HIK VISION ECI-B12F Manual de usuario
ECI-B12F2 • ECI-B12F4 • ECI-B12F6
Network Bullet Camera
Quick Start Guide
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 2
Manual Illustrations and Features
Graphics (screen shots, product pictures, etc.) in this document are for
illustrative purposes only. Your actual product may differ in appearance.
Your product might not support all features discussed in this document.
Hikvision USA Inc., 18639 Railroad St., City of Industry, CA 91748, USA •
Hikvision Canada, 4848 rue Levy, Saint Laurent, Quebec, Canada, H4R 2P1
Telephone: +1-9 9-895- 4 • Toll Free in USA: +1-866-2 -669 • E-Mail:
sales.usa@hikvision.com • www.hikvision.com
COPYRIGHT ©2 17-2 18 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs
are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its
subsidiaries (hereinafter referred to be “Hikvision”). This user manual
(hereinafter referred to be “the Manual”) cannot be reproduced, changed,
translated, or distributed, partially or wholly, by any means, without the
prior written permission of Hikvision. Unless otherwise stipulated, Hikvision
does not make any warranties, guarantees or representations, express or
implied, regarding to the Manual.
About this Manual
This manual may contain several technical incorrect places or printing errors,
and the content is subject to change without notice. The updates will be
added to the new version of this manual. We will readily improve or update
the products or procedures described in the manual.
Regulatory Information
FCC Information
Please take attention that changes or modification not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC Com liance: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 3
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and, if applicable, the supplied accessories too are
marked with “CE” and comply therefore with the applicable
harmonized European standards listed under the Low Voltage
Directive 2 14/35/EU, the EMC Directive 2 14/3 /EU.
2 12/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2 6/66/EC (battery directive): This product contains a battery
that cannot be disposed of as unsorted municipal waste in the
European Union. See the product documentation for specific
battery information. The battery is marked with this symbol, which
may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Com liance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 4
Safety Instruction
These instructions are intended to ensure that user can use the product
correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the warnings are
neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are
neglected.
Warnings
In the use of the device, you must be in strict compliance with the
electrical safety regulations of the nation and region.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and
the Limited Power Source with 12 VDC according to the IEC6 95 -1
standard. Refer to technical specifications for detailed information.
The output current of the power adapter must be no more than 6A.
Do not connect multiple devices to one power adapter to avoid
over-heating or a fire hazard caused by overload.
Make sure that the plug is firmly connected to the power socket.
Make sure that the device is firmly fixed if wall mounting or ceiling
mounting is adopted.
If smoke, odor or noise rise from the device, turn off the power at once
and unplug the power cord, and then contact the service center.
Never attempt to disassemble the camera by unprofessional personal.
Warnings
Follow these
safeguards to
prevent
serious injury
or death.
Cautions
Follow
these
precautions to
prevent
potential injury
or material
damage.
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 5
Cautions
Do not drop the camera or subject it to physical shock.
Do not place the camera in extremely hot, cold (the operating
temperature shall be -4 ° to 6 ° C), dusty or damp locations, and do not
expose it to high electromagnetic radiation.
Do not touch senor modules with fingers.
If cleaning is necessary, use clean cloth with a bit of ethanol and wipe it
gently.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so when any laser
equipment is in using, make sure that the surface of sensor will not be
exposed to the laser beam.
Do not expose the device to high electromagnetic radiation or extremely
hot, cold, dusty or damp environment.
To avoid heat accumulation, good ventilation is required for the operating
environment.
Keep the camera away from liquid while in use for non-water-proof
device.
While in delivery, the camera shall be packed in its original packing, or
packing of the same texture.
Mark Description
Mark
Description
DC Voltage
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 6
Contents
1 A earance Descri tion ......................................................................... 7
2 Installation ............................................................................................. 7
2.1 Ceiling/Wall Mounting .................................................................... 7
2.2 Ceiling/Wall Mounting with Junction Box ...................................... 9
2.3 Waterproof Jacket Installation...................................................... 12
3 Set the Network Camera over the LAN .................................................. 13
3.1 Wiring ........................................................................................... 13
3.2 Activate the Camera ..................................................................... 13
3.2.1 Activation via Web Browser ............................................... 14
3.2.2 Activation via SADP Software ............................................ 14
3.3 Modify the IP Address .................................................................. 15
3.4 Access via Web Browser ............................................................... 16
3.5 Operate via Hik-Connect App ....................................................... 18
3.5.3 Enable Hik-Connect for Use with Cameras ........................ 18
3.5.4 Enable Hik-Connect Service via SADP Software ................ 18
3.5.5 Enable Hik-Connect via a Web Browser ............................ 19
3.5.6 Add Camera to Hik-Connect .............................................. 2
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 7
1A earance Descri tion
This network bullet camera appearance is shown as the figures below.
Network Bullet Camera Overview
No.
Description
1
Lens
2
Front Cover
3
Back Cover
4
Fix Ring
5
Power Cord
6
Network Cable
NOTE:
For power over Ethernet (PoE), the power is passed along with data on
Ethernet cabling. A switch that supports the PoE function is required.
2Installation
Before You Start:
Make sure the device in the package is in good condition and all the
assembly parts are included.
The standard power supply is 12 VDC, make sure your power supply
matches your camera.
Make sure all related equipment is powered off during the installation.
Check the product specification for the installation environment.
Make sure that the wall is strong enough to withstand four times the
weight of the camera and the bracket.
Make sure that there are no reflective surfaces too close to the camera
lens. The IR light from the camera may reflect back into the lens causing
reflection.
2.1 Ceiling/Wall Mounting
Before You Start
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 8
Both wall mounting and ceiling mounting are suitable for the bullet camera.
Ceiling mounting will be taken as an example in this section. Use these
ceiling mounting steps as a reference for wall mounting.
1. Paste the drill template (supplied) to the desired mounting position on
the ceiling/wall.
2. Drill the screw holes in the ceiling/wall according to the supplied drill
template.
Note:
Drill the cable hole if using the ceiling outlet to route the cable.
The Drill Template
3. Route the cables through the cable hole (optional) or the side opening.
4. Fix the camera on the ceiling/wall with supplied screws.
Mount the Camera to the Ceiling/Wall
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 9
NOTES:
The supplied screw package contains both self-tapping screws and
expansion bolts.
If the ceiling is cement, expansion bolts are required to fix the camera. If
the ceiling is wood, self-tapping screws are required.
5. Connect the corresponding power cord, and network cable.
6. Power on the camera.
7. Set the network configuration (for details, refer to 3 Set the Network
Camera over the LAN and 4 Access via Web Browser) to check if the
image is at an optimum angle. If not, adjust the surveillance angle.
1) Loosen the no.1 adjusting screw to adjust the rotation position [ ° to
36 °].
2) Tighten the no.1 adjusting screw.
3) Loosen the no.2 adjusting screw to adjust the tilting position [-9 ° to
9 °].
4) Tighten the no. 2 adjusting screw.
5) Loosen the no.3 fix ring to adjust the pan position [ ° to 36 °].
6) Tighten the no.3 fix ring.
3-Axis Adjustment
8. (Optional) Install the waterproof jacket. Refer to 2.3 Waterproof Jacket
for details.
2.2 Ceiling/Wall Mounting with Junction Box
Before You Start
Both wall mounting and ceiling mounting are suitable for the bullet
camera. Wall mounting will be taken as an example in this section. Use
these wall mounting steps as a reference for ceiling mounting.
ECI-B12Fx Network Bullet Camera Quick Start Guide
QSG VE ECI-B12Fx 6 118NA 1
You will need to purchase a junction box.
1. Paste the drill template (supplied) to the desired mounting position on
the wall/ceiling.
2. Drill the screw holes and the cable hole (optional) in the wall/ceiling
according to the drill template.
NOTE:
Drill the cable hole if using the ceiling outlet to route the cable.
Drill Template
3. Take apart the junction box, and align the screw holes of the bullet
camera with those on the junction box’ cover.
4. Fix the camera on the junction box’s cover with three PM4 × 1 screws.
Mount Camera onto Junction Box Cover
5. Secure the junction box’s body on the wall with three supplied screws.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cámara de seguridad de HIK VISION
HIK VISION
HIK VISION DS-2DP1636ZIX-D Manual de usuario
HIK VISION
HIK VISION DS-2CD6445G1 Series Manual de usuario
HIK VISION
HIK VISION DS-2CE16COT-IRF Manual de usuario
HIK VISION
HIK VISION DS-2CS54D7T-IRS Manual de usuario
HIK VISION
HIK VISION DS-2CE5AD8T-AVPIT3Z Manual de usuario
HIK VISION
HIK VISION DS-2CE12UF3T-E Manual de usuario
HIK VISION
HIK VISION DS-2CD2532F-I Manual de usuario
HIK VISION
HIK VISION DS-2DF1-614X/604X Manual de usuario
HIK VISION
HIK VISION DS-2AF1-764 Manual de usuario
HIK VISION
HIK VISION DS-2CC1282P(N)-IT3 Manual de usuario
HIK VISION
HIK VISION D8T Series Manual de usuario
HIK VISION
HIK VISION DS-2CD2452F-IW Manual de usuario
HIK VISION
HIK VISION HWI-T241H Manual de usuario
HIK VISION
HIK VISION DS-2DP8A440IXG-LEF/624(F0) Manual de usuario
HIK VISION
HIK VISION HiWatch Series Manual de instrucciones
HIK VISION
HIK VISION DS?2CC5173P(N)?VP(IR)(?H) Manual de usuario
HIK VISION
HIK VISION DS-2CC5197P-VPIR Manual de usuario
HIK VISION
HIK VISION iDS-TCV907-BIR Manual de usuario
HIK VISION
HIK VISION DS-2CC5181P-VPIR Manual de usuario
HIK VISION
HIK VISION DS-2TD2667-15/PY Manual de usuario
