HIK VISION DS-2DP1636ZIX-D Manual de usuario
PanoVu Series Camera
Quick Start Guide
COPYRIGHT © 2019 Hikvision. ALL RIGHTS RESERVED
Quick Start Guide
ALL RIGHTS RESERVED
Any and all information, including, among others, wordings, pictures, graphs
are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or
its subsidiaries (hereinafter referred to be “Hikvision”). This user manual
(hereinafter referred to be “the Manual”) cannot be reproduced, changed,
translated, or distributed, partially or wholly, by any means, without the prior
written permission of Hikvision. Unless otherwise stipulated, Hikvision does
not make any warranties, guarantees or representations, express or implied,
regarding to the Manual.
About this Manual
This Manual is applicable to PanoVu Series PTZ Camera.
The Manual includes instructions for using and managing the product.
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the Manual is
subject to change, without notice, due to rmware updates or other reasons.
Please find the latest version in the company website (http://overseas.
hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and logos
mentioned below are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-
INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO
YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT,
EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE
OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION
SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK
ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modication not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
FCC compliance: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too
are marked with "CE" and comply therefore withthe applicable
harmonized European standards listed under the the EMC
Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the
European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information
see: www.recyclethis.info
2006/66/EC and its amendment 2013/56/EU (battery directive):
This product contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,
return the battery to your supplier or to a designated collection
point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
Safety Instruction
These instructions are intended to ensure that the user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
The device should be used in compliance with local laws, electrical safety
regulations, and re prevention regulations.
Transportation
Keep the device in original or similar packaging while transporting it.
Power Supply
The input voltage should conform to IEC60950-1 standard: SELV (Safety Extra Low
Voltage) and the Limited Power Source. Refer to the appropriate documentation
for detailed information.
The standard power supply is 36 VDC, please make sure your power supply
matches with your camera.
Use the power adapter provided by certificated company. Refer to the product
specication for detailed power requirement.
Use the power adapter that can work normally at an altitude over 5000 meters
above sea level.
DO NOT connect multiple devices to one power adapter, to avoid over-heating or
re hazards caused by overload.
Make sure the plug is properly connected to the power socket.
System Security
The installer and user are responsible for password and security conguration and
its settings.
Battery
Improper use or replacement of the battery may result in explosion hazard.
Replace with the same or equivalent type only. Dispose of used batteries in
conformance with the local codes.
Maintenance
If the product does not work properly, please contact your dealer or the nearest
service center. We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular replacement.
The average lifespan varies, so periodic checking is recommended. Contact your
dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside surfaces of the
product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device lens is not exposed
to the laser beam, or it may burn out.
Do not expose the device to high electromagnetic radiation or dusty environments.
For indoor-only device, place it in a dry and well-ventilated environment.
Do not aim the lens at the sun or any other bright light.
Make sure the running environment meets the requirement of the device. The
operating humidity shall be 90% or less (non- condensing), and the operating
temperature is below:
-40 °C to 70 °C (-40 °F to 158 °F)
Do not place the camera in extremely hot, cold, dusty or damp locations, and do
not expose it to high electromagnetic radiation.
IR Reection Prevention
Dust or grease on the dome cover will cause IR reection. Please do not remove
the dome cover lm until the installation is nished. If there is dust or grease on the
dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.
Make sure that there is no reective surface too close to the camera lens. The IR
light from the camera may reect back into the lens causing reection.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the power,
unplug the power cable, and contact the service center.
Time Synchronization
Set up camera time manually for the first time access if the local time is not
synchronized with that of the network. Visit the camera via Web browse/client
software and go to time settings interface.
Installation
Make sure the device is rmly secured to a vertical wall or a horizontal ceiling with
lean angle of the device less than ± 5°
Be sure that there is enough space to install the camera and accessories.
Make sure that the device in the package is in good condition and all the assembly
parts are included.
Make sure that the wall is strong enough to withstand at least 8 times the weight of
the camera and the mount.
Use the provided gloves when open up the camera cover. Avoid direct contact with
the camera cover, because the acidic sweat of the ngers may erode the surface
coating of the camera cover.
Make sure that the power has been disconnected before you wire, install, or
disassemble the device.
Wrap water-proof tape around connectors and wire connections for outdoor use.
Read this manual before using the product.
The installation part shows the instruction for the whole camera series.
You camera may be different on the cables and other aspects.
Symbols and Marks
Notice
Warning
Forbidden
Correct
Incorrect
Turn to page A and continue.
i. Not necessarily included accessory.
ii. Variable accessory amount.
iii. Skip this step if not required.
MicroSD card
Grounding
Disposal
Purchase separately
1
3
2
3
2
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cámara de seguridad de HIK VISION
HIK VISION
HIK VISION DS-2CD2452F-IW Manual de usuario
HIK VISION
HIK VISION iDS-TCV500-BI Manual de usuario
HIK VISION
HIK VISION DS-2CE56D5T-VFIT3 Manual de usuario
HIK VISION
HIK VISION ECI-B64Z2 Manual de usuario
HIK VISION
HIK VISION PanoVu PT Series Manual de usuario
HIK VISION
HIK VISION DS-2CD886BF-E Manual de usuario
HIK VISION
HIK VISION DS-2CD2683G0-IZS Manual de usuario
HIK VISION
HIK VISION DS-2DF8836IV-AEL Manual de usuario
HIK VISION
HIK VISION DS-2CD4A26FWD-IZSP Manual de usuario
HIK VISION
HIK VISION DS-2CD2T87G2-L Manual de usuario
HIK VISION
HIK VISION iDS-TCV500-B(I)/IM Manual de usuario
HIK VISION
HIK VISION DS-2DE2103 Manual de usuario
HIK VISION
HIK VISION HWI-T621H-Z Manual de usuario
HIK VISION
HIK VISION DS-2CC502PN-IR1 Manual de usuario
HIK VISION
HIK VISION DS-2CV2026G0-IDW Manual de usuario
HIK VISION
HIK VISION DS-2CD6362F-I Manual de usuario
HIK VISION
HIK VISION DS-MH6171I-A Manual de usuario
HIK VISION
HIK VISION UD04828N Manual de usuario
HIK VISION
HIK VISION iDS-TCE507-BR Hoja de instrucciones
HIK VISION
HIK VISION DS-2TD4137-25/W Manual de usuario
