Honeywell Hyperion 1300G Manual de usuario

™

Hyperion 1300g

General Purpose Handheld Linear Scanner

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in speci-

fications and other information contained in this document without prior notice,

and the reader should in all cases consult HII to determine whether any such

changes have been made. The information in this publication does not repre-

sent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the furnish-

ing, performance, or use of this material. HII disclaims all responsibility for the

selection and use of software and/or hardware to achieve intended results.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, repro-

duced, or translated into another language without the prior written consent of

HII.

Web Address: www.honeywellaidc.com

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

For patent information, refer to www.hsmpats.com.

Chapter 1 - Getting Started

About This Manual ...................................................... 1-1

Unpacking the Scanner............................................... 1-1

Connecting with USB .................................................. 1-1

Connecting with Keyboard Wedge.............................. 1-2

Connecting with RS-232 Serial Port............................ 1-3

Connecting with RS485............................................... 1-3

Reading Techniques ................................................... 1-4

Menu Bar Code Security Settings ............................... 1-5

Chapter 2 - Programming the Interface

Introduction ................................................................. 2-1

Programming the Interface - Plug and Play ................ 2-1

Keyboard Wedge................................................... 2-1

Laptop Direct Connect........................................... 2-1

RS232 Serial Port.................................................. 2-2

RS485 ................................................................... 2-2

OPOS Mode .......................................................... 2-3

USB IBM SurePos................................................. 2-4

USB PC or Macintosh Keyboard ........................... 2-5

USB HID POS ....................................................... 2-5

USB Serial Commands ............................................... 2-5

USB Serial Emulation............................................ 2-5

CTS/RTS Emulation .............................................. 2-6

ACK/NAK Mode..................................................... 2-6

Honeywell Bioptic Aux Port Configuration................... 2-6

Datalogic™ Magellan®Bioptic Aux Port Configuration2-7

Wincor Mode A............................................................ 2-7

Keyboard Country Layout ........................................... 2-8

Keyboard Mode Options ........................................... 2-18

ALT Mode............................................................ 2-18

Keyboard Style .................................................... 2-18

Keyboard Modifiers ............................................. 2-19

Table of Contents

RS232 Modifiers ........................................................2-22

RS-232 Baud Rate...............................................2-22

RS-232 Word Length: Data Bits, Stop Bits, and Parity

2-23

RS-232 Handshaking.................................................2-24

RS232 Timeout....................................................2-27

XON/XOFF ..........................................................2-27

ACK/NAK .............................................................2-27

Scanner to Bioptic Communication............................2-28

Scanner-Bioptic Packet Mode .............................2-28

Chapter 3 - Input/Output Settings

Good Read Indicators..................................................3-1

Beeper – Good Read.............................................3-1

Beeper Volume – Good Read................................3-1

Beeper Pitch – Good Read....................................3-2

Beeper Duration – Good Read ..............................3-2

Beeper Pitch – Error ..............................................3-3

LED – Good Read .................................................3-3

Number of Beeps – Good Read ............................3-3

Good Read Delay ........................................................3-4

User-Specified Good Read Delay.......................... 3-4

Trigger Modes..............................................................3-5

Manual/Serial Trigger ............................................3-5

Automatic Trigger ..................................................3-5

Presentation Mode.................................................3-6

Continuous Illumination Mode (Manual Trigger only) .

3-6

Hands Free Time-Out ..................................................3-6

Reread Delay...............................................................3-7

User-Specified Reread Delay ................................3-8

Centering .....................................................................3-8

iii

Output Sequence Overview ...................................... 3-10

To Add an Output Sequence............................... 3-10

Other Programming Selections ........................... 3-10

Output Sequence Editor ...................................... 3-11

Output Sequence Editor ...................................... 3-13

Require Output Sequence................................... 3-13

Multiple Symbols ....................................................... 3-13

No Read .................................................................... 3-14

Video Reverse........................................................... 3-15

Chapter 4 - Data Editing

Prefix/Suffix Overview ................................................. 4-1

To Add a Prefix or Suffix ....................................... 4-2

To Clear One or All Prefixes or Suffixes................ 4-2

To Add a Carriage Return Suffix to All Symbologies4-

Prefix Selections.................................................... 4-3

Suffix Selections.................................................... 4-4

Function Code Transmit ........................................ 4-6

Intercharacter, Interfunction, and Intermessage Delays 4-

Intercharacter Delay .............................................. 4-7

User Specified Intercharacter Delay...................... 4-7

Interfunction Delay ................................................ 4-8

Intermessage Delay .............................................. 4-8

Chapter 5 - Data Formatting

Data Format Editor Introduction .................................. 5-1

To Add a Data Format........................................... 5-1

Other Programming Selections ............................. 5-2

Interface / Terminal ID Table....................................... 5-4

Data Format Editor Commands ...................................5-4

Send Commands ...................................................5-4

Move Commands...................................................5-7

Search Commands ................................................5-8

Miscellaneous Commands...................................5-10

Data Format Editor ..............................................5-14

Data Formatter.....................................................5-14

Chapter 6 - Symbologies

Introduction .................................................................. 6-1

All Symbologies........................................................... 6-2

Codabar Start/Stop Characters ............................ 6-3

Codabar Check Character..................................... 6-4

Codabar Concatenation ........................................ 6-5

Codabar Message Length ..................................... 6-6

Code 39 Start/Stop Characters............................. 6-7

Code 39 Check Character..................................... 6-7

Code 39 Message Length ..................................... 6-8

Code 39 Append ................................................... 6-8

Full ASCII ............................................................ 6-10

Code 39 Code Page............................................ 6-10

Check Digit .......................................................... 6-11

Interleaved 2 of 5 Message Length..................... 6-12

Code 93 Message Length ................................... 6-13

Code 93 Code Page............................................ 6-13

Straight 2 of 5 Industrial Message Length........... 6-15

Straight 2 of 5 IATA Message Length ................. 6-16

Matrix 2 of 5 Message Length ............................. 6-17

Check Digits Required......................................... 6-18

Code 11 Message Length ................................... 6-19

ISBT 128 Concatenation ..................................... 6-19

Code 128 Message Length ................................. 6-20

Code 128 Code Page.......................................... 6-20

Code 128 Function Code Transmit ..................... 6-21

Telepen Output.................................................... 6-22

Telepen Message Length.................................... 6-23

UPC A Check Digit .............................................. 6-24

UPC A Number System....................................... 6-25

UPC A Addenda .................................................. 6-25

UPC A Addenda Required .................................. 6-26

UPC A Addenda Separator ................................. 6-26

UPC E0 and UPC E1 .......................................... 6-28

UPC E0 and UPC E1 Expand ............................. 6-29

UPC E0 and UPC E1 Addenda Required ........... 6-29

UPC E0 and UPC E1 Addenda Separator .......... 6-30

UPC E0 Check Digit ............................................ 6-30

UPC E0 Number System..................................... 6-31

UPC E0 Addenda ................................................6-31

EAN/JAN 13 Check Digit .....................................6-32

EAN/JAN 13 Addenda .........................................6-33

EAN/JAN 13 Addenda Required..........................6-33

EAN/JAN 13 Addenda Separator ........................6-34

ISBN Translate ....................................................6-34

EAN/JAN 8 Check Digit .......................................6-35

EAN/JAN 8 Addenda ...........................................6-36

EAN/JAN 8 Addenda Required............................6-36

EAN/JAN 8 Addenda Separator ..........................6-37

MSI Check Character ..........................................6-37

MSI Message Length...........................................6-38

Plessey Message Length.....................................6-39

GS1 DataBar Expanded Message Length...........6-41

Korea Post Message Length ...............................6-43

Codablock F Message Length .............................6-44

Code 49 Message Length....................................6-45

Chapter 7 - Interface Keys

Keyboard Function Relationships ................................7-1

Supported Interface Keys ............................................7-2

Chapter 8 - Utilities

To Add a Test Code I.D. Prefix to All Symbologies .....8-1

Show Software Revision..............................................8-1

Show Data Format.......................................................8-1

Resetting the Standard Product Defaults ....................8-3

Chapter 9 - Serial Programming Commands

Conventions.................................................................9-1

Menu Command Syntax ..............................................9-1

Query Commands..................................................9-2

Concatenation of Multiple Commands...................9-2

Responses.............................................................9-2

Examples of Query Commands.............................9-3

vii

Trigger Commands ..................................................... 9-4

Resetting the Standard Product Defaults.................... 9-4

Menu Commands........................................................ 9-5

Chapter 10 - Product Specifications

Hyperion 1300g Product Specifications .................... 10-1

Standard Connector Pinouts ..................................... 10-2

Chapter 11 - Maintenance

Repairs...................................................................... 11-1

Maintenance.............................................................. 11-1

Cleaning the Device ............................................ 11-1

Inspecting Cords and Connectors....................... 11-1

Replacing the Interface Cable ............................. 11-2

Troubleshooting ........................................................ 11-2

Chapter 12 - Customer Support

Limited Warranty ....................................................... 12-1

Symbology Charts....................................................... A-1

Linear Symbologies............................................... A-1

Postal Symbologies............................................... A-3

ASCII Conversion Chart (Code Page 1252) ...............A-3

Lower ASCII Reference Table .................................... A-5

ISO 2022/ISO 646 Character Replacements .............. A-9

viii

Otros manuales para Hyperion 1300G

Tabla de contenidos

Otros manuales de Lector de código de barras de Honeywell

Honeywell

Honeywell VoyagerCG MS9540 Manual de usuario

Honeywell

Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Manual de usuario

Honeywell

Honeywell Quantum T 3580 Manual de usuario

Honeywell

Honeywell N431X Manual de usuario

Honeywell

Honeywell 1900GHD Manual de usuario

Honeywell

Honeywell 3800gPDF - Hand Held Decoding Linear Imager Manual de usuario

Honeywell

Honeywell YJ-HF5000 Manual de usuario

Honeywell

Honeywell Voyager 1202G Manual de usuario

Honeywell

Honeywell MS7320 InVista Manual de usuario

Honeywell

Honeywell XENON 1900 Manual de usuario

Honeywell

Honeywell PX4-6IE-CUTR-IG-1 Manual de usuario

Honeywell

Honeywell Xenon 1910 Manual de usuario

Honeywell

Honeywell Voyager 1452g Series Manual de usuario

Honeywell

Honeywell Granit XP 199 i Series Manual de usuario

Honeywell

Honeywell Fusion MS3780 Manual de usuario

Honeywell

Honeywell MK3480-30B104 - IS3480 QuantumE - Wired Desktop Barcode... Manual de usuario

Honeywell

Honeywell ms2420 Manual de usuario

Honeywell

Honeywell 3800G04-USBKITE Manual de usuario

Honeywell

Honeywell CM4680 Manual de usuario

Honeywell

Honeywell MS5145 - 00 Manual de usuario

Honeywell

Honeywell Voyager 9520 Manual de usuario

Honeywell

Honeywell Captuvo SL22 Manual de usuario

Honeywell

Honeywell 8670 Manual de usuario

Honeywell

Honeywell Voyager 1602g Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario