Honeywell XENON 1900 Manual de usuario
Xenon™ 1900
Corded Area-Imaging Scanner
Quick Start Guide
NG2D-QS Rev B
5/11
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Für Deutsch gehe zu www.honeywellaidc.com.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
Перейти на русскоязычный сайт www.honeywellaidc.com.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
查看繁体版请登陆 www.honeywellaidc.com
한글 www.honeywellaidc.com 로이동합니다 .
Note: Refer to your user’s guide for information about cleaning your
device.
For localized language versions of this document, go to
www.honeywellaidc.com.
Getting Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Power Supply Assembly (if included)
Connecting the Scanner
USB:
Keyboard Wedge:
RS232 Serial Port:
RS485:
Reading Techniques
The view finder projects an aiming
beam that should be centered over
the bar code, but it can be
positioned in any direction for a
good read.
Hold the scanner over the bar code,
pull the trigger, and center the
aiming beam on the bar code.
The aiming beam is smaller when
the scanner is closer to the code and larger when it is farther from the
code. Hold the scanner close to smaller bar codes, and farther away
from large bar codes to get a proper read.
If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.
Standard Product Defaults
The following bar code resets all standard product default settings.
Standard Product Defaults
RS485 Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to program
the terminal, then power cycle the cash register.
Note: For additional RS485 interface selections, see the User’s
Guide for your product at our website,
www.honeywellaidc.com.
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan
the numeric bar code(s) from page 2, then the Save bar code to
program the keyboard for your country. As a general rule, the
following characters are not supported by the scanner for countries
other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~.
Country Code Scan Country Code Scan
Belgium 1Italy 5
Denmark 8Norway 9
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Interface
Program Keyboard Country
Note: For a complete list of country codes, see the User’s Guide for
your product at our website, www.honeywellaidc.com.
Trigger
The following bar codes will allow you to use the scanner in Manual
Trigger - Normal Mode (need to press the trigger to read) or
Presentation mode (the scanner is activated when it “sees” a bar
code).
Finland 2Spain 10
France 3Switzerland 6
Germany/Austria 4USA (Default) 0
Great Britain 7
Country Code Scan Country Code Scan
Save
Manual Trigger - Normal
(Default)
Presentation Mode
Streaming Presentation™
When in Streaming Presentation mode, the scanner leaves the scan
illumination on all the time and continuously searches for bar codes.
Suffix
If you want a carriage return after the bar code, scan the Add CR
Suffix bar code. To add a tab after the bar code, scan the Add Tab
Suffix bar code. Otherwise, scan the Remove Suffix bar code to
remove the suffixes.
Add Code ID Prefix to all Symbologies
Scan the following bar code if you wish to add a Code ID prefix to all
symbologies at once.
Streaming Presentation Mode
Add CR Suffix
Remove Suffix
Add Tab Suffix
Add Code ID Prefix To All Symbologies
(Temporary)
Note: For a complete list of Code IDs, see the User’s Guide for your
product at our website, www.honeywellaidc.com.
Function Code Transmit
When this selection is enabled and function codes are contained
within the scanned data, the scanner transmits the function code to
the terminal. Charts of these function codes are provided in your
User’s Guide. When the scanner is in keyboard wedge mode, the
scan code is converted to a key code before it is transmitted.
Enable
(Default)
Disable
Data Format Editor Instructions
The following are abbreviated instructions for entering a data format.
For complete instructions refer to your User’s Guide, available at our
website, www.honeywellaidc.com.
1. Scan the Enter Data Format symbol.
2. Primary/Alternate Format: scan 0for Primary Format
3. Terminal Type: scan 099 for any terminal type
4. Code I.D.: scan 99 for any bar code type
5. Length: scan 9999 for any length bar code.
6. Editor commands: use the Programming Chart that follows.
7. Scan Save to save your entries.
Enter Data Format
Clear All Data Formats
Save
Otros manuales para XENON 1900
6
Tabla de contenidos
Otros manuales de Lector de código de barras de Honeywell
Honeywell
Honeywell Eclipse MS5100 Series Manual de usuario
Honeywell
Honeywell 3800G04-USBKITE Manual de usuario
Honeywell
Honeywell Solaris MS7820 Manual de usuario
Honeywell
Honeywell 7120 Orbit Manual de usuario
Honeywell
Honeywell I-Class Mark II Manual de usuario
Honeywell
Honeywell Orbit MS7120 Manual de usuario
Honeywell
Honeywell CM4680 Manual de usuario
Honeywell
Honeywell Solaris MS7820 Manual de usuario
Honeywell
Honeywell MK3780-71A38 Manual de usuario
Honeywell
Honeywell MX7 Tecton Manual de usuario
Honeywell
Honeywell MX7 Tecton Manual de usuario
Honeywell
Honeywell IT3800 Manual de usuario
Honeywell
Honeywell SF61 Manual de usuario
Honeywell
Honeywell 1900GSR-2 Manual de usuario
Honeywell
Honeywell IS4921 Guía de configuración rápida
Honeywell
Honeywell IS4225 ScanGlove Manual de usuario
Honeywell
Honeywell DCS19W Manual de usuario
Honeywell
Honeywell Horizon MS7600 Manual de usuario
Honeywell
Honeywell VoyagerCG MS9540 Manual
Honeywell
Honeywell Voyager 9520 Manual de usuario
