Honeywell Prestige THX9421R02 Manual de usuario

Prestige®IAQ

with Equipment Interface Module

Installation Guide

2 Wires for Power

RedLINK to Equipment Interface Module

RedLINK to TrueZONE Wireless Adapter

69-2739_A.indd 1 11/1/2012 2:33:23 PM

Current display. Button pressed in

signifies current display

Mode control buttons. Use to change

settings for Fan or System Heat/Cool.

Menu. Select options to: set schedules,

view equipment status, change IAQ

settings, access installer options*, etc.

Current schedule. Shows desired

temperature and schedule status.

Indoor conditions. Shows indoor

temperature and humidity.

Current date and time.

Current status. Shows system mode

(heat/cool), outdoor temperature and

humidity (with optional outdoor sensor).

USB port. Use USB device to load

settings and dealer information.

Reference to key features

* Password is date code.

Getting started

Follow these basic steps to install this

thermostat, link it with the equipment interface

module (EIM) and wireless accessories and

set installer options.

1 Installing the Equipment Interface

Module (EIM)

2 Installing the thermostat

3 Powering optional RedLINK accessories

4 Performing initial setup

5 Finding your password (Date Code)

• To add or remove RedLINK accessories

• To make changes to Installer Setup

• To perform an Installer Test

• To view Data Logs

1324

Thermostat (back view)

Password

(Date Code)

69-2739_A.indd 2 11/1/2012 2:33:24 PM

NOTE: If an EIM is mounted inside a metal cabinet, it is recommended to use

a THM4000R1000 Wireless Adapter for extended wireless range. Mount the

Wireless Adapter outside the metal cabinet and connect to the ABCD terminals at

the EIM.

NOTE: When installing multiple

thermostats and EIMs, mount the

EIMs at least 2 feet apart for best

RedLINK performance.

1.1 Mount EIM.

Mount the EIM near the HVAC

equipment or on the equipment

itself.

Use screws and anchors as

appropriate for the mounting

surface.

1.2 Wire EIM as shown.

Refer to the table and wiring diagrams on pages 3-5.

NOTE: If you are installing discharge and return air sensors, refer to the mounting

instructions in the Alerts and Delta T Diagnostics Installation Instructions packed

in the kit.

Installing the equipment interface module (EIM)

Terminal Designations

Conventional System Heat Pump

Terminal Description Terminal Description

CCommon wire from 24 VAC

transformer. CCommon wire from 24 VAC

transformer.

R* Power wire from 24 VAC

transformer. RPower wire from 24 VAC

transformer.

RH* Heating power. RH Heating power.

RC* Cooling power. RC Cooling power.

W Heat Stage 1 O/B Changeover valve for heat pumps.

W2 Heat Stage 2 AUX 1 Backup Heat Stage 1/Emergency

Heat Stage 1

W3 Heat Stage 3 AUX 2 Backup Heat Stage 2/Emergency

Heat Stage 2

Y Compressor Stage 1 Y Compressor Stage 1

Y2 Compressor Stage 2 Y2 Compressor Stage 2

G Fan Relay G Fan Relay

AConnect to Economizer Module or

Lighting Panel (TOD). L/A

Connect to Compressor Monitor,

Zone Panel, Economizer Module or

Lighting Panel (TOD).

* Remove jumpers when separate transformers are used.

O/B

AUX1

AUX2

L/A

69-2739_A.indd 3 11/1/2012 2:33:25 PM

Terminal Designations

Conventional System Heat Pump

Terminal Description Terminal Description

U1 / U1**

U2 / U2**

U3 / U3**

Universal relay for humidification,

dehumidification, ventilation, or

a stage of heating/cooling. U

terminals are dry contacts that

require power.

U1 / U1**

U2 / U2**

U3 / U3**

Universal relay for humidification,

dehumidification, ventilation, or

a stage of heating/cooling. U

terminals are dry contacts that

require power.

S1 / S1***

S2 / S2***

S3 / S3***

S4 / S4***

Universal input for a wired indoor

sensor, outdoor sensor, discharge

sensor, return sensor, dry contact

device for alerts or dry contact

device for remote setback.

S1 / S1***

S2 / S2***

S3 / S3***

S4 / S4***

Universal input for a wired indoor

sensor, outdoor sensor, discharge

sensor, return sensor, dry contact

device for alerts or dry contact

device for remote setback.

Connect to THM4000R1000

Wireless Adapter for extended

wireless range.

Connect to THM4000R1000

Wireless Adapter for extended

wireless range.

** See wiring diagrams on pages 4-5.

*** See wiring diagram below for wiring Dry Contact Devices to display alerts.

U1, U2, and U3 are normally

open dry contacts when set up

for a stage of heating or cooling.

Youmustinstallaeldjumperif

the stage of heating or cooling is

former.DoNOTinstallaeld

jumper if the stage of heating has

its own transformer.

120

VAC

HEAT STAGE 3,

COOL STAGE 3,

COOL STAGE 4 OR

GEOTHERMAL

RADIANT HEAT

TRANSFORMER

Wiring dry contact devices to display alerts

DISCONNECT POWER BEFORE INSTALLATION.

Do not apply power to S1, S2, S3 or S4 terminals.

NOTE: The dry contact device must

be rated for low voltage.

Connect a dry contact device such as a

water sensor to S1, S2, S3 or S4 terminals.

The thermostat displays an alert when a

problem is detected.

MULTIPLE DRY CONTACT DEVICES

ON ONE SET OF TERMINALS

EIM

ONE DRY CONTACT DEVICE

Connecting a stage of heating or cooling to a universal relay

(U1, U2, U3)

69-2739_A.indd 4 11/1/2012 2:33:26 PM

POWERED

HUMIDIFIER

VAC

120

VAC

120

VAC

FIELD INSTALLED

JUMPER BETWEEN

R AND U1

24 VAC

NON-POWERED

HUMIDFIER

VAC

120

VAC

POWERED

VENTILATOR

VAC

120

VAC

120

VAC

POWERED

DEHUMIDIFIER

VAC

120

VAC

120

VAC

FIELD INSTALLED

JUMPER BETWEEN

R AND U1

24 VAC

NON-POWERED

VENTILATOR

VAC

120

VAC

FIELD INSTALLED

JUMPER BETWEEN

R AND U1

24 VAC

DEHUMIDIFICATION

WITH LOW SPEED FAN

VAC

120

VAC

Typicalhookupofpoweredhumidier Typical hookup of non-powered

humidier

Typical hookup of powered ventilation

Typicalhookupofpowereddehumidier

(whole house dehumidifer)

Typical hookup of variable speed blower

fordehumidicationinlowspeed

Typical hookup of non-powered

ventilation

Any combination of universal relays (U1, U2, U3) can be used. They are set in the

thermostat installer setup.

WiretheuniversalEIMrelaytothelowspeedfanfordehumidicationcontrolat

the equipment. The EIM relay can be set to be normally open or normally closed

in the thermostat installer setup.

Normally open, dry contacts

Normally closed, dry contacts

Wiring humidification, dehumidification and ventilation

69-2739_A.indd 5 11/1/2012 2:33:28 PM

2.1 Separate wallplate

from thermostat.

2.2 Mount wallplate as shown.

Mount new wallplate using

screws and anchors included

with the thermostat.

Drill 3/16-in holes for drywall.

Drill 7/32-in holes for plaster.

2.3 Connect power to

thermostat.

2.3a Connect thermostat to

the R and C terminals at

the EIM or to a separate

24 volt transformer (not

provided).

2.3b Push excess wire back

into the wall opening.

2.4 Insert coin cell battery.

Place coin cell battery in

thermostat as shown with +

side up.

NOTE: Coin cell battery saves

time and date during a power

loss.

2Installing the thermostat

1324

Thermostat (back view)

Wallplate (back view)

Wallplate

Coin cell

battery

1324

69-2739_A.indd 6 11/1/2012 2:33:29 PM

3.1 Install batteries in RedLINK

accessories.

• Portable Comfort Control

• Wireless Outdoor Sensor*

• Wireless Indoor Sensor*

• Wireless Entry/Exit Remote*

• Wireless Vent and Filter Boost

Remote*

* Requires setup. See Installer

Setup options in Step 4.5.

3.2 Connect gateway to internet and

connect to power.

3.2a Connect RedLINK Internet

Gateway to router or modem

with Ethernet cable (RJ45).

3.2b Connect gateway’s power cord

to an electrical outlet that is not

controlled by a wall switch.

3Powering optional RedLINK accessories

Thermostat

Wallplate

2.5 Mount thermostat on

wallplate.

Align thermostat to wallplate

and snap into place.

3.2a

3.2b

69-2739_A.indd 7 11/1/2012 2:33:30 PM

4Performing initial setup

Initialsetupoptionsdenethetypeofsystemyouareinstalling:

• Residential or commercial

• Non-zoned or zoned

• Used with or without an Equipment Interface Module (THM5421)

• Used with or without the TrueZONE Wireless Adapter (THM4000)

4.2 Link the thermostat to the equipment

interface module.

4.2a Press and quickly release the

CONNECT button on the EIM.

Make sure the “Connected” light is

flashing green.

NOTE: If the “Connected” light does

NOT flash green, another system may

be in the listening mode. Please exit the

listening mode at the other system and

then try again.

• Green Flashing: In Listening

Mode - system is ready to add

RedLINK devices.

• Green Steady: RedLINK devices are

communicating.

• Red: RedLINK device(s) are NOT

communicating. Check EIM and

RedLINK devices.

4.2b While the “Connected” light is

flashing green on the EIM, press

Next on the thermostat. After a

short delay, the screen will display

Device Connected.

4.1 Follow prompts on the screen to

select appropriate options.

NOTE: If you are connecting the

thermostat to the TrueZONE Wireless

Adapter (THM4000), refer to the

TrueZONE instructions to link the

thermostat and RedLINK accessories.

Then go to step 4.5. Next

CONNECT

CONNECTED

69-2739_A.indd 8 11/1/2012 2:33:31 PM

4.3 When you see the prompt Do you

have RedLINK accessories to

connect? Touch Yes or No.

• If you select Yes, you will be

prompted to Press Connect on all

new accessories. Continue to Step

4.4.

• If you select No, continue to Step 4.5.

4.4 Connect each RedLINK accessory.

NOTE: Make sure accessories are at

least 2 feet away from the EIM during

the linking process.

4.4a While the Add Device screen

is displayed (listening mode),

press and quickly release the

CONNECT button on each new

RedLINK accessory.

4.4b After a short delay (up to 20

seconds), check the thermostat

to confirm the connection of each

RedLINK accessory.

4.4c Touch Done at the thermostat after

all new RedLINK accessories are

connected.

NOTE: The thermostat displays a

countdown timer while in listening

mode. If it detects no activity for 15

minutes, it exits listening mode.

Done

4.5 Finish the initial setup.

Finish the setup by selecting the

desired options. Touch Done after

you select the last option you want to

change.

The thermostat now displays its Home

screen and the thermostat setup is

complete.

Listening mode

69-2739_A.indd 9 11/1/2012 2:33:31 PM

5Finding your password (Date Code)

• To add or remove RedLINK accessories

• To make changes to Installer Setup

• To perform Installer Test

• To view Data Logs

Finding your password

You can find the Date Code on the

back of the thermostat, or

1 Touch Menu.

2 Select Dealer Information.

Dealer Informa�on

1324

Thermostat (back view)

Password

(Date Code)

69-2739_A.indd 10 11/1/2012 2:33:31 PM

Tabla de contenidos

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell SM110 Manual de usuario

Honeywell

Honeywell VQ400 Series Manual de usuario

Honeywell

Honeywell TS131 Manual de usuario

Honeywell

Honeywell S8600 Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell T7270A2001 Manual de usuario

Honeywell

Honeywell AlarmNet 7845i-GSM Instrucciones de montaje

Honeywell

Honeywell S4965 Series Manual de usuario

Honeywell

Honeywell Pro-Watch 7000 Manual de usuario

Honeywell

Honeywell GSMVLP5-4G Instrucciones de montaje

Honeywell

Honeywell TRADELINE VR8345M Manual de usuario

Honeywell

Honeywell SG160S Manual de usuario

Honeywell

Honeywell V48F Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell S4567A 1001 Manual de usuario

Honeywell

Honeywell V5055A Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell VC Series Manual de usuario

Honeywell

Honeywell PS300 Manual de usuario

Honeywell

Honeywell MAXON 8730 Series Manual de usuario

Honeywell

Honeywell BA295 Compact Manual de usuario

Honeywell

Honeywell L506 Manual de usuario

Honeywell

Honeywell Satronic DMG 973 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario