Honeywell Velociti AOM-2RF Manual de usuario

AOM-2RF Relay Control Module

INSTALLATION AND MAINTENANCE INSTRUCTIONS

BEFORE INSTALLING

This information is included as a quick reference installation guide. Refer to

the appropriate Gamewell-FCI control panel installation manual for detailed

system information. If the modules will be installed in an existing operational

system, inform the operator and local authority that the system will be tem-

porarily out of service. Disconnect power to the control panel before installing

the modules.

NOTICE: This manual should be left with the owner/user of this equipment.

GENERAL DESCRIPTION

The AOM-2RF Relay Control Module is intended for use in intelligent, two-

wire systems where the individual address of each module is selected using

the built-in rotary switches. It allows a compatible control panel to switch

discrete contacts by code command. The relay contains two isolated sets of

Form-C contacts, which operate as a DPDT switch and are rated in accordance

with the table in the manual. Circuit connections to the relay contacts are

not supervised by the module. The module also has a panel controlled LED

indicator. This module can be used to replace a AOM-2 module that has been

configured for Form-C operation.

COMPATIBILITY REQUIREMENTS

To ensure proper operation, this module shall be connected to a compatible

Gamewell-FCI system control panel (list available from Gamewell-FCI).

SPECIFICATIONS

Normal Operating Voltage: 15 to 32 VDC

Maximum Current Draw: 6.5 mA (LED on)

Average Operating Current: 230µA (LED flashing) Velociti Mode; 255µA (LED flashing) CLIP Mode

EOL Resistance: Not used

Temperature Range: 32˚F to 120˚F (0˚C to 49˚C)

Humidity: 10% to 93% Non-condensing

Dimensions: 4.675" H x 4.275" W x 1.4" D (Mounts to a 4˝ square by 21/8˝ deep box.)

Accessories: SMB500 Electrical Box; CB500 Barrier

I56-3551-006

Velociti ®Series

FIGURE 1. CONTROLS AND INDICATORS:

C1071-00

RELAY CONTACT RATINGS:

CURRENT RATING MAXIMUM VOLTAGE LOAD DESCRIPTION APPLICATION

2 A 25 VAC PF = 0.35 NON-CODED

3 A 30 VDC RESISTIVE NON-CODED

2 A 30 VDC RESISTIVE CODED

0.46 A 30 VDC (L/R = 20MS) NON-CODED

0.7 A 70.7 VAC PF = 0.35 NON-CODED

0.9 A 125 VDC RESISTIVE NON-CODED

0.5 A 125 VAC PF = 0.75 NON-CODED

0.3 A 125 VAC PF = 0.35 NON-CODED

12 Clintonville Road

Northford, CT 06472-1653

Phone: 203.484.7161;

Fax: 203.484.7118

www.gamewell-fci.com

1 I56-3551-006

02-14

WARNING

All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during shipping. To ensure that

the switch contacts are in their correct state, modules must be made to communicate with the panel before connecting circuits controlled by the module.

FIGURE 3. RELAY MODULE WIRING DIAGRAM:

MODULE

FROM PANEL OR

(+)

(–)

TO NEXT

(+)

(–)

DEVICE

(+)

(–)

CONTROL

CONNECT MODULES TO LISTED COMPATIBLE

RELAY COMMON 1

RELAY COMMON 2

NORMALLY CLOSED 1

NORMALLY OPEN 2

NORMALLY CLOSED 2

MODULE DOES NOT SUPERVISE CONTROLLED CIRCUITS

NORMALLY OPEN 1

CONTROL PANELS ONLY

PREVIOUS DEVICE

SIGNAL LINE CIRCUIT (SLC)

32 VDC MAX.

TWISTED PAIR

IS RECOMMENDED

UNUSED

*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.

IF ANY WIRING TO TERMINALS 4 – 10 IS NONPOWER

LIMITED, THE CB500 BARRIER IS REQUIRED. THE CB500

INCLUDES A NONPOWER LIMITED LABEL, WHICH MUST

BE PLACED OVER THE POWER LIMITED TERMINAL

INFORMATION ON THE NAMEPLATE LABEL.

C0946-00

MOUNTING

The AOM-2RF mounts directly to 4-inch square electrical boxes (see Figure

2A). The box must have a minimum depth of 21/8inches. Surface mounted

electrical boxes (SMB500) are available from Gamewell-FCI. The module can

also mount to the DNR(W) housing.

FIGURE 2A. MODULE MOUNTING FIGURE 2B.

WITH BARRIER:

C1070-00

WIRING

NOTE: All wiring must conform to applicable local codes, ordinances, and reg-

ulations. When using control modules in nonpower limited applications, the

CB500 Module Barrier must be used to meet UL requirements for the separa-

tion of power-limited and nonpower-limited terminals and wiring. The barrier

must be inserted into a 4˝ × 4˝ × 21/8˝ junction box, and the control module

must be placed into the barrier and attached to the junction box (Figure 2A).

The power-limited wiring must be placed into the isolated quadrant of the

module barrier (Figure 2B).

1. Install module wiring in accordance with the job drawings and appropri-

ate wiring diagrams.

2. Set the address on the module per job drawings.

3. Secure module to electrical box (supplied by installer), as shown in

Figure 2A.

Wire should be stripped to the appropriate length (recommended strip length

is 1/4“ to 3/8”). Exposed conductor should be secured under the clamping plate

and should not protrude beyond the terminal block area. Caution: Do not loop

wire under terminals. Break wire run to provide supervision of connections.

2 I56-3551-006

Velociti®, Gamewell-FCI®, System Sensor®, and Honeywell®are registered trademarks of Honeywell International, Inc.

Este manual sirve para los siguientes modelos

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell SmartPAC 2 Manual de usuario

Honeywell

Honeywell V4297A Series Manual de operación

Honeywell

Honeywell NOTIFIER FTM-1 Manual de usuario

Honeywell

Honeywell MasterLogic 50 Series Manual de usuario

Honeywell

Honeywell SLATE Manual de usuario

Honeywell

Honeywell MV300 Manual de usuario

Honeywell

Honeywell V5852A Manual de servicio

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell SV2 Series Manual de usuario

Honeywell

Honeywell BCU 370 Manual

Honeywell

Honeywell SDW 10 Manual de servicio

Honeywell

Honeywell Aquatrol W964F Manual del propietario

Honeywell

Honeywell HS10S Manual de usuario

Honeywell

Honeywell V4295A,S Manual de usuario

Honeywell

Honeywell NOTIFIER M701E Manual de usuario

Honeywell

Honeywell FV300 Manual de usuario

Honeywell

Honeywell CentraLine CLIOL822A Manual de operación

Honeywell

Honeywell Silent Knight SK-Relay-6 Manual de usuario

Honeywell

Honeywell DCCC6500 Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell NetAXS-123 Manual de usuario

Honeywell

Honeywell VR4920Z 1000 Manual de usuario

Honeywell

Honeywell V-Plex ADEMCO 4297 Instrucciones de montaje

Honeywell

Honeywell ControlEdge 900 platform Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario