Honeywell LKS 131 Manual de usuario
1 EN2C-0111SZ20 R0202
PRODUCT HANDBOOK
ACTUATOR
LKS 131
FOR AIR DAMPERS ON SINGLE, DUAL STAGE AND
MODULATING BURNERS
CONTENTS
GENERAL
Description ................................................................. 2
Features ...................................................................... 2
TECHNICAL DATA
Specification ............................................................... 3
Dimensional drawings ................................................ 4
INSTALLATION AND OPERATION
Installation and final checkout .................................... 5
Circuit diagrams ......................................................... 6
VARIOUS
Standards and approvals ........................................... 7
Ordering information .................................................. 7
Accessories ................................................................ 7
APPLICATION
The LKS 131 air damper actuator is designed to be fitted to
multi-stage or modulating oil and gas burners with fully
closed position.
EN2C-0111SZ20 R0202 2
A synchronous motor powers an output shaft and a backlash-
free cam shaft via a gear reducer.
The cam shaft operates limit and auxiliary switches. The
GENERAL
Electric actuator up to 0.6 Nm
• Drive times: 3 ... 38 sec.
• Variants: - clockwise or counter clockwise rotation
- with integrated electronic circuitry
- shaft version
DESCRIPTION
position at which one of the limit or auxiliary switches operates
can be adjusted steplessly within the operating range using
the associated cam disc. Spindle-driven cams, which can be
adjusted with a screwdriver, are available.
FEATURES
• Internal position indicator
• Easily adjustable limit and auxiliary switches
• Synchronous motor
3 EN2C-0111SZ20 R0202
Diagram Shaft Drive Load torque Holding Voltage Type Remarks
time torque
Nr. Nr. s Nm Nm V
S3 2 5 0,6 0,4 230 LKS 131-05 B 2-5 S3
S3.1 2 5 0,6 0,4 230 LKS 131-08 B 2-5 S3.1 Without plug
S6 2 5 0,6 0,4 230 LKS 131-09 B 2-5 S6 On/off movement only
S3 2 38 0,6 0,4 230 LKS 131-12 B 2-38 S3
S8 6 15 0,6 0,4 230 LKS 131-15 B 6-15 S8 Limit switch and potentiometer 1k
S5 6 15 0,6 0,4 230 LKS 131-16 B 6-15 S5
S20-2 6 38 0,6 0,4 230 LKS 131-17 B 6-38 S20-2 With special 8 mm shaft
S3 6 5 0,6 0,4 230 LKS 131-18 B 6-5 S3 With special 8 mm shaft
2) 3)
4)
6)
5)
7)
Technical Data
Housing
•impact-proof, heat-resistant synthetic material
Colour: black
Drive motor
•reversible synchronous motor
Switch point setting
•via stepless cam setting, spindle-driven cam with
superimposed scale
Position indicator
•via co-rotating scale (under the cover)
Connection system
•fixed cable connection with 9-pin plug
Gearing
•spur gearing, maintenance-free
Output shaft
•standard plastic, interior square 8 mm
Fitting and fastening
•Fastened from inside via tapped M 5 through-holes
PCBs
•for all electrical functions, increased conductor thickness
Mains voltage
•230 V -15% +10% or
110 V -15% +10%
Mains frequency
•50 Hz or 60 Hz
Safety class
•II VDE 0631
Power consumption
•approx. 9 VA
Duty cycle
•50% in 2 minutes
Interference suppression
•N (according to VDE 0785)
Actuating angle
•max. 90°
Mounting position
•any
Protection
•IP40, with appropriate design of the cable entries and
screw fastening (DIN 40050)
Cable connection
•via 9-pin AMP socket connector
1)
SPECIFICATION
TECHNICAL DATA
counter clockwise rotation
Type overview
Legend
1) when viewing from direction A (see dimensional drawing)
2) see “Circuit diagrams”
3) see “Dimensional drawing”
4) at 50 Hz for 90°
at 60 Hz, Drive times are about 20 % shorter
5) under nominal conditions
under extreme conditions (e.g. +60 °C, 230V -15%) the torques will be 25% lower
6) +10% -15%; 50...60Hz
at -15%; torque reduced by approx. 20% at undervoltage
7) Standard: Lever-operated cam
EN2C-0111SZ20 R0202 4
DIMENSIONAL DRAWING
8,5
47
62
100
60
D) Fixing hole
through-hole 5,3 mm inside dia
85
D25,2
6,5
1
14
8
cable output
Direction of rotation
•see “Type overview”
Torque and holding torque
•see “Type overview”
Drive times
•5, 15, 38 sec. for 90°
Limit and auxiliary switches
•max. 7
operation with adjustable cam discs, cams coloured in
normal way:
blue fully closed position
orange low load
red high load
black spare switches for additional functions
•switching voltage
AC 24....230 V
•switching capacity
with inductive loads 250 VA
Ambient temperature
•operation 0 ... +60°C
•transport and storage -20 ... +60°C
Condensation, icing and exposure to water not
permitted
Weight
• approx. 500 g
A
5 EN2C-0111SZ20 R0202
• The regulations and standards applicable in each
particular case must be observed.
• Installation and commissioning must only be
carried out by qualified technicians.
• Electrical wiring must comply with national and
local regulations.
• Always lay the burner ignition cable separately
and as remotely as possible from the device and
other cables.
• Carefully check all cabling and wiring prior to
commissioning.
• Disconnect the actuators completely from the
power supply when working close to terminals
and connections.
• Screw the housing cover securely in place to
provide shock-hazard protection on the actuator
and all electrical connections.
• Electromagnetic emissions must be checked on
a case by case basis.
INSTALLATION AND OPERATION
INSTALLATION AND FINAL CHECKOUT
EN2C-0111SZ20 R0202 6
CIRCUIT DIAGRAMS
S4
S3
S5 S6
S7 S8
7 EN2C-0111SZ20 R0202
LKS 131-09 B 2 - 38 S3
Circuit version
Drive time for 90°
5 s
15 s
38 s
Type of drive shaft
1Interior square 8 mm
2Interior square 8 mm or any angle
6Special shaft, e.g. round 6
Direction of rotation
Aclockwise
Bcounter-clockwise
Model
Series
Not for creation of new type
Conformity
• In accordance with EU Directives 73/23/EU
and 93/68/EU. Conforms to
EN 60730 – 1 : 1991 A1 and A11 : 1991
EN 60730 – 2 – 5 : 1991
ORDERING INFORMATION
Special versions with potentiometer on request
STANDARDS AND APPROVALS
ACCESSORIES
VARIOUS
Tabla de contenidos
Otros manuales de Controladores de Honeywell
Honeywell
Honeywell Excel 10 Manual de usuario
Honeywell
Honeywell ML4125 Manual de operación
Honeywell
Honeywell ML7430E Manual de usuario
Honeywell
Honeywell Aquastat L7224U Manual de usuario
Honeywell
Honeywell ML6161E Manual de usuario
Honeywell
Honeywell HC900 Guía del usuario
Honeywell
Honeywell CIPer 50 Manual de usuario
Honeywell
Honeywell FAST-ACTING, TWO-POSITION ACTUATORS ML4202 Manual de usuario
Honeywell
Honeywell TBC2800 Series Manual de usuario
Honeywell
Honeywell S7014A Series Manual de usuario
Honeywell
Honeywell ML9185 Manual de usuario
Honeywell
Honeywell S05 Series Manual de usuario
Honeywell
Honeywell CentraLine EAGLEHAWK NX Manual de usuario
Honeywell
Honeywell WV8860C Manual de usuario
Honeywell
Honeywell Sieger System 57 Manual de usuario
Honeywell
Honeywell DCP 250 Guía de instalación
Honeywell
Honeywell ML6984 Manual de usuario
Honeywell
Honeywell 10260S series Guía
Honeywell
Honeywell Air Alert 96d Manual de usuario
Honeywell
Honeywell HC900 Manual de usuario
