Honeywell BSM Instrucciones de montaje

K14864V3 9/10 Rev. A

BSM

Battery Sense Module

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The Honeywell Battery Sense Module is a control panel

accessory that is used to monitor and report the backup

battery status. Its features are:

Monitors and reports for one or two batteries.

Detects and reports low battery conditions.

Detects and reports if a battery is removed.

Provides deep discharge battery protection if AC

power is lost and the backup battery voltage falls

below a safety threshold of 9.5 to 10 volts.

Additional modules can be used for those control panels

that use additional batteries.

PACKAGE CONTENTS

The following items are included:

Battery Sense Module with bracket

Battery Harness (qty 2)

Summary of Connections label

SPECIFICATIONS

Physical: 3-1/8” L x 2-3/4” W x 3/4” H

(80mm x 70mm x 20mm)

Electrical:

Input Voltage: 12VDC nominal (from control panel)

Input Current: 20mA (max used by BSM)

Current Handling Capability: 2.3A maximum

(Control panel load must not exceed 2.3A.)

INSTALLATION

1. Select a suitable area in the control panel where

the mounting will not interfere with testing or

servicing of other components.

2. Clip the Battery Sense Module to the cabinet edge.

CONNECTIONS

1. Refer to the Connections Diagram on other side.

When connecting leads, support the module to

prevent stress on the circuit board.

2. Connect the module's power leads to the control

panel's 12VDC backup battery power terminals.

3. Connect backup battery A to the module. Then

connect backup battery B (if present) to the module.

4. If only one backup battery is being used, depress

the ENROLLMENT switch to toggle the Battery

Sense Module to sense only one battery.

ULC

When used with one battery and the total

load is greater than 1.5A, jumper the

Battery A terminals and the Battery B

terminals on the Battery Sense Module to

the backup battery.

5. For non-Honeywell control panels, connect the

ZONE OUT to an unused control panel zone. (Do

not use a fire zone.)

Note: For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT terminal on

the BSM. The Honeywell control panel will

automatically detect a low or missing battery

through the panel's battery cable.

6. Affix the supplied Summary of Connections label to

the inside of the control panel.

CONFIGURATION

1. Refer to the control panel's installation guide for

details on fault monitoring.

2. For non-Honeywell control panels, program the

connected zone for the Battery Sense Module to

detect an active high fault condition.

ZONE OUT

BAT

BSM-001-V0

B AT. A PANEL

B AT. B

DOCUMENTATION AND ONLINE SUPPORT

For the latest documentation and online support information, please go to:

http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY

For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ÊK14864V3cŠ

K14864V3 9/10 Rev. A

STATUS LEDs (A and B)

STEADY ON Battery is present and good.

BLINKING Battery is programmed to be

present, and is NOT present.

OFF Battery is NOT programmed to be

present.

ENROLLMENT Switch

Default condition is for 2

batteries.

Depress once for 1 battery.

To the control panel battery terminals.

To Battery A terminals.

To Battery B terminals.

To a non-Honeywell

control panel zone for

fault monitorin

Note:

For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT ter-

minal on the BSM. The Honeywell

control panel will automatically detect

a low or missing battery through the

panel's battery cable.

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell SUPER TRADELINE S8610U Manual de usuario

Honeywell

Honeywell BA298I-F Manual de usuario

Honeywell

Honeywell VP513A Manual de usuario

Honeywell

Honeywell W7212 Manual de operación

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell NOTIFIER M710E-CZ Manual de usuario

Honeywell

Honeywell NOTIFIER M710-CZR Manual de usuario

Honeywell

Honeywell DS06D Manual de operación

Honeywell

Honeywell V4295A,S Manual de usuario

Honeywell

Honeywell Ex-Or MLSUC500 Manual de usuario

Honeywell

Honeywell TrueZONE ARD Series Manual de usuario

Honeywell

Honeywell CIPer 30 Manual de usuario

Honeywell

Honeywell Braukmann BV300 Manual de usuario

Honeywell

Honeywell RM7823A Manual de usuario

Honeywell

Honeywell DCCC6500 Manual de usuario

Honeywell

Honeywell FF-SRE6029 Manual de usuario

Honeywell

Honeywell BCU 370 Manual

Honeywell

Honeywell V4043A Manual de usuario

Honeywell

Honeywell Notifier FCM-1 Manual de usuario

Honeywell

Honeywell ERM5220R1018 Manual de usuario

Honeywell

Honeywell NETAXS NX4L1 Manual de usuario

Honeywell

Honeywell ADEMCO 4204 Manual de usuario

Honeywell

Honeywell VR8200A Manual de usuario

Honeywell

Honeywell THP9045 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario