Honeywell 3820 Manual de usuario

3820, 3820i, 4820, 4820i

Cordless Imaging Systems

Quick Start Guide

CRDLSS-02-QS Rev F

1/12

Aller à www.honeywellaidc.com pour le français.

Vai a www.honeywellaidc.com per l'italiano.

Gehe zu www.honeywellaidc.com für Deutsch.

Ir a www.honeywellaidc.com para español.

日本語 : www.honeywellaidc.com をご覧ください。

如要到中国 www.honeywellaidc.com（简体）。

查看繁体版请登陆 www.honeywellaidc.com

한글 www.honeywellaidc.com 로이동합니다 .

Note: Refer to your user’s guide for information about cleaning your

device.

For localized language versions of this document, go to

www.honeywellaidc.com.

Getting Started

Turn off the computer’s power before connecting the base, then

power up the computer once the base is fully connected. When the

base is connected and powered up, put the imager in the base to

establish a link. The green LED on the base flashes to indicate the

imager’s battery is charging.

USB Connection

Keyboard Wedge Connection

Serial (RS-232) Connection

Reading Techniques

The view finder projects an aiming

beam that should be centered over

the bar code. (The 4820/4820i can

be positioned in any direction for a

good read.)

Hold the imager over the bar code,

pull the trigger, and center the

aiming beam on the bar code.

The aiming beam is smaller when

the imager is closer to the code and larger when it is farther from the

code. Hold the imager close to smaller bar codes, and farther away

from large bar codes to get a proper read.

If the bar code is highly reflective (e.g., laminated), you may need to

tilt the imager at an angle so the bar code can be scanned.

4820/4820i

can read in

any direction

Center

beam over

bar code

Note: If the imager beeps 3 times when scanning a bar code, the link

has not been established. If the imager beeps once, the link

has been established.

Standard Product Defaults

This bar code resets all standard product default settings.

Standard Product Defaults

PC Interface

Scan the bar code that describes the PC or interface you are using.

RS-232

USB Keyboard (PC)

Japan DOS/V

USB Japanese Keyboard

(PC)

Emulate External Keyboard

AT/PS2 Keyboard Wedge

(Default)

Keyboard Country

Scan the Program Keyboard Country bar code below, then scan

the numeric bar code(s) from the back of this sheet, then the Save

bar code to program the keyboard for your country. As a general

rule, the following characters are not supported by the imager for

countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~.

Note: For complete list of country codes, see the User’s Guide for

your product at our website, www.honeywellaidc.com.

Country Code Scan Country Code Scan

Belgium 1Italy 5

Denmark 8Norway 9

Finland 2Spain 10

France 3Switzerland 6

Germany/Austria 4USA (Default) 0

Great Britain 7

Program Keyboard Country

Save

Open Link

Scan the Open Link bar code, then place the imager into the base to

establish a link. Placing a different imager into the base establishes

a new link and the old imager is unlinked.

Override Locked Imager

If you need to replace a broken or lost imager that is linked to a base,

scan the Override Locked Imager bar code with a new imager, and

place that imager in the base. The locked link will be overridden; the

broken or lost imager’s link with the base will be removed, and the

new imager will be linked.

Unlinking the Imager

If the base has an imager linked to it, that imager must be unlinked

before a new imager can be linked. Once the previous imager is

unlinked, it will no longer communicate with the base. Scan the

Unlink Imager bar code to unlink an imager.

Open Link

Override Locked Imager

Unlink Imager

Trigger

The following bar codes will allow you to use the reader in Manual

Trigger mode (need to press the trigger to read) or Presentation

mode (the reader is activated when it “sees” a bar code).

Streaming Presentation™ (4820/4820i)

Note: Streaming presentation mode applies only to units with

advanced illumination. Units with advanced illumination have

a software revision of 31205481-027 or higher.

When in Streaming Presentation mode, the imager leaves the scan

illumination on all the time and continuously searches for bar codes.

Manual Trigger

(Default)

Presentation Mode

Streaming Presentation Mode

Reread Delay

This sets the time period before the imager can read the

same

bar

code a second time. Setting a reread delay protects against

accidental rereads of the same bar code.

Suffix

If you want a carriage return after the bar code, scan the Add CR

Suffix bar code. To add a tab after the bar code, scan the Add Tab

Suffix bar code. Otherwise, scan the Remove Suffix bar code to

remove the suffixes.

Medium Reread Delay

Add CR Suffix

Remove Suffix

Add Tab Suffix

Otros manuales para 3820

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Honeywell

Honeywell

Honeywell 3800gPDF - Hand Held Decoding Linear Imager Manual de usuario

Honeywell

Honeywell 1900GHD Manual de usuario

Honeywell

Honeywell ms2420 Manual de usuario

Honeywell

Honeywell IS4225 ScanGlove Manual de usuario

Honeywell

Honeywell 7820 Solaris Manual de usuario

Honeywell

Honeywell Granit 1280i Manual de usuario

Honeywell

Honeywell Captuvo SL22 Manual de usuario

Honeywell

Honeywell XENON 1900 Manual de usuario

Honeywell

Honeywell Metrologic 3780 Manual de usuario

Honeywell

Honeywell HH1800 Manual de usuario

Honeywell

Honeywell IS4921 Guía de configuración rápida

Honeywell

Honeywell CM4680 Manual de usuario

Honeywell

Honeywell VoyagerGS 9590 Series Manual de usuario

Honeywell

Honeywell Quantum T 3580 Manual de usuario

Honeywell

Honeywell MS7320 InVista Manual de usuario

Honeywell

Honeywell Vuquest 3310g Manual de usuario

Honeywell

Honeywell Vuquest 3310g Manual de usuario

Honeywell

Honeywell Fusion MS3780 Manual de usuario

Honeywell

Honeywell 8680i Series Manual de usuario

Honeywell

Honeywell XENON 1902 Manual de usuario

Honeywell

Honeywell VOYAGER 1202G BF Manual de usuario

Honeywell

Honeywell MS1890 Focus Manual de usuario

Honeywell

Honeywell DCS19W Manual de usuario

Honeywell

Honeywell MK7580-30A38-00-A - MS7580 Genesis - Wired Barcode... Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario