Honeywell RTH2300B Manual de usuario

RTH2300/RTH221

Programmable Thermostat

Quick Installation Guide

69-2448ES-03

69-2448ES—03 ii

Quick Installation Guide

Identify System Type

This thermostat is compatible with the following systems:

Gas, oil or electric furnace•

Central air conditioner•

Hot water system with or without pump•

Millivolt system•

Central heating and cooling system•

Heat pump without auxiliary/backup heat•

Do you need assistance?

We are here to help.

Call 1-800-468-1502.

This thermostat cannot be used on heat pumps with

auxiliary/backup heat or on multistage systems.

1 69-2448ES—03

RTH2300/RTH221

1Turn Off Power to Heating/

Cooling System

M28097

69-2448ES—03 2

Quick Installation Guide

Remove Old Thermostat

M28099

Old thermostat

Cover

Remove old thermostat but leave wallplate with

wires attached.

Do not remove

wallplate yet

MERCURY NOTICE

Do not put your old thermostat

in the trash if it contains

mercury in a sealed tube.

Contact your local waste

management authority for

instructions regarding recycling

and proper disposal.

3 69-2448ES—03

RTH2300/RTH221

If any wires are not attached to your old thermostat or are

attached to a terminal marked Cor C1, they will not be

connected to your new thermostat. Wrap the bare metal

end of each of these wires with electrical tape, so it can-

not touch and short other wires.

Identify Wires

M29988

Disconnect wires and remove the old wallplate only after

all wires are labeled. Wrap the wires around a pencil to

prevent them from falling though the wall opening.

Do not use non-connected

wires.

Do not use C or C1 wires.

Identify and label each wire.

IGNORE WIRE COLORS:

Use terminal screw

designations to identify

wires.

69-2448ES—03 4

Quick Installation Guide

Mount New Wallplate

Loosen the locking screw at the bottom of the1. thermostat. Note that the screw is captive and cannot

be removed from the wallplate.

Separate the thermostat from the wallplate as per

2. Figure 1.

Position the wallplate against the wall and mark hole

3. positions with a pencil.

NOTE: Levelling is for esthetics only and will not affect

the performance of the thermostat.

Drill holes at the marked positions and insert supplied

4. wall anchors.

Pass the wires through the large opening located at

5. the bottom center of the wallplate as per Figure 2.

Secure the wallplate to the wall with supplied mounting

6. screws as per Figure 3.

Connect the wires to the terminals.

Figure 1 Figure 2 Figure 3

M32154

5 69-2448ES—03

RTH2300/RTH221

Connect Wires (typical wiring)

Loosen the terminal screws using a screwdriver, insert2. the wires, then tighten the screws.

Push any excess wire back into the wall opening.

Labels don’t match?

If a wire does not match any terminal designation, see next page.

Match each labeled wire with the terminal having the1. same letter.

O/B Y RC R G W

M32155

REMOVE JUMPER

IF YOU HAVE BOTH

RAND RC WIRES

69-2448ES—03 6

Quick Installation Guide

Connect Wires (alternate wiring)

If labeled wire does not match any terminal designation, see

diagram below.

M32169A

REMOVE JUMPER BETWEEN RAND RC IF YOU HAVE

WIRES ON BOTH RAND RC.

DO NOT USE C, C1, OR X WIRE. DO NOT USE B WIRE

IF YOU ALREADY HAVE 0 WIRE. WRAP BARE END OF

WIRE WITH ELECTRICAL TAPE.

PLACE A JUMPER (PIECE OF WIRE) BETWEEN Y AND

W IF YOU ARE USING A HEAT PUMP WITHOUT

AUXILIARY/BACKUP HEAT.

O/B Y RC R G W

2 33 1

7 69-2448ES—03

RTH2300/RTH221

Set jumper JP1, on the back of the thermostat, if you

have connected a wire to the G terminal.

Set Heating Fan Control

HG Leave the jumper in this factory-set position if

you have a gas or oil furnace.

HE Place the jumper to this position if you have

an electric furnace.

Incorrect jumper setting: An incorrect setting is notice-

able in a gas or oil heating system. When heating starts,

you will initially feel cold air coming out of the vents as

the fan is running before the furnace has enough time to

heat up the air.

JP1

69-2448ES—03 8

Quick Installation Guide

Set jumper JP2, on the back of the thermostat, if you

have a heat pump.

Set Heat Pump Reversing Valve

O Leave the jumper in this factory-set position if

you have connected O wire to the O/B terminal.

B Place the jumper to this position if you have

connected B wire to the O/B terminal.

Incorrect jumper setting: The heat pump operation will

be reversed, i.e., it will cool in Heat mode and will heat in

Cool mode.

JP2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell RTH2510 Series Manual de usuario

Honeywell

Honeywell 32207484 Manual de usuario

Honeywell

Honeywell CT3200 series Especificaciones técnicas

Honeywell

Honeywell TL8100A1008 - Line Voltage Thermostat Manual de usuario

Honeywell

Honeywell TS822A Manual de usuario

Honeywell

Honeywell PB112C-GA Manual de usuario

Honeywell

Honeywell T6R-HW Manual de usuario

Honeywell

Honeywell RTH7400 series Manual de usuario

Honeywell

Honeywell T1 Pro Manual de usuario

Honeywell

Honeywell FocusPRO TH5110D Manual de usuario

Honeywell

Honeywell t8501A Manual de usuario

Honeywell

Honeywell TH9000 Series Manual de usuario

Honeywell

Honeywell CM737 Manual de usuario

Honeywell

Honeywell CT70A Manual de usuario

Honeywell

Honeywell MagicStat /28 Manual de usuario

Honeywell

Honeywell Prestige THX9321R01 Manual de usuario

Honeywell

Honeywell Braukmann T104F Manual de usuario

Honeywell

Honeywell Super Tradeline T874G Manual de usuario

Honeywell

Honeywell RLV3100 Manual de usuario

Honeywell

Honeywell RTH6300B Manual de usuario

Honeywell

Honeywell T8095A Manual de usuario

Honeywell

Honeywell TRADELINE R8184G Guía

Honeywell

Honeywell Y9420H Sundial RF2 Manual de usuario

Honeywell

Honeywell T7300F Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario