Honeywell 10260A Series Manual de usuario

Tabla de contenidos

Otros manuales de Cambiar de Honeywell

Honeywell

Honeywell CLMSOPS5M Manual de usuario

Honeywell

Honeywell C6097 Manual de usuario

Honeywell

Honeywell PK 80148 Manual de usuario

Honeywell

Honeywell Krom Schroder DG H Series Manual de usuario

Honeywell

Honeywell Krom Schroder DL A Series Manual de usuario

Honeywell

Honeywell kromshroeder DL H Series Manual de usuario

Honeywell

Honeywell Galaxy 2 Series Manual de usuario

Honeywell

Honeywell OP-AR Manual de usuario

Honeywell

Honeywell PLS531A Manual de usuario

Honeywell

Honeywell ZW4009 Manual de usuario

Honeywell

Honeywell ZW4003 Manual de usuario

Honeywell

Honeywell ZW4003 Manual de usuario

Honeywell

Honeywell DCM/SN DIFF Manual de usuario

Honeywell

Honeywell 39346 Manual de usuario

Honeywell

Honeywell C645A-E Manual de operación

Honeywell

Honeywell GLS Series Manual de usuario

Honeywell

Honeywell DDS76-1/2 Manual de usuario

Honeywell

Honeywell Q640 Manual de usuario

Honeywell

Honeywell 10260 Series Manual de usuario

Honeywell

Honeywell 50054911 Manual de usuario

Honeywell

Honeywell IP-AK2 Manual del operador

Honeywell

Honeywell ZW4008 Manual de usuario

Honeywell

Honeywell krom schroder DL K Series Manual de usuario

Honeywell

Honeywell 5869 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario

5/99 62-86-33-10 – Kit 1

10260A series Auto/Manual Switch kit

Replacement/Upgrade Instructions

51309623-502

Document Number

Form: 62-86-33-10

Effective: 5-27-99

Supersedes: None

Summary

This kit contains a new auto/manual switch assembly for your 10260A actuator.

Procedure

See Table 1 for procedure.

WARNING

Disconnect power before accessing components inside the instrument.

ATTENTION

When working with circuit cards always protect against electrostatic discharge by wearing a grounded wrist

strap.

62-86-33-10 – Kit 5/992

Table 1 10260A Auto/Manual Switch Installation Procedure

Step Action

1Remove lower rear cover.

2Remove terminal board plate.

3If replacing the switch, disconnect switch wires and remove switch:

•Disconnect auto/manual switch wires from TB1-1, TB1-8, TB1-9, TB2-12, TB2-13, TB4-28, TB4-

29. (TB1 is the top terminal board. TB1-1 is the leftmost terminal on the top terminal board.)

•Remove switch knob by pulling it off the shaft.

•Remove nut securing switch to side of unit.

•Pull switch out of unit side wall.

4Install new switch:

•See Figure 1. Attach switch label to side wall.

•Remove nut from threads on switch. Insert switch through side wall. Make sure the stub

engages the small hole.

•Screw the nut onto the switch shaft and tighten it securely.

•Attach knob to shaft with set screw on flat side of shaft.

Label Auto/Manual Switch

Knob

Figure 1 Auto/Manual Switch Installation

5Connect switch wires:

•If adding (not replacing) the switch, remove blue and orange wires from TB1-8 and 9. Connect

blue wire to TB2-13 and orange wire to TB2-12.

•If adding or replacing the switch, one at a time connect auto/manual switch wires as follows.

Some terminals have dual (piggyback) wires attached; make sure the wires are attached to the

correct terminals. Make sure piggyback wires on outermost terminals are facing the inner

terminals, not facing away from the terminals. For example, TB1-1 should have its piggyback

terminal positioned between TB1-1 and TB1-2.

Black TB1-1, white TB1-8, brown TB1-9, green TB2-12, violet TB2-13, orange TB4-28, red TB4-29.

6Reattach terminal board plate.

7Install new gasket and reattach cover.

5/99 62-86-33-10 – Kit 3

Table 1 10260A Auto/Manual Switch Installation Procedure

Step Action

8Check switch for proper operation:

•Reconnect power.

•Set switch to CW and check for clockwise motion.

•Set switch to CCW and check for counterclockwise motion.

•Set switch to A/M and check for motion per 4-20 mA.

•If motion is incorrect, disassemble and check wiring in step 5. Repeat steps 6-8.