Honeywell 5869 Manual de usuario

The 5869 Hold-Up Switch/Transmitter is a finger-operated

RF transmitting device. It is typically mounted under a

counter or money draw for inconspicuous operation.

When the transmitter is activated, it emits an RF signal to

the receiver. The security system control panel sends a

burglary alarm to the central station when a RF signal is

received from an enrolled Hold-Up Switch/Transmitter.

Once activated, the 5869 Hold-Up Switch/Transmitter can

only be reset by the reset key. The 5869 also incorporates

tamper switches that are activated when the cover is

removed, or if the unit is forcibly removed from its

installation location.

• No wires to run

• Front and back tamper resistant

• Easily mounted

• Quick enrollment

• Includes battery

FEATURES

5869

HOLD-UP SWITCH/TRANSMITTER

Physical

• 1-15/16" W x 5-15/16" H x 1 3/16"D

(50mm x 150mm x 30mm)

Frequency

• 345 MHz

Battery

• 3V Lithium ADEMCO 466

or equivalent

Agency Listings

• UL listed for Household Burg UL

1023,Hold-up Burg UL 636 and

CUL 634

• For certified UL commercial

installations, use with 5881ENHC

tamper-protected wireless receiver

Compatibility

• Fully compatible with all

VISTA Control Panels

SPECIFICATIONS

HOLDUP

TRANSMITTER

DEVICE

MOUNTING

HOLE

COVER

SCREW

MOUNTING

HOLE

COVER

ATTACH

HOLE

TRIGGER

INSIDE VIEW

WITH

CIRCUIT BOARD

RESET

KEY

COVER TAMPER

RELEASE SWITCH

LITHIUM

BATTERY

MOUNTING

HOLE

MOUNTING

HOLE

5869-001-V0

COVER

SCREW

COVER

ATTACH

HOLE

BREAKAWAY

TAMPER

RELEASE TAB

SCREW

HOLE

Figure 1

ORDERING

5869 Hold-Up Switch/Transmitter

5869

HOLD-UP SWITCH/TRANSMITTER

Mount the 5869 under a counter or

money drawer for easy access by the

cashier. Refer to the steps and figures

that follow for typical mounting

instructions. Before mounting the 5869

permanently, perform Go/No Go tests

to verify adequate transmitter signal

strength at desired mounting location

(refer to the Security System Control

Panel Installation and Setup Guide).

1. Remove the two screws (Figure 1)

securing the cover to the 5869 case.

NOTE: The holes located in the opposite corner

to the screws that secure the cover to the case,

provide a means for securing the transmitter to

the counter or drawer.

2. Using the case as a drill

template, position the case

in the desired location.

3. Drill a 1/16"pilot hole at the

breakaway tamper release

hole and the two case mounting

holes (Figure 2).

4. Attach the case to the counter or

money drawer using one No. 6 x 3/4

screw (supplied) at the breakaway

tamper release.

5. Install the battery (see BATTERY

INSTALLATION/REPLACEMENT).

6. Secure the cover to the case with

the two screws removed in step 1.

7. Secure the assembled case to

the counter or drawer using the

two No. 6 x 2 mounting screws

supplied (Figure 2).

INSTALLATION

The 5869 Hold-Up Switch/Transmitter

should be programmed as a 24-hour

silent zone type. Refer to the Security

System Control Panel Installation and

Setup Guide for programming

instructions.

• During programming of the control

panel, the 5869 Hold-Up

Switch/Transmitter should be treated

as “RF” (i.e., supervised RF) Type

• The 5869 is one closed input loop

zone (loop 1)

Battery Installation/Replacement

1. Remove and retain screws securing

the 5869 cover.

2. Observing correct polarity, insert the

battery into the battery holder.

NOTE: Use care not to bend the antenna while

attempting to install battery.

3. Re-install screws to secure cover

and/or assembly. Refer to Figure 1.

PROGRAMMING

5869-002-V0

MOUNTING

HOLE

TRIGGER

HOLE

TRIGGER

BREAKAWAY

TAMPER

RELEASE

RESET

KEY

COVER

TAMPER

RELEASE

SWITCH

MOUNTING

HOLE

COVER

SCREW (2)

No. 6X1/2

COVER

LITHIUM

BATTERY

CIRCUIT

BOARD

COVER

ATTACH HOLE

COVER

ATTACH

HOLE

MOUNTING

SCREW (2)

No. 6X2

BREAKAWAY

TAMPER

RELEASE

SCREW HOLE

INDEX

TAB

COVER

SCREW

NOTE

CIRCUIT BOARD REMOVED

FOR CLARITY ONLY. DO NOT

REMOVE CIRCUIT BOARD

DURING INSTALLATION.

Figure 2

Otros manuales de Cambiar de Honeywell

Honeywell

Honeywell ZW4003 Manual de usuario

Honeywell

Honeywell ZW4008 Manual de usuario

Honeywell

Honeywell 10260 Series Manual de usuario

Honeywell

Honeywell 88173 Manual de usuario

Honeywell

Honeywell Fema DWAM Series Manual de usuario

Honeywell

Honeywell C6045D Manual de usuario

Honeywell

Honeywell RXSW100A3CULH Manual de usuario

Honeywell

Honeywell MICRO SWITCH GSX Manual de usuario

Honeywell

Honeywell C437D Manual de usuario

Honeywell

Honeywell 39351 Manual de usuario

Honeywell

Honeywell PLS730B Manual de usuario

Honeywell

Honeywell 968XTP Manual de usuario

Honeywell

Honeywell S688A Manual de usuario

Honeywell

Honeywell CX Series Guía rápida

Honeywell

Honeywell PEHA PHC Guía del usuario

Honeywell

Honeywell 272630D Manual de usuario

Honeywell

Honeywell PK 88231 Manual de usuario

Honeywell

Honeywell CLMSOPS5M Manual de usuario

Honeywell

Honeywell CS Series Manual de usuario

Honeywell

Honeywell RPLS740B Manual de usuario

Honeywell

Honeywell PK 80148 Manual de usuario

Honeywell

Honeywell Krom Schroder DL A Series Manual de usuario

Honeywell

Honeywell ZW4103 Manual de usuario

Honeywell

Honeywell 50054911 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario