Honeywell Lyric SIXSIREN Manual de usuario

Tabla de contenidos

Otros manuales de Sistema de seguridad de Honeywell

Honeywell

Honeywell Esser 804950 Manual de usuario

Honeywell

Honeywell Fire-Lite Alarms MS-9200UDLSC Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Instrucciones de funcionamiento

Honeywell

Honeywell RCWL200A Manual de usuario

Honeywell

Honeywell LYNX Touch Series Instrucciones de montaje

Honeywell

Honeywell First Alert FA168CPS Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-12A Manual de usuario

Honeywell

Honeywell nfs2-3030 Manual de usuario

Honeywell

Honeywell INTELLIGUARD 9000 Manual de usuario

Honeywell

Honeywell Domonial Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-10P Manual de usuario

Honeywell

Honeywell Ademco Vista-48LA Instrucciones de funcionamiento

Honeywell

Honeywell VISTA-21iP Manual de usuario

Honeywell

Honeywell VISTA-32FBPT Manual de usuario

Honeywell

Honeywell RF Panic Button V2 Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-10P Instrucciones de montaje

Honeywell

Honeywell X-618 Manual de usuario

Honeywell

Honeywell Lynx Plus Series Manual de usuario

Honeywell

Honeywell Galaxy 2 Series Manual de usuario

Honeywell

Honeywell ADEMCO 4110XM Manual de usuario

Honeywell

Honeywell VISTA-32FBPT Instrucciones de montaje

Honeywell

Honeywell Galaxy 2-44+ Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario

This wireless siren/strobe is intended

for use with Honeywell controls that

support SiX™ series devices.

SiXSIREN

OPEN

Enroll

This device can be enrolled and programmed

either before or after installation.

1. Set the Lyric Smart Controller in Programming

Mode and go to Zone Programming. Select Add

New, then Serial Number. Follow the controller’s

instructions to begin enrollment.

2. Insert four 1.5V AA Lithium batteries (included) to

activate the device and begin the enrollment

process.

3. The SIXSIREN Green LED flashes rapidly during

enrollment (up to 20 seconds*)

*NOTE

: Depending on the signal strength between the

device and the controller, the enrollment period may

take longer than 20 seconds.

•The device sends its unique MAC ID address

(Serial Number) and Services information to

the controller.

•The controller registers the device and displays

the transmitter data on screen.

4. Enrollment is confirmed when the Green LED is

ON for 3 seconds and the controller chirps once.

5. Trigger the device tamper switch again to

complete enrollment.

6. The device did not enroll in the system if:

•The White LED flashes, the system chirps and

the device powers down.

•The Green LED flashes rapidly when the device

is removed from the mounting bracket (the

tamper switch is triggered).

To restart the enrollment process, ensure the

system is in programming mode and activate the

tamper switch.

NOTE

: Once enrolled in a system, the Siren cannot be

used with another controller until it is removed from

the current controller. See the Controller’s instructions

for details.

7. The device can also be manually enrolled. See

the Controller’s Programming Guide for

details.

BETA DRAFT II’s – 08/14/15

Gently twist the top of the

detector counterclockwise

and the mounting bracket

clockwise to separate them.

Program the SIXSIREN

Consult the Controller’s instructions for programming the device in the system.

Fault the device features to “Learn” the device “Services” in the control:

-Siren Chime Mode - Set sound level at the control:

•Low = 35Db1

•High = 55dB

•Life Safety2– select 85dB

-Cover tamper: The 10 minute tamper timer is reset every time tamper switch

closed and opened or the siren cover is opened.

-Temperature sensing – range is 0° – 120° F (-18° – 49° C); accuracy ±3° F (1.67° C)

35dB 1

55dB

85dB 2

1Factory default

Program

Mounting

NOTE

: Before mounting the device permanently,

conduct Go/No Go tests (see controller’s instructions)

to verify adequate signal strength and adjust the device

location and orientation as necessary.

The SIXSIREN can be mounted on the wall or on the

ceiling.

The rear tamper breakout MUST be mounted to a stud,

solid wood, or with a robust wall anchor.

Test the SIXSIREN

The SIXSIREN should be tested immediately after installation and at least once a year. Activate Test

Mode remotely from the Controller (see Controller’s manual for details).

Test Mode tests the sounder and LED:

-Sounder – the Burglary warble tone will sound for 3 seconds.

-LED – the White LED strobe will flash for 15 seconds.

Battery Replacement

•Twist the front cover counterclockwise and

separate it from the mounting bracket.

•Remove the batteries, wait 10 seconds and

insert

four new batteries

of the same type and brand

.

Recommended replacement batteries:

-1.5V AA Lithium Batteries [Non-Rechargeable]

-AA Alkaline batteries can be used, but battery

life will be significantly reduced.

NOTE

:

Do not mix old and new batteries,

battery types or manufacturers.

•Reattach the front cover and twist clockwise to

secure it in place.

BATTERY CAUTION

: Risk of fire, explosion and burns.

Do not recharge, disassemble, heat above 212 F (100 C) or

incinerate. Dispose of used batteries properly. Keep away

from children.

SIXSIREN LEDs and Sounder

Refer to the table below for operation of the four bi-colored LEDs and an 85dB sounder.

R / W

G / W

Sounder

Status

Green Rapid Flashes for

about 20 seconds, then ON

for 3 seconds

Chirps once

Power Up – Enrollment

Green Slow Flashing for 3

seconds

Chirps once Power Up – Device enrolled

Green ON for 20 seconds

System is Disarmed

Red ON for 20 seconds

System is Armed

Alternating Red and White

Flashing Strobe1(continues

until the Alarm is cleared)

Burglary

Warble ON for

3 seconds

Smoke or CO Alarm

White Strobe Flashing

White Strobe Flashing

Burglary

Warble ON for

3 seconds

Burglary Alarm

Red flashes once

every 45 seconds

2

Low Battery

Green Flashes slowly

for 10 minutes

Tamper Activated

1Strobe flash = two flashes per second, then OFF for 1 second.

2It is best to replace the battery BEFORE the chirping begins. Once started, the sounder continues to chirp until batteries are

replaced or die. See the Battery Replacement section.

Specifications:

Battery

:Four AA Lithium, Non-Rechargeable; Honeywell 462

Tamper

: Cover tamper

RF Frequency

: 2.4GHz

Operating Temperature

: 0° to 50° C / 32° to 122° F

Relative Humidity

: 95% max. (Agency compliance –93% max), non-condensing

Dimensions

: 14.14 cm Diameter x 4.62 cm Thick /

5.5 in. Diameter x 1.8 in. Thick

Weight

: xx oz (xx g)

Approval Listings:

FCC / IC

ETL Listed to UL985 / UL1023

cETL Listed to ULC-S545 &

ULC/ORD-C1023

RoHS

FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized

changes or modifications could void the user's authority to operate the equipment.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes:

(1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une

reception indésirable.

RF Exposure

Warning – The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and must

not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures.

Mise en Garde

Exposition aux Frequences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de séparation d'au moins 7,8 pouces (20 cm)

de toutes les personnes.

SUPPORT & WARRANTY

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING

LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

For the latest documentation and online support information, please go to:

https://mywebtech.honeywell.com/

For the latest warranty information, please go to:

www.honeywell.com/security/hsc/resources/wa.

MyWebTech

Warranty

2014 Honeywell International Inc. Honeywell and is a registered trademark of Honeywell International Inc.

All other trademarks are the properties of their respective owners. All rights reserved.

Ê800-15964kŠ

P/N 800-19202-5 11/15Rev A BETA

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security