Honeywell GKP-S8M Guía de configuración

GKP-S8M

Wireless Keypad with Integrated Tag Reader and Siren

Compliant with:

EN50131-3 Grade 2 Class II for keypad

EN50131-4 Grade 2 Class II for siren

Applicable CE compliance Declaration of Conformity available at:

www.honeywell.com/security/uk/hscdownload

800-20981-A

Honeywell Security Group –Sécurité Communications SAS

1198 Av. du Docteur Maurice Donat –BP1219 –06254 Mougins Cedex Sophia-Antipolis –France

Tél: +33 (0) 492 942 950 –Fax : +33 (0) 492 942 960 www.honeywell.com/security/fr

SECURITE COMMUNICATIONS: S.A.S. au capital de 4 123 680 €

RCS CANNES B310 245 931 –SIRET 310 245 931 00079 –APE 322 B –N°TVA: FR 10 310245931

⑨

⑤

⑦

①

②

④

③

⑧

⑥

⑨

⑩

4mm x 3.5mm

⑪

⑫

2x CR123A

⑬

⑭

⑮

⑭

INSTALLATION INSTRUCTIONS

The keypad is designed to control the DOMONIAL panel series. It features a proximity tag

reader and an integrated siren for deterrent action and is used to arm and disarm your

security system.

FEATURES

Total Setting (①) / Part Setting (②) / Annex Setting (key “7” + key “9”)

Unsetting via code or Tag (③)

Panic Alert (SOS): push ④+⑤simultaneously

4 Status LEDs to indicate system status/faults (⑥)

“Ghost Light” LEDs to light the keypad during operation

Siren (⑦)

Tag Reader (⑧)

MOUNTING

The keypad must be installed on its mounting bracket and is not meant to be used outside

its bracket. This bracket must be fixed on a wall and easily accessible for the arming and

disarming of the system.

Mounting steps:

1) Separate the bracket (⑨) from the keypad (⑩)

2) Fix the bracket on the wall using 3 screws (⑪)

3) Remove the plastic strips to power the keypad (⑫)

4) Put the keypad back in its bracket (⑬)

5) Secure the keypad in its bracket with the supplied screw (⑭)

REGISTRATION

The registering is the procedure associating the keypad to the panel. This operation

requires a programming tool. The complete procedure is described in the alarm central

unit installation notice or in the programming tool manual.

Up to 4 keypads of this type can be used per installation.

1) Connect the programming tool and start programming.

2) Go to the « Register » menu and put the panel into registration mode.

3) To register the keypad remove the keypad from its mounting bracket and insert it again

to generate a radio pulse (tamper) or trigger an alert by pressing simultaneously (④)

and (⑤) keys.

The keypad will beep during the time between tamper/alert activation and the confirmation

by the panel.

4) Configure the keypad in the programming tool:

- Set label of the device

- Choose alert mode (1: silent, 2: beep or 3: siren)

- Choose associated set (Total only, Annex only, Total + Annex)

5) Exit programming mode.

BATTERY REPLACEMENT

The keypad signals a battery failure at the control panel when the battery needs to be

replaced. The system fault LED lights on to signal locally the battery fault to the user

(please refer to the User guide to know the different Status LEDs meanings). The keypad

will continue to operate for up to one month after this. Replace the batteries with CR123A

3V Lithium batteries only.

To replace the batteries follow the procedure described below:

1. Unscrew the securing screw (⑭) and remove the keypad from its mounting bracket.

2. A tamper alarm is sent to the panel and there is a 120-second delay before

transmitting the specific tamper message to the monitoring station. If tamper is

restored before the end of the delay there is no transmission. (The tamper delay is

active only when the keypad set is disarmed. Tamper is immediately transmitted if the

keypad set is armed).

3. Remove the batteries and replace them with new batteries from the same type

(CR123A) respecting the polarities (⑮).

4. Put the keypad back in its bracket (⑬).

5. Secure the keypad in its bracket with the supplied screw (⑭).

PROGRAMMING THE KEYPAD (Installer Mode)

The keypad features 2 programming modes which allow the installer and end user to

control the keypad functionalities.

The procedure bellow explains the procedure to enter the installer programming mode.

For details on the end user’s programming mode please refer to the user’s manual.

To enter installer’s programming mode:

1) Press simultaneously the two buttons “1” and “3” more than 2 seconds and release

them.

➔A double beep is played and all Status LEDs light up.

2) Enter installer’s code

➔All Status LEDs start flashing and a long beep is played

To exit installer’s programming mode and save your changes:

3) Press (⑤) to exit programming and save your changes

➔All LEDs stop flashing and a double beep is played.

Note: The system will automatically exit programming mode after 20 seconds if no keys

are pressed during this period. If this occurs, you must repeat all the steps necessary for

the function you are using.

In programming mode, it is possible to:

Set arming with identification:

1. Press “Total arming” button to select function

2. Press (④) to activate arming with identification (code and TAG)

Set quick arming:

1. Press “Total arming” button to select function

2. Press (⑤) to activate quick arming

Associate a TAG to a user: