Herd Aero Series Manual de usuario
1
Installation guide
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: S007
Rev: A
Date: 11-Oct-16
Important
Herd Bumpers are vehicle "Make & Model" specific. Use of a bumper on a vehicle other than the model it was
designed for will constitute improper use of the product and may void warranty.
Unless otherwise specified, Grade 8 or Class 10.9 hardware is to be used. For the purposes of these
instructions, OE hardware means the truck's original factory hardware.
For further detail of warranty coverage and warranty repair information visit www.HERD.com.
Product
Series
Surface mount
signal light
Aero, Aero LT, Defender FLT,
Defender, Texas, Big Tex, RT,
SRT
General Safety
Take time to fully read the instructions before installing the Herd bumper.
At all times exercise safe work shop practices, wear steel toe boots and safety glasses during installation.
Parts and components of the Herd bumper can be heavy, handle with care to avoid injuries.
Respect power tools and use them as advertized.
For assistance call
1-888-543-4373
www.HERD.com
Thank you for choosing HERD!
HERD North America Inc.
2168 Springfield Road
Box 28, Group 525, RR5
Winnipeg, MB. Canada R2C 2Z2
Parts and tools referenced in this instruction
2
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: S007
Rev: A
Date: 11-Oct-16
Parts and hardware included
Tools Required
Tool
Specification
Socket
9/16” or 14 mm
Wrench
9/16” or 14 mm
Drill
Drill Bit
1/8” and ½”
Item No
Part No
Description
Qty
1
4LMP001
LED Light
2
2
FW0.375GR5
Flat Washer - 3/8” Grade 5
4
3
HSLW0.375
Spring lock washer - 3/8”
4
4
HN0.375-16GR5
Hex Nut –3/8” - 16 Grade 5
4
5
Wires
White –Ground, Red –Turn Signal, Black –
Marker light
NA
1
5
2
3
4
Installation Procedure
3
1-888-543-4373
www.HERD.com
1-888-543-4373
Part No: S007
Rev: A
Date: 11-Oct-16
1. If the Bumper channel contains
holes for the signal light.
Unplug pigtails and feed the
wires (Item 5) through the hole in
the channel. Use 3/8” nuts (Item
4) to mount the light as shown in
Figure 1. Tighten nuts until lock
washer is flattened, do not over
tighten to avoid damage to the
light. Connect the pigtails back in.
Repeat for the other side.
Wiring:
White –Ground
Red –Turn Signal
Black –Marker light
Figure 1
2. No holes in the bumper for the
signal light.
Locate two center punched
marks in the back of the channel
(Figure 2). Drill two ½” holes
(1/8” pilot hole) using marks for
reference. Once holes are drilled
install lights as outlined in Step 1.
Figure 2
4
1
5
Bumper channel
3
2
Center punched
marks
Installation Procedure
4
Part No: S007
Rev: A
Date: 11-Oct-16
1-888-543-4373
www.HERD.com
1-888-543-4373
3. If bumper has cut outs for the
OEM (factory) driving lights.
Find two center punched marks
in the alternative location –
usually at the bottom of the
bumper (Figure 3). Drill two ½”
holes (1/8” pilot hole) using
marks for reference. Once holes
are drilled install lights as
outlined in Step 1.
Figure 3
Center punched
marks
OEM light cutout
Este manual sirve para los siguientes modelos
7
Otros manuales de Accesorios para automóviles de Herd
Herd
Herd IN24A2 Manual de usuario
Herd
Herd FL33BG Manual de usuario
Herd
Herd Aero Manual de usuario
Herd
Herd Aero Manual de usuario
Herd
Herd IN27BG Manual de usuario
Herd
Herd PB11C4-02 Manual de usuario
Herd
Herd KW01 Manual de usuario
Herd
Herd 404006 Manual de usuario
Herd
Herd SLAM LATCH Guía
Herd
Herd MK15C4-02 Manual de usuario
