Honeywell Fire-Lite Alarms ANN-80 Series Manual técnico

One Fire-Lite Place

Northford, CT 06472-1653 USA

203-484-7161 • FAX 203-484-7118

www.firelite.com

ANN-80 Series

Product Installation Document

PN 52749:D1 8/17/10 10-490

The ANN-80 Series Remote Fire Annunciators and Indi-

cators (ANN-80, ANN-80-W, ANN-80C) are compact,

backlit LCD displays designed for use with compatible

FACPs Fire Alarm Control Panels. The displays mimic

the FACP display and are capable of displaying English-

language text of system point status including device type,

independent point alarm, trouble or supervisory zone and

custom alpha labels programmed into the FACP. Refer to

the FACP manual installation section for detailed system

information and wiring.

NOTE: Installation and wiring must be done in

accordance with NFPA 72 and local ordinances.

Specifications

TB1 Terminals 1 & 2

Operating Voltage Range: 18 VDC to 28 VDC

Current Consumption @ 24 VDC nominal (filtered and

nonresettable):

• Normal/Standby (no activity): 37.0 mA

• Trouble Condition: 39.0 mA

• Alarm: 40.0 mA

• AC Fail (not backlit): 15.0 mA

TB1 Terminals 3 & 4

ANN-BUS rated at 5.5 VDC and 60 mA max.

Dimensions

6 7/8”W x 5 3/8”H x 1 3/8”D

Mounting

The ANN-80 Series plastic enclosures can be surface or

semi-flush mounted in a single, double or 4” square elec-

trical box.

To mount the ANN-80 Series enclosure:

1. Open the ANN-80 Series cover by turning the key

switch counterclockwise to the ON (Unlocked)

position.

2. Push in the snap latch tab located on the right side

while pulling the cover open.

3. Pull wire through 7/8” hole in backplate and feed

through wire channel to lower left corner of backplate

before routing to terminal block (refer to appropriate

FACP manual).

4. The cover must remain attached to the backplate

while mounting the annunciator to the electrical box/

wall. The cover cannot be reattached or removed

after the annunciator has been mounted.

5. If the cover should become detached from the

backplate, reattach as shown below.

6. Surface or Semi-flush mount the ANN-80 to a single,

double or 4” square electrical box. The

ANN-SB80KIT(-R/-B/-W) is an available kit that

contains two plastic backboxes that can be used to

surface mount the ANN-80 Series.

Backplate

Press in latch

and then

Pull open cover

Key switch shown

in OFF position

Cover with

LCD Display

Figure 1 Opening the ANN-80 Series

ann-80_iso2.wmf

ANN-80

Series

Cover

ANN-80

Series

Cover

ANN-80

Series

Backplate

ANN-80

Series

Backplate

• Position cover behind

backplate.

• Align hinge posts and

holes

• Slide holes down

onto posts.

• Close cover to lock

hinges into place.

Figure 2 Cover Reattachment

ann80doormount.wmf

2ANN-80 Series Installation Document — P/N 52749:D1 8/17/10

Wiring the ANN-80 Series to the FACP

Refer to Table 1 and Figure 3 for wiring connections.

Notes:

1. All connections/sources are to be power-limited and

supervised.

2. 12 - 18 AWG (0.75 - 3.25 mm2) wire for 24 VDC

circuit is acceptable.

3. Power wire distance limitation is set by 1.2 volt

maximum line drop from source to end of circuit.

4. Maximum distance from FACP to last ANN-BUS

device must not exceed 6,000 feet (1,800 m). Refer to

Wiring Distance Table in appropriate FACP manual

for wire gauge and distance limitations.

Setting the DIP Switches

Each ANN-BUS device requires a unique address.

ANN-80 Series DIP switch S21 is used to set the address.

This address will be displayed on the LCD display as the

Station ID number.

A maximum of 8 devices can be connected to the FACP

ANN-BUS communication circuit. ANN-BUS device

addresses do not need to be sequential and can be set to

any number between 01 and 08. Note that 00 is not a valid

address. The following illustrates the DIP switch settings

for each address (ID Number):

ANN-80 Series

Terminals (TB1)

FACP ANN-BUS

Terminals

Terminal 1 (-) (-)

Terminal 2 (+) (+)

Terminal 3 (A) A (ANN-BUS)

Terminal 4 (B) B (ANN-BUS)

Table 1 ANN-80 Series to FACP Connections

B (ANN-BUS)

A (ANN-BUS)

+ (24 VDC)

- (GND)

Connect to FACP ANN-BUS

and/or next device.

}

}Connect to FACP or UL Listed

Power Supply for Protective

Signaling and/or next device.

ANN-80 Series

Figure 3 Wiring the ANN-80 Series to an FACP

ann-80boardterms.wmf

ID Number

(Address)

(not valid) 00

DIP Switch S21

dipaddresses.wmf

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de Honeywell

Honeywell

Honeywell VISTA-128BPEN Instrucciones de montaje

Honeywell

Honeywell Ademco Lynx Touch Manual de usuario

Honeywell

Honeywell XL4600SM Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-40 Manual de usuario

Honeywell

Honeywell GENT Xenex Guía del producto

Honeywell

Honeywell ADEMCO VISTA-10P Instrucciones de montaje

Honeywell

Honeywell Gent Vigilon Compact Manual de usuario

Honeywell

Honeywell Galaxy 2 Series Manual de usuario

Honeywell

Honeywell ADEMCO VISTA SERIES Instrucciones de funcionamiento

Honeywell

Honeywell Esser 804950 Manual de usuario

Honeywell

Honeywell FG8MS Manual de usuario

Honeywell

Honeywell LYNX Touch 7000 Manual de usuario

Honeywell

Honeywell ADEMCO VISTA SERIES Instrucciones de funcionamiento

Honeywell

Honeywell ADEMCO VISTA-40 Instrucciones de funcionamiento

Honeywell

Honeywell Ademco VISTA-20P Instrucciones de funcionamiento

Honeywell

Honeywell LYNX Touch SIA Manual de usuario

Honeywell

Honeywell Lyric SIXSIREN Manual de usuario

Honeywell

Honeywell VISTA-128FBP Manual de usuario

Honeywell

Honeywell Lynx Plus Series Instrucciones de funcionamiento

Honeywell

Honeywell GKP-S8M Guía de configuración

Honeywell

Honeywell VISTA-250FBPT Instrucciones de montaje

Honeywell

Honeywell VAM Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-10P Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario