Honeywell WebStat T7350 Manual de usuario

INSTALLATION INSTRUCTIONS

62-0195-04

T7350 Commercial Programmable

Thermostat

FOR SINGLE- OR MULTI-STAGE CONVENTIONAL/HEAT PUMP

SYSTEMS

APPLICATION

The T7350 Commercial Programmable Thermostat

controls 24 Vac commercial single zone heating,

ventilating and air conditioning (HVAC) equipment. The

T7350 consists of a thermostat and subbase. The

thermostat includes the display and keypad for 7-day

programming. The subbase includes equipment control

connections. The subbase mounts on the wall and the

thermostat mounts to the subbase.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of an old control. If you have

questions, call Honeywell Customer Care Center

at 1-800-468-1502.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

them could damage the product or cause a hazard-

ous condition.

2. Check ratings given in instructions and on the

product to ensure the product is suitable for your

application.

3. Installer must be a trained, experienced service

technician.

4. After installation is complete, check out product

operation as provided in these instructions.

CAUTION

Electrical Shock or Equipment Damage

Hazard.

Can shock individuals or short equipment

circuitry.

Disconnect power supply before installation.

Location

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

IMPORTANT

To avoid electrical interference, which can

cause erratic performances, keep wiring runs as

short as possible and do not run thermostat

wires adjacent to the line voltage electrical dis-

tribution systems. Use shielded cable. The

cable shield must be grounded only at the con-

trolled equipment case.

Subbase

WHEN USED TO SENSE ROOM TEMPERATURE

Install the thermostat about 5 ft. (1.5m) above the floor in

an area with good air circulation at average temperature.

(See Fig. 1.)

WHEN NOT USED TO SENSE ROOM TEMPERATURE

When using the remote-mounted temperature (and

humidity) sensor(s) to sense ambient conditions, install

the thermostat in an area that is accessible for setting

and adjusting the temperature and settings.

CAUTION

Equipment Damage Hazard.

Can damage the TIM connection beyond

repair.

Disconnect the TIM cable prior to opening or

closing the thermostat cover.

NOTE: Allow sufficient clearance below the thermostat

to plug in the TIM cable.

Install the remote-mounted sensor(s) about 5 ft. (1.5m)

above the floor in an area with good air circulation at

average temperature. (See Fig. 1.)

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

62-0195—04 2

If multiple remote sensors are required, they must be

arranged in a temperature averaging network consisting

of four sensors. (See Fig. 2.)

NOTE: Only T7770 models with no setpoint adjustment

can be used for temperature averaging.

Fig. 1. Typical location of thermostat

or remote-mounted sensor.

Mounting Subbase

The subbase mounts horizontally.

IMPORTANT

• When using the internal temperature or humidity

sensor, the device must be mounted horizontally

(with the LCD facing upwards). Precise leveling

is not needed.

• When using remote room temperature and

humidity sensors, thermostat mounting orienta-

tion does not matter.

Wall mounting (using standard drywall screws) is

standard. Mounting to a 2 in. by 4 in. (50.8 mm by 101.6

mm) wiring box can be accomplished:

— for a horizontal box, no extra hardware is required.

— for a vertical box, part 209651A is required.

— Mount to European standard wall box (having 2.4 in.

(60.3 mm) between mounting screws in a horizontal

line) with or without adaptive hardware.

1. Position and level the subbase.

NOTE: A level wallplate is only for appearance.

The thermostat functions properly when

not level.

2. Use a pencil to mark the mounting holes.

(See Fig. 3.)

3. Remove the subbase from the wall and drill two

3/16 in. (4.8 mm) holes in the wall (if drywall) as

marked. For firmer material such as plaster or

wood, drill two 7/32 in. (5.6 mm) holes.

4. Gently tap anchors (provided) into the drilled holes

until flush with the wall.

5. Position the subbase over the holes, pulling wires

through the wiring opening.

6. Loosely insert the mounting screws into the holes.

7. Tighten mounting screws.

Fig. 2. Four T7770A Sensors providing temperature

averaging network for T7350 Thermostat.

Fig. 3. Mounting the subbase.

Mounting Thermostat on Subbase (Fig. 4)

With the subbase installed, mount the thermostat:

1. Engage top subbase tabs into the thermostat top.

2. Swing the thermostat down.

3. Press the lower edge of the case to latch.

NOTE: To remove the thermostat from the wall, first pull

out at the bottom of the thermostat; then remove

the top.

5 FEET

(1.5 METERS)

YES NO

NO NO

M4823A

M19606A

T4 T3

SUBBASE

T7770A

WIRES THROUGH WALL

WALL

ANCHORS

(2)

M19608

MOUNTING

HOLES

MOUNTING

SCREWS

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

3 62-0195—04

Fig. 4. Mounting thermostat on subbase.

Wiring

Follow equipment manufacturer wiring instructions when

available. Refer to the Wiring Diagram section for typical

hookups. A letter code is located near each terminal for

identification.

IMPORTANT

All wiring must comply with local electrical codes

and ordinances.

NOTE: Maximum (and recommended) wire size is 18-

gauge. Do not use wire smaller than 22-gauge.

1. Loosen subbase terminal screws and connect

system wires.

2. Securely tighten each terminal screw.

3. Push excess wire back into the hole in the wall.

4. Plug the hole with nonflammable insulation to

prevent drafts from affecting the thermostat.

SETTINGS

Using Thermostat Keys

The thermostat keys are used to:

• set current time and day,

• program times and setpoints for heating and cooling,

• override the program temperatures,

• display present setting,

• set system and fan operation,

• perform simple configuration.

NOTE: See Fig. 5 for keypad information.

Setting Temperature

Refer to Table 2 for the default temperature setpoints. See

the Product Data (form 63-2605) for complete instructions

on changing the setpoints.

Setting System and Fan

System default setting is Auto. Fan default setting is On.

NOTE: Use System and Fan keys to change settings.

System Settings

— Auto: Thermostat automatically changes between

heating and cooling based on indoor temperature.

— Cool: Thermostat controls cooling.

— Off: Heating, cooling, and fan are all off.

— Heat: Thermostat controls heating.

— Em Heat: Auxiliary heat serves as first stage.

Compressor stages are locked off.

Fan Settings

— On: See Table 1.

— Auto: Fan always cycles with call for heat or cool.

— Conventional: The equipment (i.e. plenum switch)

controls fan operation in heat mode. Thermostat

controls fan operation in cool mode.

— Electric Heat: Thermostat controls fan operation in

both heat and cool modes.

NOTES: Fan operation can extend (delay Off) after the

heating/cooling turns off:

— Heating choices are 0 or 90 seconds.

— Cooling choices are 0 or 40 seconds.

Table 1. Fan On Control Logic.

aIn heat mode, when set for conventional heat, the equip-

ment (i.e. plenum switch) could power the fan despite

the T7350.

M19609

PRESS LOWER EDGE OF CASE TO LATCH.

ENGAGE TABS AT TOP OF THERMOSTAT AND SUBBASE OR WALLPLATE.

Occupancy Call for Heat/Cool

Scheduled Sensor Signal Yes No

Occupied Occupied On On

Occupied Unoccupied On Off a

Standby *Doesn’t Matter On Off a

Not Occupied *Doesn’t Matter On Off a

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

62-0195—04 4

Fig. 5. Thermostat key locations.

INSTALLER SETUP

For most applications, the thermostat factory settings do

not need to be changed. Review the factory settings in

Table 2.

NOTE: When power is first applied to the thermostat, the

display will show all segments (see Fig. 6).

Table 2. Default Setpoints.

Fig. 6. LCD display of all segments.

CAUTION

Possible Equipment Damage.

Fan must be running when system is

operating.

Heat pump and electric heat systems must be

configured correctly to prevent equipment damage

caused by the system running without the fan.

Setup Using Keypad

The installer uses the Installer Setup to customize the

thermostat to specific systems. For basic setup functions,

the thermostat can be configured using the keypad.

NOTE: The T7350 has serial communications to

facilitate use of an installer configuration tool.

More advanced features are available using this

tool. (Refer to form 63-2605 for details.)

A combination of key presses are required to use the

Installer Setup feature:

1. To enter the Installer Setup, press and hold both the

Run Schedule and the Copy keys until DEG F (or

DEG C) displays.

2. To advance to the next Installer Setup number,

press .

NOTE: Pressing Run/Copy again while in this

mode displays the T7350 firmware version

number.

3. To return to a Setup item, cycle through the options.

4. To change a setting, use the up Sor down Tkey.

5. To exit the Installer Setup, press Run Schedule.

6. Display prompts SAV CFG (save configuration).

a. If you want to save the new configuration, use

the up Sor down Tkey to change NO to YES

before pressing Run Schedule.

b. If you want the configuration to remain as it was

before starting this change, ensure the

display indicates SAV CFG NO and press Run

Schedule.

NOTE: Installer Setup is automatically exited after five

minutes with no key pressed. Upon this auto-

matic exit, all changes are lost.

Configuration

Limited configuration can be done with the keypad using

the Configuration ID. In order to determine the proper

codes to use for the Configuration Variables (CnfgID).

NOTE: Spreadsheets of the CnfgID values are available

online at http://customer.honeywell.com

The PDA T7350 Configuration Tool or the PC Tool

LonSpec can also be used as follows:

1. Open the PDA Config Tool Application.

2. Select the desired configuration.

3. On the summary screen, tap CnfgID.

4. The PDA determines the proper CnfgID.

5. Make note of the values.

6. Press both Copy and Run Schedule.

7. Tap until C1 appears on the right end of the dis-

play.

NOTE: While stepping toward C1, check other

items to ensure they are set properly. See

Setup Using Keypad section.

8. To adjust each variable to match PDA indication:

a. Hold down the up Sor down Tkey to adjust

the value quickly.

b. Tap the up Sor down Tkey for fine control.

9. Tap to switch to another variable.

10. Return to step 8 and repeat the process until all

configuration values are set properly.

11. To exit the Installer Setup, press Run Schedule.

System Fan Run

Schedule

CopyNot OccupiedOccupiedDay

Clear

Start Time

Day Time

Temperature

Temporary

Occupied

Override

HEAT HEATCOOL COOL

HEAT COOL ON AUTO

Schedule

Set Day/Time

Occupied

Not Occupied

Temporar y

Not Occupied

M19610

Control Occupied Not Occupied Standby

Heating 70°F (21°C) 55°F (13°C) 67°F (19°C)

Cooling 75°F (24°C) 85°F (29°C) 78°F (26°C)

TemporaryStandby

StartTime

M19611

Not Occupied12

System

EmHeat Off CoolAuto

MonTueWedThuFri

SatSunHol

Dehumid OnAuto

MinsDays

Room

Fan

Set ScheduleSet

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

5 62-0195—04

12. Display prompts SAV CFG (save configuration).

a. If you want to save the new configuration, use

the up Sor down Tkey to change NO to YES

before pressing Run Schedule.

b. If you want the configuration to remain as it was

before starting this change, ensure the

display indicates SAV CFG NO and press Run

Schedule.

Setting Keypad Lockout

Proper keypad sequences activate the lockout features.

To change the keypad lockout state:

1. Enter the Installer Setup: press and hold both the

Run Schedule and the Copy keys until DEG F (or

DEG C) displays.

2. Press until KYLCK displays.

3. Use the up Sor down Tkey to change the setting.

Options are:

• 0: No lockout.

• 1: Lockout all keys except Temporary Occupied,

Temporary Not Occupied, up S, down Tand

• 2: Lockout all keys except .

NOTES:

— Options 1 and 2 do not allow adjustments on

dehumidification high limit.

— No options lockout special keypress func-

tions. See the Special Functions section for

details.

4. Once the proper option is chosen, exit Installer

Setup by pressing Run Schedule.

5. Display prompts SAV CFG. If you want to save it,

use the up Sor down Tkey to change NO to YES

before pressing Run Schedule again.

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

62-0195—04 6

Table 3. T7350 Key Function Summary.

aOn: Continuous fan operation (occupied and standby). During not occupied periods, fan cycles with call for heat or

cool.

Auto: Fan cycles with call for heat or cool during all periods. (See Product Data Sheet, form 63-2605, for more

details.)

NOTES: The display returns to default screen after pressing Run Schedule (or after a period of time without keypress):

— ten seconds: when returning from temporary setpoint changes, info screen, temp occ, and temp not occ.

— one minute: when returning from setting clock/day.

— ten minutes: when returning from System Checkout.

— five minutes: when returning from all other modes.

Grouping Button Definition

Information Down Arrow Lowers setpoint, day, or time. When setting times or temperatures, hold key

down to continuously decrease value. Also can make temporary change in

temperature setpoint.

Information Obtains information (where humidity “high-limit” can be set), cycles through

setup options.

Up Arrow Raises setpoint, day, or time. When setting times or temperatures, hold key

down to continuously increase value. Also can make temporary change in

temperature setpoint.

Temperature Occupied

Heat

Sets Occupied Heat setpoint.

Occupied

Cool

Sets Occupied Cool setpoint.

Not Occupied

Heat

Sets Not Occupied Heat setpoint.

Not Occupied

Cool

Sets Not Occupied Cool setpoint.

Set Day Sets day of week. Tapping key with 'Set Value' segment on increases current

day (same effect as Up Arrow key).

Time Sets time. Tapping key with “Set Value” segment on increases time in one hour

increments.

Override Temporary

Occupied

Temporary occupied setting for length of time defined by installer. User can

modify setpoints.

Temporary Not

Occupied

Sets holiday length. User selects number of days (“0”-”99”), or “---” for

continuous override.

Schedule Day Selects day schedule to modify. (Used also with copy key.)

Occupied Selects occupied event start times for specified day. Repeatedly press this key

to toggle between two occupied events.

Not Occupied Selects not occupied event start times for specified day. Repeatedly press this

key to toggle between two not occupied events.

Clear Start Time Clears start time for specified period and day.

Copy Copies schedule from one day to another.

System Selects System Mode. Toggles through Em Heat, Heat, Off, Cool, and Auto.

Fan Selects fan operation mode. Toggles between On and Auto.a

Run Schedule Resumes running schedule (cancels Temporary Occupied action, Holiday, and/

or Temporary setpoint changes.)

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

7 62-0195—04

Special Functions

Restore Factory Configuration (Run/Clear)

IMPORTANT

This operation erases current configuration and

restores factory defaults for all configuration,

parameters, setpoints and schedules. To regain

the old requires device reconfiguration.

1. Press both Run Schedule and Clear Start Time.

2. The display gives the option to revert to FAC CFG.

a. To restore the factory defaults, press up Sor

down Tuntil the display indicates YES.

b. To cancel this option, ensure the display

indicates NO.

3. Press Run Schedule.

Get Factory Schedule (Info/Clear)

Performing this operation reverts the schedules to the

factory defaults:

1. Press both Info and Clear Start Time.

2. The display gives the option to revert to FAC SCH.

a. To restore the factory schedule, press up Sor

down Tuntil the display indicates YES.

b. To cancel this option, ensure display indicates

NO.

3. Press Run Schedule.

Test Mode (Occupied/Not Occupied/Schedule Day)

CAUTION

Possible Equipment Damage.

Equipment damage can result if compressor is

cycled too quickly.

The minimum off time for compressors is

bypassed during Test Mode. Equipment damage

can occur if the compressor is cycled too quickly.

Use the Test Mode to check the thermostat configurations

and operation. To start the system test:

1. Press Schedule Day, Occupied and Not Occupied

simultaneously.

2. The display gives the option to TEST.

a. To enter test mode, press up Sor down Tuntil

the display indicates IN TEST.

b. To cancel this option, ensure display indicates

NO TEST.

3. Press Run Schedule.

NOTES:

— To verify whether or not the system test is still

active, repeat the above process.

— The system test times out after ten minutes

with no key pressed.

Save User Schedule (Info/Copy)

Performing this operation saves the current schedule

(including holidays) to memory, overwriting the old saved

schedule:

1. Press both Info and Copy.

2. The display gives the option to revert to SAV SHD.

a. To save the current schedule, press up Sor

down Tuntil the display indicates YES.

b. To cancel this option, ensure display indicates

NO.

3. Press Run Schedule.

Get User Schedule (Info/Run)

Getting the user schedule restores the schedule

(including holidays) from saved memory, overwriting the

schedule currently in use:

1. Press both Run Schedule and Info.

2. The display gives the option to GET SHD.

a. To retrieve the saved schedule, press up Sor

down Tuntil the display indicates YES.

b. To cancel this option, ensure display indicates

NO.

3. Press Run Schedule.

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

62-0195—04 8

TROUBLESHOOTING GUIDE (TABLE 4)

Table 4. Troubleshooting Information.

Symptom Possible Cause Action

Display will not

come on.

Thermostat is not being powered. Check that X terminal is connected to the system transformer.

Check for 24 Vac between X and RH terminals.

If missing 24 Vac:

•Check if circuit breaker is tripped; if so, reset circuit breaker.

•Check if system fuse is blown; if so, replace fuse.

•Check if the HVAC equipment power switch is in the Off

position; if so, set to the On position.

•Check wiring between thermostat and HVAC equipment.

Replace broken wires and tighten loose connections.

If 24 Vac is present, proceed with troubleshooting.

Temperature

display is

incorrect.

Room temperature display has

been recalibrated.

Use PDA configuration software to recalibrate as desired.

Thermostat is configured for °F or

°C display.

Press both Run Schedule and Copy, then reconfigure the

display.

Bad thermostat location. Relocate the thermostat.

Display shows three dashes and a

degree sign (all systems shut

down).

T7350 is set for remote sensing and sensor is missing or circuit

is either open or shorted.

Temperature

settings will not

change.

(Example:

Cannot set

heating higher or

cooling lower.)

Upper or lower temperature limits

were reached.

Check the temperature setpoints:

•Heating limits are 40 to 90°F (7 to 31°C)

•Cooling limits are 45 to 99°F (9 to 37°C)

Occupied setpoint temperature

range stops were configured.

Using a PDA, check setpoint stops. If necessary, reconfigure the

stop(s).

Keypad is locked. When a locked

key is pressed, LOCKED appears

momentarily on the LCD.

•Use PDA (Set, Display) to unlock keypad.

•Press both Run Schedule and Copy, then change keypad

lock level.

Room

temperature is

out of control.

Remote temperature sensing is

not working.

Check all remote sensors.

Heat will not

come on.

No power to the thermostat. Check that X terminal is connected to the system transformer.

Check for 24 Vac between X and RH terminals.

If missing 24 Vac:

•Check if circuit breaker is tripped; if so, reset circuit breaker.

•Check if system fuse is blown; if so, replace fuse.

•Check if the HVAC equipment power switch is in the Off

position; if so, set to the On position.

•Check wiring between thermostat and HVAC equipment.

Replace broken wires and tighten loose connections.

If 24 Vac is present, proceed with troubleshooting.

Thermostat minimum off time is

activated.

•Wait up to five minutes for the system to respond.

•Use PDA to configure heating response.

System selection is set to Off or

Cool.

Set system selection to Heat or Auto.

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

9 62-0195—04

WIRING DIAGRAMS (FIG. 7 - 14)

Fig. 7. Typical hookup of T7350A in two-stage heat and one-stage cool conventional system

with two transformers.

Cooling will not

come on.

No power to the thermostat. Check that X terminal is connected to the system transformer.

Check for 24 Vac between X and RH terminals.

If missing 24 Vac:

•Check if circuit breaker is tripped; if so, reset circuit breaker.

•Check if system fuse is blown; if so, replace fuse.

•Check if the HVAC equipment power switch is in the Off

position; if so, set to the On position.

•Check wiring between thermostat and HVAC equipment.

Replace broken wires and tighten loose connections.

If 24 Vac is present, proceed with troubleshooting.

Thermostat minimum off time is

activated.

•Wait up to five minutes for the system to respond.

•Use PDA to configure cooling response.

System selection is set to Off or

Heat.

Set system selection to Cool or Auto.

System indicator

(flame: heat,

snowflake: cool)

is displayed, but

no warm or cool

air is coming from

the registers.

The call for heat or cool is not yet

given.

Check if any stage indicators (dots next to the system indicator)

are displayed. With no display of stage indicators, no call for

cool/heat is yet given.

For T7350M models only: Check the information screens. A

MODHEAT or MODCOOL percentage of zero indicates a signal

of 4 mA from the given terminal.

Conventional heating equipment

turns the fan on only after the

furnace has warmed to a setpoint.

Wait one minute after seeing the on indicator and then check the

registers.

Heating or cooling equipment is

not operating.

Verify operation of heating or cooling equipment in self-test.

Table 4. Troubleshooting Information. (Continued)

Symptom Possible Cause Action

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

WHEN INSTALLED ON A SYSTEM WITH TWO TRANSFORMERS, REMOVE THE FACTORY-INSTALLED JUMPER.

M19764A

RCX

SUBBASE

W1 GY1AUXRH

(HOT)

L2 1

(HOT)

COMPRESSOR

CONTACTOR 1

HEATING

TRANSFORMER

COOLING

TRANSFORMER

FAN

RELAY

HEAT

RELAY 2

HEAT

RELAY 1

T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT

62-0195—04 10

Fig. 8. Typical hookup of T7350B in two-stage heat and two-stage cool heat pump system

with two transformers.

Fig. 9. Typical hookup of T7350B in three-stage heat and two-stage cool conventional system

with two transformers.

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

WHEN INSTALLED ON A SYSTEM WITH TWO TRANSFORMERS, REMOVE THE FACTORY-INSTALLED JUMPER.

USE ECONOMIZER INSTRUCTIONS FOR INSTALLATION DIRECTIONS.

M19765A

RCX

SUBBASE

W1 G

T7770 REMOTE SENSOR

W2 Y2

AUX

T5 T6 T7 T4 T3

DISCHARGE

AIR

SENSOR

OUTDOOR

AIR

SENSOR

OSOS ASAS

(HOT)

L2 1

(HOT)

COMPRESSOR

CONTACTOR 1

COMPRESSOR

CONTACTOR 2

HEATING

TRANSFORMER

COOLING

TRANSFORMER

HEAT

RELAY 1

123456789

FAN

RELAY

ECONOMIZER

HEAT

RELAY 2

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.

WHEN INSTALLED ON A SYSTEM WITH TWO TRANSFORMERS, REMOVE THE FACTORY-INSTALLED JUMPER.

M22007

RCX

SUBBASE

W1 G

T7770 REMOTE SENSOR

W2 Y2

AUXRH

T5 T6 T7 T4 T3

DISCHARGE

AIR

SENSOR

OUTDOOR

AIR

SENSOR

OSOS AS

(HOT)

L2 1

(HOT)

COMPRESSOR

CONTACTOR 1

COMPRESSOR

CONTACTOR 2

HEATING

TRANSFORMER

COOLING

TRANSFORMER

HEAT

RELAY 1

123456789

FAN

RELAY

HEAT

RELAY 2

HEAT

RELAY 3

Otros manuales para WebStat T7350

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell PRO TH4000 series Manual de usuario

Honeywell

Honeywell FocusPRO 5000 Manual de usuario

Honeywell

Honeywell PRO TH3210D Manual de usuario

Honeywell

Honeywell 191108AJ Manual de usuario

Honeywell

Honeywell Home Pro Series Manual de usuario

Honeywell

Honeywell 9000 Series Manual de usuario

Honeywell

Honeywell THX9000 Prestige HD Guía del usuario

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Manual de usuario

Honeywell

Honeywell RTH111 series Manual de usuario

Honeywell

Honeywell Prestige IAQ YTHX9421 Manual de usuario

Honeywell

Honeywell TH5220D1003 - Digital Thermostat, 2h Manual de usuario

Honeywell

Honeywell Easy-To-See TRADELINE T841B Manual de usuario

Honeywell

Honeywell VisionPRO TH8000 Series Manual de usuario

Honeywell

Honeywell RTH2510 Series Manual de usuario

Honeywell

Honeywell Lyric T5 Wi-Fi Manual de usuario

Honeywell

Honeywell T10 Pro Smart Manual de usuario

Honeywell

Honeywell RTH7400 series Manual de usuario

Honeywell

Honeywell RTH9590 Manual de usuario

Honeywell

Honeywell T8601D Manual de usuario

Honeywell

Honeywell TRADELINE R8184G Guía

Honeywell

Honeywell ultrastat CT1700A Manual de usuario

Honeywell

Honeywell TROL-A-TEMP T874A Manual de usuario

Honeywell

Honeywell VisionPRO IAQ Manual de usuario

Honeywell

Honeywell YRTH7500D1009 - 5 Day Program Thermostat Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario