Honeywell SILENT KNIGHT RA-2000 Manual de usuario

RA-2000 Remote Annunciator

Installation

The optional Model RA-2000 red remote annunciator, shown in

Figure 1, performs the same functions as the on-board

annunciator. Operation is identical. The RA-2000 can be surface

or flush mounted and is available in gray color as

RA-2000GRAY.

Figure 1: Model RA-2000 Remote Annunciator

RA-2000 installation involves the following steps:

1. Make sure power is off at the panel.

2. Mount the RA-2000 in the desired location (see Section

“Mounting the RA-2000” ).

3. Connect the RA-2000 to the panel (see Figure 2).

4. Use the dipswitches on the back of the RA-2000 to assign

an ID# to the RA-2000 (see Section 4.10.1 of Manual P/N

151430).

5. The RA-2000 module must be added to the system through

programming. JumpStart Auto Programming will add the

module automatically (refer to Manual P/N 151430).

Wiring Connections

Wire the RA-2000 to the FACP as Shown in Figure 2.

Figure 2: SBUS Connections

Specifications

Mounting the RA-2000

This section of the manual describes mounting the remote

annunciator. The annunciator can be flush- or surface-mounted.

Flush Mounting

This section of the manual describes flush mounting.

Follow these steps to flush mount the RA-2000

1. The back box dimensions are 9-3/8” w x 8-3/8” h. The

minimum depth 2". The back box can be mounted prior to

the complete installation of the RA-2000 using any of the

mounting holes shown in Figure 3.

Figure 3: Back Box Mounting Holes

2. Remove knockout holes as needed for wires. See Figure 4

Parameter Value

Operating Voltage: 24 VDC

Current Standby: 25 mA

Alarm: 50 mA

Operating Temperature: 0° to 49° C (32° to 120° F)

Dimensions:

Flush

Mount: Overall: 12-1/4” W x 11.5” H x 7/8” D

31.1 cm W x 29.2 cm H x 2.2 cm D

See “Flush Mounting” for back box

dimensions.

Surface

Mount: Including trim ring:

12-1/4” W x 11.5” H x 3” D

31.1 cm W x 29.2 cm H x 7.6 cm D

Mounting Holes

Model RA-2000 Installation Instructions

2P/N 151443 Rev B

for backbox knockout locations

Figure 4: Back Box Knockout Locations

3. Wire the Annunciator board to the main control panel. See

Figure 2.

4. Attach the annunciator and door assembly to back box as

shown in Figure 5 using the supplied screws.

Figure 5: Attaching Annunciator/Door Assembly to

Backbox

Surface Mounting

The Model RA-2000TR red trim ring and RA-2000GRAYTR

gray trim ring kits are available for use when surface mounting.

1. Remove the desired knock out. See Figure 4.

2. To properly mount the back box, insert a single screw into

the key shaped mounting hole. Do not tighten all the way.

See Figure 6.

Place a level on top of the back box, with the back

box level insert the rest of the mounting screws.

Figure 6: Back Box Surface Mount Holes

3. Run wires to the control panel.

4. Place the trim ring over the back box as shown in Figure 7.

Figure 7: Installing Trim Ring

5. Attach the Door assembly to the back box using screws

provided.

6. After the annunciator wiring to the panel has been

completed, replace the electronic assembly in the back box.

Place the bezel over the back box and tighten the set screws

on the bezel.

Wire Knockouts

Key Shaped

Mounting Hole

Back Box

Mounting Holes

Otros manuales de Sistema de seguridad de Honeywell

Honeywell

Honeywell Domonial Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Manual de usuario

Honeywell

Honeywell INTELLIGUARD 9000 Manual

Honeywell

Honeywell First Alert FA130CP Manual de usuario

Honeywell

Honeywell Le Sucre Manual de usuario

Honeywell

Honeywell NETAXS NX4L1 Manual de usuario

Honeywell

Honeywell Galaxy Keyprox Especificaciones técnicas

Honeywell

Honeywell X-618 Manual de usuario

Honeywell

Honeywell ESSER Manual de usuario

Honeywell

Honeywell VISTA-15P Manual de usuario

Honeywell

Honeywell VISTA 15P - Ademco 6 Zone Control Panel Manual de usuario

Honeywell

Honeywell sixsiren Manual de usuario

Honeywell

Honeywell SEF8MS Manual de usuario

Honeywell

Honeywell VISTA-21iP Instrucciones de montaje

Honeywell

Honeywell ADEMCO VISTA-20PSIA Manual de usuario

Honeywell

Honeywell LYNX Touch L7000 Series Manual de usuario

Honeywell

Honeywell ADEMCO LYNXR-I Security System Manual de usuario

Honeywell

Honeywell VISTA-128BPTSIA Manual de usuario

Honeywell

Honeywell Evohome Manual de usuario

Honeywell

Honeywell NOTIFIER DSE3-23 Series Manual de usuario

Honeywell

Honeywell Water Defense RWD41 Manual de usuario

Honeywell

Honeywell Home SI800MS Manual de usuario

Honeywell

Honeywell Ademco VISTA-50P Instrucciones de funcionamiento

Honeywell

Honeywell Ademco VISTA-32FB Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario