Honeywell Limitless WGLA Series Manual de usuario

Quick Start Guide for the

Limitless™ Series WGLA Limit Switch

used in conjunction with the Limitless™

WPMM Series

ISSUE 1

50053338

Sensing and Control

WARNING

PERSONAL INJURY

DO NOT USE these products as safety or emergency

stop devices or in any other application where failure of

the product could result in personal injury.

Failure to comply with these instructions could result in

death or serious injury.

WARNING

Honeywell does not recommend using devices for critical

control applications where there is, or may be, a single point

of failure or where single points of failure may result in an

unsafe condition. It is up to the end-user to weigh the risks

and benefits to determine if the products are appropriate for

the application based on security, safety and performance.

Additionally, it is up to the end-user to ensure that the control

strategy results in a safe operating condition if any crucial

segment of the control solution fails.

Honeywell customers assume full responsibility for learning

and meeting the required Declaration of Conformity,

Regulations, Guidelines, etc. for each country in their

distribution market.

Failure to comply with these instructions could result in

death or serious injury.

WARNING

RF EXPOSURE

To satisfy FCC RF exposure requirements for mobile

transmitting devices, a separation distance of 20 cm or

more should be maintained between the antenna of this

device and persons during device operation To ensure

compliance, operation at closer than this distance is not

recommended. The antenna used for this transmission

must not be co-located in conjunction with any other

antenna or transmitter.

Failure to comply with these instructions could result

in death or serious injury.

WARNING

The WGLA must be installed in accordance with the

requirements specified in this document. See Section 3

and Section 4 for EIRP requirements. Only the

specified EIRP power settings, antenna types and

gains and cable lengths (attenuation) as outlined in this

document are valid for WGLA Series installations.

CAUTION

Power to the WGLA should not be applied (ensure

battery is removed) during installation of antenna as

damage could occur to the WGLA electronics.

Limitless™WGLA Series Issue 1 50053338

Honeywell Sensing and Control

This WGLA Series quick start installation guide provides basic installation instructions for the WGLA switch used in

conjunction with a Limitless™ Wireless Panel Mount Monitor (WPMM). If necessary, refer to the WGLA or WPMM

Installation and Technical Manual for further detailed information regarding installation.

1.1 Antenna Connection

WARNING

RF EXPOSURE

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm

[7.87 in] or more should be maintained between the antenna of this device and persons during device

operation To ensure compliance, operation at closer than this distance is not recommended. The antenna

used for this transmission must not be co-located in conjunction with any other antenna or transmitter.

Failure to comply with these instructions could result in death or serious injury.

CAUTION

Power to the WGLA should not be applied (ensure battery is removed) during installation of antenna as

damage could occur to the WGLA electronics.

The antenna and antenna guard are packaged separately and thus will need to be assembled to the WGLA.

A direct mount antenna (either straight or tilt & swivel) can be easily mounted by threading the mating RP-SMA

plug of the antenna to the RP-SMA jack on the WGLA. Tighten the connection until finger tight. Then attach the

antenna guard by simply threading the guard finger tight onto the threaded base with the RP-SMA connector.

A remote mount antenna requires the use of an extension cable to allow the antenna to be mounted in a different

location than the WGLA location. The extension cable will need to have one end with a RP-SMA plug connector

which will mate with the WGLA connector jack under the same mounting procedure as the direct mount antenna.

The other end of the extension cable will need to mate with antenna connector directly.

1.2 Battery Connection Procedure

WARNING

RISK OF DEATH OR SERIOUS INJURY FROM EXPLOSION OR FIRE

Connection and disconnection of the batteries should only be performed in a non-hazardous area. The

batteries used in this device may present a risk of fire or chemical burn if mistreated. Do not recharge,

disassemble, heat above 100 °C [212 °F], or incinerate.

Failure to comply with these instructions could result in death or serious injury.

WARNING

RISK OF DEATH OR SERIOUS INJURY FROM EXPLOSION OR FIRE

If WGLA is to be returned to Honeywell for any reason, the battery MUST be removed prior to shipping.

Dispose of used batteries promptly per local regulations or the battery manufacturer’s recommendations.

Keep away from children. Do not disassemble and do not dispose of in fire.

Failure to comply with these instructions could result in death or serious injury.

ATTENTION

Use only the following 3.6V lithium thionyl chloride (Li-SOCl2) battery (non-rechargeable), size 2/3AA.

No other batteries are approved for use in the WGLA Series limit switch.

Uniwell, DEV-10-0009

Honeywell, WBT1

Limitless™WGLA Series Issue 1 50053338

Honeywell Sensing and Control 3

WGLA battery activation:

Tools required: Slotted or Phillips screwdriver

Step Action

1 If applicable, remove the two screws con the housing cover.

2 Using a finger, press down slightly on the battery top dand remove the battery insulator e. Insure that the

battery is properly seated and making good contact.

3 Replace cover and retighten screws or immediately proceed to Section 1.3 Pairing Mode.

Figure 1. Limitless™ Switch Housing Figure 2. Limitless™ Battery and Insulator

1.3 Pairing Mode

Pairing is required to initiate and establish an RF communication link between each single WGLA and a single

WPMM. The WGLA will be shipped from the factory with two identification labels (1) that are recommended to be

completed and applied to the WGLA housing during the pairing mode. As there are up to 16 WGLAs that can be

paired to a single WPMM, these labels will be used to identify the WGLA switch in the sequence of #1 to #16. The

initial WGLA switch paired to the WPMM will be Sequence #1; the second WGLA paired will be Sequence #2 and

so on. If replacing a WGLA switch that has been purged (see section 6.5 of the WPMM Installation and Technical

Manual), identify the correct replacement Sequence # on the identification labels.

ATTENTION

The operation and LED functions for the WPMM are visually depicted and described in Section 5.4 of

the WGLA Installation and Technical manual. This file is also located as a separate file on this CD or

at www.honeywell.com/sensing.

ATTENTION

The operation and LED functions for the WPMM are visually depicted and described in Section 5.4 of

the WGLA Installation and Technical manual. This file is also located as a separate file on this CD or

at www.honeywell.com/sensing.

Limitless™WGLA Series Issue 1 50053338

Honeywell Sensing and Control

The battery will need to be activated in the WGLA and proper power applied to the WPMM (green dLED

illuminated) before proceeding with this pairing procedure. Once the pairing is completed, the WGLA selected will

only communicate with the WPMM it was paired to and no other device.

Step Action

1 Completely read this procedure before starting in order to understand the timing of events that need to be

performed.

2 WGLA: Remove (if required) the two screws hon the housing cover (See Figure 3) of the WGLA and

locate the function button ito be used in Step 4.

3 WPMM: Press the Function button fon WPMM (See Figure 4) for more than four seconds and less than

eight seconds at which time the green dand amber eLEDs will be flashing which indicates to release the

function button immediately as it has entered the pairing mode.

4 WGLA: Within a 30 second interval of Step 3, depress the WGLA switch function button i(See Figure 5)

and hold depressed for more than one second and less than 12 seconds at which time the orange jLED

turns on. While in pairing mode, the orange led will flash on for 100 ms every second. The orange jLED

flashes three times 100 ms on, 100 ms off when pairing succeeds. If pairing does not succeed, the orange

jLED will turn off and user will need to repeat steps starting with Step 3.

5 WPMM: Successful pairing will be indicated by the green dand amber eLEDs (See Figure 4) ceasing to

flash and remaining on for a few seconds before turning off. A short buzzer beep will also occur.

6 To confirm proper pairing between the WGLA and WPMM, actuate the WGLA, and the red LED gshould

illuminate along with a buzzer sound.

7 Record the WGLA Sequence # on identification labels cand apply to the WGLA housing in desired

locations (See Figure 6).

8 Repeat Steps 2-7 to add additional WGLA switches. Up to 16 WGLAs can be paired to a single WPMM.

Limitless™WGLA Series Issue 1 50053338

Honeywell Sensing and Control 5

Figure 3. Limitless™ Switch Housing Figure 5. Limitless™ Switch with Function Button

Depressed

Figure 4. Limitless™ Switch Housing

NOTE: Use a blunt object, such as a paper clip or

tooth pick to actuate the function switch i.

NOTE: Use a blunt object, such as a paper clip or

tooth pick to actuate the function switch f.

Figure 6. Limitless™ Switch Label Placement

Limitless™WGLA Series Issue 1 50053338

Honeywell Sensing and Control

1.4 WGLA Mounting

The WGLA housing has four mounting holes that will accept a M5 or #10 size screw. Two of the mounting holes

are slotted to allow adjustment of the switch actuator to the customer actuator during installation. It is suggested

that the two slotted holes have screws installed and adjustment be made before installing screws in the non-slotted

holes.

Note: The adjustment process should not allow preload of the switch actuator and the full travel of the switch

actuator should not exceed the switch over travel maximum specification. (See installation drawing at

www.honeywell.com/sensing)

Figure 7. Limitless™ WGLA mounting hole diagram

The WGLA Series switch has many actuator types and associated specifications.

Additional information can be found at: www.honeywell.com/sensing

Limitless™WGLA Series Issue 1 50053338

Honeywell Sensing and Control 7

1.5 Antenna Adjustment

The antenna of the WGLA and WPMM should be oriented with respect to each other such that they are parallel.

This will in most cases allow the longest range and highest RF communication link/signal. The least RF signal is

normally in a direction in-line with the top of the antenna, so it is best to avoid having the antennas pointed directly

toward each other, or directly away from each other. An acceptable RF signal is also indicated by the WPMM. This

can be checked by making sure the red gLED turns on when the WGLA is actuated but the amber eLED is off.

Figure 8. Limitless™ WGLA and WPMM in parallel Figure 9. Limitless™ WPMM LED display

NOTE: Use a blunt object, such as a paper clip or tooth

pick to actuate the function switch f.

WARNING

RF EXPOSURE

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20 cm

[7.87 in] or more should be maintained between the antenna of this device and persons during device

operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna

used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.

Failure to comply with these instructions could result in death or serious injury.

Limitless™WGLA Series Issue 1 50053338

Sensing and Control

Honeywell

1985 Douglas Drive North

Golden Valley, MN 55422

www.honeywell.com

50053338-1-EN IL50 GLO Printed in USA

May 2010

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as being free

of defective materials and faulty workmanship. Honeywell’s

standard product warranty applies unless agreed to

otherwise by Honeywell in writing; please refer to your

order acknowledgement or consult your local sales office

for specific warranty details. If warranted goods are

returned to Honeywell during the period of coverage,

Honeywell will repair or replace, at its option, without

charge those items it finds defective. The foregoing is

buyer’s sole remedy and is in lieu of all other

warranties, expressed or implied, including those of

merchantability and fitness for a particular purpose. In

no event shall Honeywell be liable for consequential,

special, or indirect damages.

While we provide application assistance personally, through

our literature and the Honeywell web site, it is up to the

customer to determine the suitability of the product in the

application.

Specifications may change without notice. The information

we supply is believed to be accurate and reliable as of this

printing. However, we assume no responsibility for its use.

SALES AND SERVICE

Honeywell serves its customers through a worldwide

network of sales offices, representatives and distributors.

For application assistance, current specifications, pricing or

name of the nearest Authorized Distributor, contact your

local sales office or:

E-mail: [email protected]

Internet: www.honeywell.com/sensing

Phone and Fax:

Asia Pacific +65 6355-2828

+65 6445-3033 Fax

Europe +44 (0) 1698 481481

+44 (0) 1698 481676 Fax

Latin America +1-305-805-8188

+1-305-883-8257 Fax

USA/Canada +1-800-537-6945

+1-815-235-6847

+1-815-235-6545 Fax

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Honeywell:

WGLA1A01BA1A WGLA1A02BA1A WGLA1A02BA1B WGLA1A02BA4J WGLA1A04BA1A WGLA1A04BA1B

WGLA1A04BA4J WGLA1A04BB WGLA1A04BC WGLA1A02AA1A WGLA1A02AA1B WGLA1A02AA4J

WGLA1A04AA1A WGLA1A04AA1B WGLA1A04AA4J WGLA1A02BB WGLA1A02BC WGLA1A02BD

Otros manuales para Limitless WGLA Series

Tabla de contenidos

Otros manuales de Cambiar de Honeywell

Honeywell

Honeywell Switches and Sensors Manual de usuario

Honeywell

Honeywell RTS-CSA Manual de usuario

Honeywell

Honeywell MICRO SWITCH GSX Manual de usuario

Honeywell

Honeywell Micro Switch 91SE Series Manual de usuario

Honeywell

Honeywell RXSW100A3CULH Manual de usuario

Honeywell

Honeywell RXSM100A3 Manual de usuario

Honeywell

Honeywell KSL Series Manual de operación

Honeywell

Honeywell 272630D Manual de usuario

Honeywell

Honeywell CSP-C Manual de usuario

Honeywell

Honeywell C6097B Manual de usuario

Honeywell

Honeywell IDENT-KEY 3 Manual de usuario

Honeywell

Honeywell GSS Series Manual de usuario

Honeywell

Honeywell Ademco VistaView-100 Instrucciones de montaje

Honeywell

Honeywell PLS530A Manual de usuario

Honeywell

Honeywell CENTRAL HUB Manual de usuario

Honeywell

Honeywell krom schroder DL K Series Manual de usuario

Honeywell

Honeywell ZW4003 Manual de usuario

Honeywell

Honeywell Q682B Guía del usuario

Honeywell

Honeywell PEHA PHC Guía del usuario

Honeywell

Honeywell miniMAX Manual de usuario

Honeywell

Honeywell 39351 Manual de usuario

Honeywell

Honeywell 10260A Series Manual de usuario

Honeywell

Honeywell 5869 Manual de usuario

Honeywell

Honeywell OP-AR Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario