Herd FL33BG Manual de usuario

Installation guide

1-888-543-4373

www.HERD.com

1-888-543-4373

Part No: FL33BG-IG

Rev: A

Date: 20-Sep-16

Important

Herd Bumpers are vehicle "Make & Model" specific. Use of a bumper on a vehicle other than the model it was

designed for will constitute improper use of the product and may void warranty.

Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these

instructions, OE hardware means the truck's original factory hardware.

For further detail of warranty coverage and warranty repair information visit www.HERD.com.

SKU #

Truck Model

FL33BG / FL44BG

Freightliner Cascadia

General Safety

Take time to fully read the instructions before installing the Herd bumper.

At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.

Parts and components of the Herd bumper can be heavy, handle with care to avoid injuries.

Respect power tools and use them as advertized.

For assistance call

1-888-543-4373

www.HERD.com

Thank you for choosing HERD!

HERD North America Inc.

2168 Springfield Road

Box 28, Group 525, RR5

Winnipeg, MB. Canada R2C 2Z2

Parts and tools referenced in this instruction

1-888-543-4373

www.HERD.com

1-888-543-4373

Part No: FL33BG-IG

Rev: A

Date: 20-Sep-16

Parts and hardware included

Tools Required

Tool

Specification

Socket

3/4” or 19 mm

Socket

1/2” or 13 mm

Wrench

3/4” or 19 mm

Wrench

1/2” or 13 mm

Item No

Part No

Description

Qty

BG-GR-01

ASSY-WLD CASCADIA

BG-MTK-01

ASSY-FL33BG MOUNTING KIT

1MPA001

ASSY-WLD STUD BRACKET

NLN0.75-10GR8

NYLON LOCK NUT ¾-10GR8 YZP

FW0.75GR8

FLAT WASHER ¾ GR8 YZP

1TBA001

ASSY-WLD CASCADIA TOW

1TBA002

ASSY-WLD SUBMOUNT

HN0.5-13GR5OS

HEX NUT ½-13 TAPPED OVERSIZE

BW0.5SS18-8

BELLEVILLE WASHER ½ SS18-8

NLN0.3125-18GR8

NYLON LOCK NUT 5/16-18 GR8 YZP

Submount

Receiver bolts

Bumper guard

stud plates

Installation Procedure

Part No: FL33BG-IG

Rev: A

Date: 20-Sep-16

1-888-543-4373

www.HERD.com

1-888-543-4373

1. Assemble submounts by inserting

receiver bolt (Item 6) into

submount (Item 7) and securing

the assembly using the supplied

¾” flat washers and nylon lock

nuts (do not tighten hardware at

this stage).

Figure 1 –Assemble receiver bolt into submounts.

2. Insert bumper guard stud plates

(Item 3) into bumper center

uprights from bottom of bumper.

Using the supplied 5/16”flat

washers and nylon lock nuts

(Item 10) to secure plates in

place (tighten locknut just

enough to engage the nylon,

allowing the plate to move freely

during installation).

Figure 2 –Guard mounting plate installation.

Installation Procedure

Part No: FL33BG-IG

Rev: A

Date: 20-Sep-16

1-888-543-4373

www.HERD.com

1-888-543-4373

3. Insert submount assembly into

factory tow receiver holes as

shown.

Figure 3 –Submount assembly installation.

4. Push on receiver bolt (Item 6) to

compress factory tow receiver

spring housed in casting. Once

spring is depressed, rotate

submount assembly 90 degrees

to the vertical position as shown

ensuring the receiver bolt

engages factory casting. Tighten

¾” nylon lock nuts (Item 4),

ensuring that the submount is

level (vertically) and flush against

factory tow receiver casting face,

then torque hardware to 200 ft-

lbs (271 N·m). Repeat on

opposite side of bumper.

Figure 4 –Submount assembly installation. Narrow Rad version shown.

Installation Procedure

Part No: FL33BG-IG

Rev: A

Date: 20-Sep-16

1-888-543-4373

www.HERD.com

1-888-543-4373

5. Install bumper guard onto

submounts, guiding loose inner

mounting plate aligning them

with holes in submount. From

backside of upright, install ½”

lock washers (Item 9) and ½” hex

nuts (Item 8) as shown. Center

and level the bumper guard and

torque hardware to 86 ft-lbs (115

N·m).

Figure 5 –Bumper guard attached to submounts.

6. Open truck hood to ensure there

is no interference with the hood

and top of bumper guard.

Note:

If bumper guard adjustment is

required, loosen hardware

tighten in step 5, readjust then

tighten all hardware.

Figure 6 –Bumper guard installed (Narrow Rad version shown).

Important

Check mounting points after the first 5000 km and every 3-6 month.

Este manual sirve para los siguientes modelos

Otros manuales de Accesorios para automóviles de Herd

Herd

Herd AeroPLUS C4-02 Guía

Herd

Herd KW01 Manual de usuario

Herd

Herd Aero Manual de usuario

Herd

Herd C4 Series Manual de usuario

Herd

Herd PB11C4-02 Manual de usuario

Herd

Herd Aero Manual de usuario

Herd

Herd SLAM LATCH Guía

Herd

Herd Aero Manual de usuario

Herd

Herd 404006 Manual de usuario

Herd

Herd KW22C4-02 Manual de usuario

Herd

Herd IN27BG Manual de usuario

Herd

Herd Aero Series Manual de usuario

Herd

Herd WS30C4-02 Manual de operación y mantenimiento

Herd

Herd IN24A2 Manual de usuario

Herd

Herd MK15C4-02 Manual de usuario

Herd

Herd Defender Series Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario