Honeywell Pro Series Manual de usuario

Package Includes:

• T10 Pro Smart Thermostat

• UWP™ Mounting System

• Standard Installation Adapter (J-box

adapter)

• Cover Plate – Medium: Size 511/64" X

51/2” X 11/16" (131.4 mm x 139.7 mm

x 17.5 mm)

• RedLINK Wireless Indoor Air Sensor

(QTY 1)

• Screws and Anchors

• Professional Install Guide

• Getting Started Guide

THX321WF2001W depicted.

Other models may vary.

T10 Pro Smart

Thermostat with

RedLINK™

THX321WFS20 01W

Programmable Thermostat

Professional Install Guide

Read before installing

33-00423EFS-03

Compatibility

• Compatible with most heating, cooling, and heat pump systems

• Required: 24 VAC power (“C” wire)

• Does not work with electric baseboard heat (120240V)

• Does not work with millivolt systems

• Android or iOS smartphone or tablet

Customer assistance

WEB honeywellhome.com

PHONE 18006333991

UWP Mounting System installation

1. Open package to find the UWP. See

Figure 1.

2. Position the UWP on the wall. Level and

mark hole positions. See Figure 2.

Drill holes at marked positions, and

then lightly tap supplied wall anchors

into wall using a hammer.

‒Drill 7/32” holes for drywall.

3. Pull the door open and insert wires

through wiring hole of the UWP. See

Figure 3.

4. Place the UWP over the wall anchors.

Insert and tighten mounting screws

supplied with the UWP. Do not

overtighten. Tighten until the UWP

no longer moves. Close the door. See

Figure 4.

Optional Cover Plate installation

Use the Optional Cover Plate when:

• Mounting the thermostat to an

electrical junction box

• Or when you need to cover paint gap

from the old thermostat.

5. Separate the Junction Box Adapter

from the Cover Plate. See Figure 5.

6. Mount the Junction Box Adapter to

the wall or an electrical box using any

of the eight screw holes. Insert and

tighten mounting screws supplied with

Cover Plate Kit. Do not overtighten.

Make sure the Adapter Plate is level.

See Figure 6.

7. Attach the UWP by hanging it on the

top hook of the Junction Box Adapter

and then snapping the bottom of the

UWP in place. See Figure 7.

8. Snap the Cover Plate onto the

Junction Box Adapter. See Figure 8.

Use 3x supplied

screws #8 11/2”

Use 2x

supplied

screws

#6 5/8”

1/4” to 3/8”

3 4

1 2

M37809

Terminal designations

Conventional Systems Heat pump systems

Terminal Description Terminal Description

S/S Input for a wired indoor,

outdoor sensor S/S Input for a wired indoor,

outdoor sensor

Y Compressor Stage 1 Y Compressor Stage 1

Y2 Compressor Stage 2 Y2 Compressor Stage 2

G Fan Relay G Fan Relay

C24VAC Common wire from

secondary side of cooling

transformer (if 2 transformers) C24VAC Common wire from

secondary side of cooling

transformer

K* Connect to K on C-wire

adaptor K* Connect to K on C-wire

adaptor

U/U** Relay for humidifier,

dehumidifier, or ventilator U/U** Relay for humidifier,

dehumidifier, or ventilator

A L/A Connect to compressor

monitor

W Heat Stage 1 O/B Changeover valve for heat

pumps

W2 Heat Stage 2 Aux Backup Heat

E Emergency Heat

R 24 VAC Heating transformer R 24 VAC Heating transformer

Rc 24 VAC Cooling transformer Rc 24 VAC Cooling transformer

* The THP9045A1098 C-wire adaptor is used on heat/cool systems when you only have four wires at

the thermostat and you need a fifth wire for a common wire. Use the K terminal in place of the Y and

G terminals on conventional or heat pump systems to provide control of the fan and the compressor

through a single wire—the unused wire then becomes your common wire. See THP9045 instructions

for more information.

** See note on Wiring U terminals on the following page.

Wiring UWP

Push down on the tabs to put the wires into the inner holes of their corresponding

terminals on the UWP (one wire per terminal) until they are firmly in place. Gently

tug on the wires to verify they are secure. If you need to release the wires again,

push down the terminal tabs on the sides of the UWP.

This wiring is just an example,

yours may vary.

Setting Slider Tabs

Set R Slider Tab, see Figure 9.

• Use built-in jumper (R Slider Tab)

to differentiate between one or two

transformer systems.

• If there is only one R wire, and it is

connected to the R, Rc, or RH terminal

on the old thermostat, set the slider to

the up position (1 wire).

• If there is one wire connected to the R

terminal and one wire connected to the

Rc terminal, set the slider to the down

position (2 wires).

Set U Slider Tab, see Figure 10.

• Use built-in jumper (U Slider Tab) for

IAQ device.

• When the U Slider Tab is in the down

position (2 wires) the U contacts are a

dry set of contacts.

• If your IAQ device is powered by the

cooling transformer, move the U Slider

Tab to the up position (1 wire). When

this is done, the lower U terminal is

internally jumped to the Rc terminal.

In this application, you would hook

up one wire from your IAQ device to

the upper U terminal and the other

to the common side of the cooling

transformer. The 1 wire setting is most

commonly used when using a fresh

air damper for ventilation or using low

speed fan for dehumidification.

• See wiring examples on the next page.

Whole house humidifier, dehumidifier, or ventilator

Using U Slider Tab

Wired to humidifier,

dehumidifier or ventilator

with built-in transformer.

Wired to fresh air damper

transformer.

11 12

Damper

C from furnace

or air-handler

Humidiﬁer,

dehumidiﬁer,

or ventilator

Wired to humidifier, ventilator,

or damper powered by external

transformer

Wired to low speed fan

terminal on HVAC for

dehumidification

13 14

Humidiﬁer,

dehumidiﬁer,

or ventilator

R from 24 volt

transformer

C (common) from

24 volt transformer

Dehumidiﬁer*

Furnace or

air-handler

* Label for this terminal

varies by equipment

* This thermostat requires a C-Wire. If a C-Wire is not available, use C-Wire adapter accessory

THP9045A1098.

Wiring

1H/1C System (1 transformer)

RPower

Rc [R+Rc joined by Slider Tab]

YCompressor contactor

C* 24VAC common

WHeat relay

GFan relay

NOTES:

1. Use 18 to 22 gauge thermostat wire. Shielded cable is not required.

2. Set the R Slider Tab on the UWP to the up position (1 wire) for 1 transformer

systems or the down position (2 wires) for 2 transformer systems. See "Setting

Slider Tabs" on page 4.

3. Set the U Slider Tab as shown in the diagrams on page 4.

Conventional systems

1H/1C System (2 transformers)

RPower (heating transformer)

Rc Power (cooling transformer)

YCompressor contactor

C* 24 VAC common from cooling transformer

WHeat relay

GFan relay

2H/2C System (1 transformer)

RPower

Rc [R+Rc joined by Slider Tab]

Y Compressor contactor (stage 1)

C* 24VAC common

WHeat relay (stage 1)

GFan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

Hot Water Relay Panel

RPower

Rc [R+Rc joined by Slider Tab]

WHeat Relay

C* 24VAC common

Heat-only System with Fan

RPower

Rc [R+Rc joined by Slider Tab]

C* 24VAC common

WHeat relay

GFan relay

Cool-only System with Fan

RPower

Rc [R+Rc joined by Slider Tab]

YCompressor contactor

C* 24VAC common

GFan relay

NOTE: If the panel does not provide 24 volts AC

at R and C, set the slider to down position and

wire a separate transformer to Rc and C.

Heat pumps systems

1H/1C Heat Pump System

RPower

Rc [R+Rc joined by Slider Tab]

YCompressor contactor

C* 24VAC common

O/B Changeover valve

GFan relay

2H/1C Heat Pump System

RPower

Rc [R+Rc joined by Slider Tab]

YCompressor contactor

C* 24VAC common

O/B Changeover valve

GFan relay

Aux Auxiliary heat**

EEmergency heat relay**

LHeat pump fault input

2H/2C Heat Pump System

RPower

Rc [R+Rc joined by Slider Tab]

YCompressor contactor (stage 1)

C* 24VAC common

O/B Changeover valve

GFan relay

Y2 Compressor contactor (stage 2)

LHeat pump fault input

3H/2C Heat Pump System

RPower

Rc [R+Rc joined by Slider Tab]

YCompressor contactor (stage 1)

C* 24VAC common

O/B Changeover valve

GFan relay

Aux Auxiliary heat**

EEmergency heat relay**

Y2 Compressor contactor (stage 2)

LHeat pump fault input

* This thermostat requires a C-Wire. If a C-Wire is not available, use C-Wire adapter accessory

THP9045A1098.

** If you do not have separate wires for the Aux and E terminals, connect the wire to the Aux terminal.

NOTE: Do NOT use Wfor heat pump applications. Auxiliary heat must wire to AUX or E.

Mounting thermostat

1. Push excess wire back into the wall opening.

2. Close the UWP door. It should remain

closed without bulging.

3. Align the UWP with the thermostat, and

push gently until the thermostat snaps in

place.

Note: If you used the Optional Cover Plate

shown on page 2, remove the gray trim

ring from the thermostat before step 3. Then

align the thermostat with cover plate and push

gently until the thermostat snaps into place.

Note: If needed, gently pull to remove the

thermostat from the UWP

Installer setup

The display will walk you through equipment setup,

connecting to wireless sensors and connecting to

WiFi.

The final step in the setup is a place you can enter

your company name and contact information as

well as your Contractor PRO™ number.

That contact information will be displayed with

alert or reminder messages to keep you connected

to your customer.

Enter your company’s Contractor PRO™ account

number to participate in periodic promotions. Earn

incentives such as bonus points for every T10

Pro Smart thermostat you install during eligible

promotional periods. Your account number is

an 8-digit number that includes a leading zero

(example 01234567).

For questions on this bonus or membership to the

Contractor PRO™ loyalty program, contact us at

18009194835 or contractorpro@resideo.com.

Welcome!

How to use your thermostat

The screen will wake up by pressing the center area of the displayed temperature.

18%

Indoor Temperature

Displays the current

indoor temperature.

Adjust Temperature

Touch the up and

down arrows to

set your desired

temperature.

Current Priority

Displays the type of

priority and number

of rooms being

prioritized.

Contains features

such as mode, fan,

schedule, priority,

and other thermostat

settings.

Indoor Humidity

Displays the current

indoor humidity.

Desired

Temperature

Displays the desired

temperature.

72 72

How to use Priority

Priority creates an average temperature in your home based on speciﬁc rooms. This

allows you to prioritize comfort where you want it.

Selected Rooms

Rooms you manually select create an average

temperature in your home.

Unselected Room

Will not contribute to the average temperature.

Selected Room

Will contribute to the average temperature.

Active Rooms

Rooms with detected motion are automatically selected

to create an average temperature in your home.

Room without Activity

No motion is detected. Will not contribute to the average

temperature.

Room with Activity

Motion is detected. Will contribute to the average

temperature.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Manual de usuario

Honeywell

Honeywell T810D Manual de usuario

Honeywell

Honeywell FocusPro TH5320R Manual de usuario

Honeywell

Honeywell T6360B1036 Instrucciones de funcionamiento

Honeywell

Honeywell T8665A1002 - Digital Thermostat, 3h Manual de usuario

Honeywell

Honeywell CT54 Manual de usuario

Honeywell

Honeywell v Manual de usuario

Honeywell

Honeywell FocusPRO TH5000 Series Manual de usuario

Honeywell

Honeywell VisionPRO IAQ Manual de usuario

Honeywell

Honeywell T87F Manual de usuario

Honeywell

Honeywell PRO 1000 Manual de usuario

Honeywell

Honeywell CM707 Manual de usuario

Honeywell

Honeywell TL8100 Manual de usuario

Honeywell

Honeywell T8611G Chmnothern IV Manual de usuario

Honeywell

Honeywell Z-Wave Series Manual de usuario

Honeywell

Honeywell CM900 Manual de usuario

Honeywell

Honeywell RTH111 series Manual de usuario

Honeywell

Honeywell Chronotherm CM31 Manual de usuario

Honeywell

Honeywell RTH6300 Manual de usuario

Honeywell

Honeywell Lyric T5 Wi-Fi Manual de usuario

Honeywell

Honeywell T7080A Manual de usuario

Honeywell

Honeywell CT50 Manual de usuario

Honeywell

Honeywell Programmable Thermostat Manual de usuario

Honeywell

Honeywell T7512B Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario

Honeywell pro Series Manual de usuario

Manuales populares de Termostato de otras marcas