HJC RPHA 71 Manual de usuario



※Please visit www.hjchelmets.com for more information about HJC helmets.

PIM EVO Shell

Advanced Channeling

Ventilation System

Pinlock ready

HJ-40 visor(shield)

Provides 99% UV protection

HJ-V12 Internal sun shield

Removable and

washable interior

Inerchangeable cheek pads

throughout all sizes

Double D-ring

Emergency Kit (Cheek Pads)

Anti-fog sun shield Smart HJC 21B & 50B

Install ready

DOT APPROVED

Specications

1. Outer shell

2. Rear venturi exhausts

3. Impact absorbent liner

4. Comfort liner

5. Rubber edge trim

6. Bluetooth Cover

7. Sun shield lever

8. Chin strap

9. Chin strap snap

10. Double "D" ring

11. Bluetooth UI cover

12. Shield locking system

13. Front chin vent

14. Breath deector

15. Anti-fog lens pins

16. HJ-40 Visor(Shield)

17. HJ-V12 Sun shield

18. Eyeport Gasket

19. Shield Ratchet

20. Top Front Vent

12 11

OPEN

3 4

1. Press the visor(shield) locker, then lift the visor(shield) tab up.

2. Open visor(shield) to the maximum open position.

3. Pull the handle-locker to the open position, then pull out the visor(shield) from ratchet mechanism.

Cheek Pad Removal

1. Ensure that the handle-locker is in the open position.

2. Align and insert the top of the shield guide into the plate-gear guide.

3. With the guides properly aligned, press the lower section of the shield into the plate-gear mechanism.

The locking tab should pop into position, locking the shield into place.

Visor(Shield) Installation

Always check to make sure helmet pads are installed before using the helmet. A helmet with

missing or improperly installed pads may increase your risk of serious injury or death in an accident.

There are 3 snaps holding the cheek pad in place.

1. Gently pry the cheek pad away from the interior, releasing the snaps.

2. Grasp the cheek pad near its center and gently pull it free from the chin strap.

Visor(Shield) Removal

1 2

Visor(shield) locker

Handle-locker

OPEN

1 2

OPEN

Visor(shield) tab

Warning!

5 6

1. Align and fully slide the cheek pad plastic plate between shell and EPS.

2. Clip the cheek pad’s 3 small male snaps to the 3 female snaps xed on the shell interior.

1. Install the front section rst by aligning the plastic shell base and the crown pad plastic sleeve, ensuring

that the center and side holes are properly aligned. Press the crown pad plastic sleeve (center portion)

into the center of the channel which is built into the plasticshell base, working your way outward to each

side.

2. Align and snap the two rear snaps into place.

※Slide tab 'A' from the cheek pad into the holder 'B'.(Repeat same

on opposite side)

Cheek Pad Installation

Crown Pad Removal

Crown Pad Installation

Chin Strap Cover Removal

Chin Strap Cover Installation

1. Grasp the end of the chin strap cover and pull/pry

away from the helmet.

1. Insert the chin strap into the chin strap cover and push the chin strap all the way in.

1a 1b

Position of tap holder

1. Grasp the crown pad fabric as close as possible to its plastic base and pull/pry away from the helmet.

Notice how the crown pad plastic section aligns with the shell plastic sleeve. This will help orient you

with the reinstallation.

2. Repeat same at rear.

1 2

1a 1b

7 8

Warning!

■Try not to operate the sun shield while riding as this may impair your vision and may lead to an

accident.

■DO NOT pull on the sun shield when it is already down. The sun shield may be ejected and this

will increase the risk of serious injury or death in the event of an accident.

■Do not attempt to adjust the sun shield itself with your hands.

Always use the sun shield lever.

■

DO NOT use sun shield at night time. The sun shield is only for day time use.

The sun shield does not

provide eye protection. When you use the sun shield

be sure that the clear visor(shield) is also in closed

position.

Above illustration shows raised sun shield

position.

Above illustration shows lowered sun shield

position.

Sun shield Operation

There are three positions for the sun shield sliding lever.

Stage 3 -

Lowest position

Stage 2 -

Lower position

Stage 1 -

Standard position

Lever

Stopper

Stage 1

Stage 2

Stage 3

번역요청건 -

Sun shield Installation

1. Insert sun shield tab 'A' into 'B' position.(Repeat same on opposite side)

※When installing the sun shield, be sure to have it

slided behind the tap ‘B’ holder.

Sun shield Removal

1. Place the stopper in Stage 3.

2. Push the sun shield lever in the direction of the arrow to lower the sun shield as much as possible.

3. Gently pull one side of the sun shield as arrow indicates (repeat same for other side).

Stopper

Stage 3

Lever

9 10

1. To remove the breath deector, pull in the direction of the arrow.

Breath Deector Removal

1a 1b

1. To attach the Breath Deector, insert into the slot and push it in the direction of the arrow.

Breath Deector Installation

1a 1b

Lower Vent Operation

＊Lower Vents open in two ways, and the amount of intake and exhaust can be adjusted.

1. Press the bottom of the lower vent door once to open the rst stage.

2. The 1st position will allow minimum air ow, while the 2nd position will allow maximum air ow.

OPEN

1 2

OPEN

Chin Curtain Removal

1. Pull the chin curtain away from the helmet as arrow

indicates.

1. Align the center of the chin curtain with the center of the helmet. Push into place as arrows indicate.

(Please assemble in order from 1 to 3.)

※Slide tab 'A' from the cheek pad into the holder 'B'.

Chin Curtain Installation

In an emergency, you may remove the cheek pads as

indicated in the illustration. Pull the red line pocket with

your ngers.

Please use Emergency Kit only in emergency

situation.

Emergency Kit

If you install communication system speakers, please do not use the speaker pocket cover.

How to install speaker pocket cover

HJC Intercom Placement Guide

Mounting the Intercom

Unscrew and remove the base cover at the back of the helmet to begin mounting process

of the intercom. Please refer to the manual of the current intercom you are using for directions

on mounting and unmounting the intercom unit.

Base Cover Detachment

1. Remove the screws from the base cover. (picture1)

2. While lifting the base cover(direction A) detach it by pushing toward direction B. (Picture 2)

Base cover

Bracket

Screw

Mounting the Base Cover

Push the base cover underneath the gasket at the bottom of the helmet until the base cover

and the bracket screw holes match. Using the screw, xate the base cover onto the helmet.

1. Push the Bluetooth UI cover in the direction of the arrow while pressing down on A.

Bluetooth UI Cover Detachment

1. After aligning the hook of the Bluetooth UI cover with the groove of the body, and push and attach.

Mounting the Bluetooth UI Cover

Speaker Pocket

Speaker

Speaker Pocket Cover

Tabla de contenidos

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario