its meaning before operating this instrument.

Caution

The

caution

sign denotes a hazard. It calls attention to a procedure which, if

not correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a

caution

sign until the indicated

conditions are fully understood and met.

Warning

The

warning

sign denotes a hazard. It calls attention to a procedure

which, if not correctly performed or adhered to, could result in injury

or loss of life. Do not proceed beyond a

warning

sign until the indicated

conditions are fully understood and met.

General Safety Considerations

Warning

Before this instrument is switched on

, make sure it has been properly

grounded through the protective conductor of the ac power cable to a

socket outlet provided with protective earth contact.

Any interruption of the protective (grounding) conductor, inside or

outside the instrument, or disconnection of the protective earth terminal

can result in personal injury.

Warning

There are many points in the instrument which can, if contacted, cause

personal injury. Be extremely careful.

Any adjustments or service procedures that require operation of the

instrument with protective covers removed should be performed only by

trained service personnel.

Caution

Before this instrument is switched on,

make sure its primary power circuitry

has been adapted to the voltage of the ac power source.

Failure to set the ac power input to the correct voltage could cause damage to

the instrument when the ac power cable is plugged in.

Installation at a Glance

The HP 70909A RF section and HP 70910A RF section are preselected microwave front-end

modules that are used in an HP 70000 Series modular spectrum analyzer system. A standard

modular spectrum analyzer system includes an RF section, IF section, local oscillator,an

optional display, and an optional precision frequency reference.

Equipment and documentation supplied

This package contains:

HP 70909A RF section or HP 70910A RF section

HP 71209A Quick Start Guide

HP 70909A and HP 70910A Installation Guide

Rear panel cabling for your new RF section

Tools needed

Before installation, assemble these tools:

A long or short 8 mm hex-ball driver

A nonconductive stylus, such as a toothpick or similar object, for setting address switches

Antistatic precautions

Electrical components are easily damaged by small amounts of static electricity. If possible,

work at a static-safe work station.

Installation overview

The installation procedure for the HP 70909A or HP 70910A RF section is straightforward. The

following major steps are included:

Step 1. Switch o the system's ac line power

Step 2. Disconnect the existing RF section's rear panel cables

Step 3. Remove the existing RF section

Step 4. Unpack your new RF section

Step 5. Check or set the HP-MSIB address on your new RF section

Step 6. Install your new RF section

Step 7. Connect the new RF section's rear panel cables

Step 8. Switch on the system's ac line power

Step 9. Check proper operation of your new RF section

vii

In This Book

This book describes all of the installation procedures neccessary to install and check the

proper operation of either an HP 70909A RF section or an HP 70910A RF section in an

HP 70000 Series modular spectrum analyzer system. It also contains information on what to do

if problems occur during installation.

Each module in the HP 70000 Series modular spectrum analyzer system is shipped with its own

installation guide.For further information related to the installation of additional and alternate

modules that can be used in this system, refer to that module's installation guide.

Chapter 1 of this book presents step-by-step instructions that are required for proper

installation of either an HP 70909A or HP 70910A RF section in an HP 70000 Series modular

spectrum analyzer system.

Chapter 2 of this book presents information to help identify and resolve problems that may

occur with the installation of your HP 70909A or HP 70910A RF section.

For information on setting the HP-MSIB address switches of an HP 70909A or HP 70910A

RF section, refer to the

HP 70000 Modular Spectrum Analyzer Installation and Verication

Manual

viii

Contents

1. Installation

Step 1. Switch o the system's ac line power .... .. .. .. .. .. .. . 1-2

Step 2. Disconnect the existing RF section's rear panel cables ......... 1-3

Step 3. Remove the existing RF section . . . . . . . . . . . . . . . . . . . . 1-4

Step 4. Unpack your new RF section .. .. .. .. .. .. .. .. .. .. . 1-5

Step 5. Check or set the HP-MSIB address on your new RF section . . . . . . . 1-6

Step 6. Install your new RF section . . . . . . . . . . . . . . . . . . . . . . 1-7

Step 7. Connect the new RF section's rear panel cables .... .. .. .. .. 1-8

Step 8. Switch on the system's ac line power ................. 1-9

Step 9. Check proper operation of your new RF section ............ 1-10

2. If you have problems with installation

If the system's power-on self test fails .... .. .. .. .. .. .. .. . . 2-2

If your RF section is powered on but not responding correctly .... .. .. . 2-4

If the STATUS ERR indicator LED on your new RF section is ashing . . . . . . 2-5

If more than one module's error indicator is ashing . . . . . . . . . . . . . . 2-6

If hardware errors messages occur ...................... 2-7

If you require additional technical resources . . . . . . . . . . . . . . . . . . 2-9

Before calling or returning your RF section for service . . . . . . . . . . . . 2-9

Calling Hewlett-Packard for service . . . . . . . . . . . . . . . . . . . . . 2-9

Returning your equipment for service . . . . . . . . . . . . . . . . . . . . 2-11

Contents-1

Figures

2-1. Line Voltage Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2-2. Line Fuse Removal and Replacement .................... 2-2

Tables

2-1. Hewlett-Packard Sales and Service Oces . . . . . . . . . . . . . . . . . . 2-10

2-2. Packaging and Contents .......................... 2-12

Contents-2

Otros manuales para HP 70909A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de HP

HP 70427A Manual de usuario

HP HP 81531A Manual de usuario

HP HP 81554SM Manual del propietario

HP HP 85091A Manual de usuario

HP Synergy 480 Gen10 Manual de usuario

HP StorageWorks MSL6000 series Manual de usuario

HP HPE FM 2072 Manual de usuario

HP 75000 B Series Manual de usuario

HP 83481A Manual de usuario

HP Synergy 480 Gen9 Manual de usuario

HP 3484A Manual de servicio

HP 6600-A FIP-600 FlexIntfPltfrm Rtr Mod Instrucciones de montaje

HP E1328A Manual de usuario

HP ProCurve Wireless 170wl Manual de usuario

HP ProCurve PCM+ Agent on ONE zl Module Instrucciones de montaje

HP 572018-B21 Manual de usuario

HP HPE FlexNetwork 7500 Manual de usuario

HP SIC-4G-LTE-V Manual de usuario

HP HP 81536A Manual de usuario

HP 81541MM Manual del propietario

HP E3456A Manual de usuario

HP E2261A Manual de usuario

HP 3497A Manual de instalación

HP 7500 48p 1000BASE-T w/PoE+ SE Mod Instrucciones de instalación

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario