Honeywell Ademco VISTA-20P Instrucciones de funcionamiento

- 1 -

Step-by-Step

Tech Support

Updated 2/11/09

Programming Auto Arming and Disarming Schedules

The system provides schedules, which can be used to automatically control 11 types of system events at predefined

times. Some events are reserved for the installer only.

•VISTA-20P: Provides up to 32 schedules: 16 schedules for use by the end-user, 16 for use by the installer.

•VISTA-15P: Provides up to 8 schedules: 4 schedules for use by the end user, 4 for use by the installer.

•VISTA-10P: Provides up to 2 schedules: 1 schedule for use by the end-user, 1 for use by the installer.

NOTES:

•The master code can only access schedules 01-16 (VISTA-15P = 01-04) and events 00-07.

•System clock must be set before schedules can take effect. (See Page 2)

•Programmed schedules do not take effect until the next scheduled “start” time.

•The panel will NOT Auto Arm to a different state if already Armed

•There will be a Warning beep every 30 seconds for 10 minutes before the Auto Arming take effect. This

feature can not be disabled.

Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode.

ENTER SCHEDULE NO. Schedule Number

00=QUIT 01 VISTA-20P VISTA-15P

01-16 = End-User Schedules 01-04 = End User Schedules

17-32 = Installer-Only Schedules 05-08 = Installer-Only Schedules

Press [*] to continue

Enter Desired Schedule Number.

ENTER EVENT Enter Event

00 = Clear 05 = Forced Away Arming†

01 = Relay On/Off 06 = Auto Disarm

02 = User Access 07 = Display “Reminder”

03 = Latch key Report to Pager 10 = Display Custom Words

04 = Forced Stay Arming 11 = Periodic Test Report

Press [*] to continue

Enter the desired event for event you want to occur at a specified time.

†Forced bypass is automatically enabled regardless of the setting in field *23.

01 PARTITION Enter the desired partition that the auto arming window will occur on.

1 Entries:

1 = Partition 1 Only

2 = Partition 2 Only

0 = Partition 1 and 2

START S M T W T F S To enable the panel to Arm Away at 6:00PM Enter the start time as 6:00PM

06:00P 1 1 1 1 1 1 1

01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM; Days = place “1” under the days for

this event to take place. Press [*] to continue.

Enter the event’s start time and days off the week to occur.

To Select days, position the cursor under the desired days using the [*] key to move

forward, and then press “1” to select the day.

REPEAT OPTION Repeat Option

0-4 1 Entries:

0 = Do Not Repeat

1 = Repeat Weekly

2 = Repeat Biweekly (Every Other Week)

3 = Repeat Every Third Week

4 = Repeat Every Fourth Week

In our example we want the panel to arm at 6PM and we want it to happen every day of

the week. We enabled our time and every day in the start window. Now we want this

schedule to take place every day of the week every week. So our entry would be a 1 in

this location.

ENTER SCHEDULE NO. Quitting

00=QUIT 00 Enter 00 then * to quit.

- 2 -

Step-by-Step

Tech Support

Updated 2/11/09

Setting the System Clock

The next step in the process is to set the system clock. To do so enter installer code + [#] + [6] [3] while in normal

operating mode.

•ALL partitions must be disarmed before you can set the system clock.

DISARMED

At the Disarmed Ready to Arm Screen Enter Installer code # 63

READY TO ARM

TIME/DATE TUE Current Time Display

12:00AM 01 / 01 / 00 Press [*] to Enter. When doing so you will see a flashing curser under the hour’s slot.

TIME/DATE TUE Time/Date Editing display

03:16P 2009/02/10 Entries:

•Enter 2 digit hours

•Enter 2 digit minute

•Enter 1 for PM and 2 for AM

•Enter 2 last 2 digits for the year

•Enter 2 digit Month

•Enter 2 digit Day

Enter [*] to exit or wait 30 seconds.

Testing the Auto Arming Window

To test the Auto Arming Schedule set the system clock 2 minute before the panel is suppose to auto arm and let it

roll into the window. Our panel is going to arm at 6PM so we will set our clock to 5:58PM. You can not program

the time for 6PM or greater and expect it to arm. As stated above the panel must roll into the time window.

What will prevent Auto Arming of the panel?

Panel Status Yes No

RF Supervision Error 9

Transmitter Tamper 9

Expander Supervision 9

Expander Tamper 9

Fire Alarm 9

Fire Alarm Memory 9

Fire Trouble 9

Burglar Alarm 9

Alarm Memory 9

What to look for if an Auto Arm fails

The table above explains when the panel prevents an auto arm; the only situations the panel will not arm is because

of any Alarm or Alarm memory. If you were trying to arm the panel from the keypad (not auto arming) it would

require you to disarm the system 2 times. Auto Arming is no different. The 1st time is for the silence

(acknowledgement) and the 2nd time to clear the Trouble or Alarm condition.

The Work Around

We must create 2 time windows to disarm before the actual auto arming of the panel. If we need the panel to auto

arm at 6PM, then we will create 2 more schedules. 1st schedule to disarm at 5:58PM and the 2nd schedule to disarm

again at 5:59PM, so to sum it up we would need 3 schedules:

2. Auto Disarm (Event #06) at 5:58 PM Sat-Sun, Weekly ÆSilences/Acknowledges the Alarm/Trouble.

3. Auto Disarm (Event #06) at 5:59 PM Sat-Sun, Weekly ÆResets the Alarm/Trouble Memory.

4. Auto Arm (Event #05) at 6:00 PM Sat-Sun, Weekly ÆArms the panel.

Otros manuales para Ademco VISTA-20P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de Honeywell

Honeywell

Honeywell ADEMCO VISTA-10P Manual de usuario

Honeywell

Honeywell Evohome Manual de usuario

Honeywell

Honeywell Vista 21IP Manual de usuario

Honeywell

Honeywell SUGPACK-UK Manual de usuario

Honeywell

Honeywell sixsiren Manual de usuario

Honeywell

Honeywell FA-300 Alarm Bar Manual de usuario

Honeywell

Honeywell Ademco Vista-48 series Manual de usuario

Honeywell

Honeywell Accenta Series Guía de inicio rápido

Honeywell

Honeywell LYNX TouchL5200 Series Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-40 Instrucciones de montaje

Honeywell

Honeywell Code Encryptor II Manual de usuario

Honeywell

Honeywell INTELLIGUARD 9000 Manual de usuario

Honeywell

Honeywell SILENT KNIGHT RA-2000 Manual de usuario

Honeywell

Honeywell TCPA2B Manual de usuario

Honeywell

Honeywell ADEMCO VISTA SERIES Instrucciones de montaje

Honeywell

Honeywell First Alert FA168CPS Manual de usuario

Honeywell

Honeywell Galaxy Dimension Manual de usuario

Honeywell

Honeywell LYNX Touch Series Instrucciones de montaje

Honeywell

Honeywell VISTA-128BPT Instrucciones de montaje

Honeywell

Honeywell Friedland HISK1 Manual de usuario

Honeywell

Honeywell X-618 Manual de usuario

Honeywell

Honeywell VISTA 15P - Ademco 6 Zone Control Panel Manual de usuario

Honeywell

Honeywell Gamewell-FCI E3 Series Manual de usuario

Honeywell

Honeywell VISTA-128BP Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario