Heatmiser TouchScreen Series Manual de usuario

1Model: DT-TS / DT-NTS

Model: DT-TS / DT-NTS

2Model: DT-TS / DT-NTS

TouchScreen Series Model: DT-TS / DT-NTS

Table Of Contents

3-4

5-6

7-8

Product Image

Table of Contents

What is a Room Thermostat?

Installation Procedure

LCD Display

Temperature Display

Clean Screen

Locking the Keypad

Temperature Control

14-15

19-22

Frost Protection

Heating ON/OFF

Optional Features Explained

Adjusting the Optional Settings

Optional Settings - Features Table

Re-calibrating the Thermostat

Factory Reset

Wiring Diagrams

43 TouchScreen Series Model: DT-TS / DT-NTS

What is a Room Thermostat?

If your heating system is a boiler with radiators, there will usually be only one room

thermostat to control the whole house. But you can have dierent temperatures

in individual rooms by installing thermostatic radiator valves (TRVs) on individual

radiators.

If you don’t have TRVs, you should choose a temperature that is reasonable for the

whole house. If you do have TRVs, you can choose a slightly higher setting to make

sure that even the coldest room is comfortable, then prevent any overheating in other

rooms by adjusting the TRVs.

Room thermostats need a free ow of air to sense the temperature, so they must not

be covered by curtains or blocked by furniture. Nearby electric res, televisions, wall

or table lamps may also prevent the thermostat from working properly.

A room thermostat simply switches the heating system on and o as necessary.

It works by sensing the air temperature, switching on the heating when the air

temperature falls below the thermostat setting, and switching it o once this set

temperature has been reached.

Setting a room thermostat to a higher temperature will not make the room heat up

any faster. How quickly the room heats up depends on the design & size of the heating

system.

Similarly reducing the temperature setting does not aect how quickly the room cools

down. Setting a room thermostat to a lower temperature will result in the room being

controlled at a lower temperature, and saves energy.

The way to set and use your room thermostat is to nd the lowest temperature settings

that you are comfortable with, and then leave it alone to do its job.

The best way to do this is to set the room thermostat to a low temperature

– say 18°C , and then turn it up by 1°C each day until you are comfortable with the

temperature. You won’t have to adjust the thermostat further. Any adjustment above

this setting will waste energy and cost you more money.

65 TouchScreen Series Model: DT-TS / DT-NTS

1 2

3 4

Installation Procedure

This Touchscreen Series thermostat is designed to be ush mounted and requires a

back box of 35mm (minimum depth) to be sunk into the wall prior to installation.

Step 1

Carefully separate the front half of the thermostat from the back plate by placing a

small at head terminal driver into the slots on the bottom face of the thermostat.

Step 2

Place the thermostat front somewhere safe.

Terminate the thermostat as shown in the diagrams on pages 19-22 of this booklet.

Step 3

Screw the thermostat back plate securely into the back box.

Step 4

Clip the front of the thermostat back onto the thermostat back plate.

Mount the thermostat at eye level.

Read the instructions fully so you get the best from our product.

Don’t

Do not install near to a direct heat source as this will aect functionality.

Do not push hard on the LCD screen as this may cause irreparable damage.

87 TouchScreen Series Model: DT-TS / DT-NTS

1 2 3

1. OFF Key - Single press to enable/disable frost protection or press and hold to

turn o display.

2. Flame Icon - Displayed when the thermostat is calling for heat.

3. Keypad Lock Icon - Displayed when the keypad is locked.

4. Frost Icon - Displayed when the thermostat is in frost protection mode.

5. Room Temp - Indicates the current temperature sensor mode.

6. Set - Displayed when the target temperature is adjusted.

7. Clean Screen - Freezes screen temporarily to enable cleaning.

8. Cancel Key - Used to exit setup/program operations.

9. Setup/Programming Keys - Used to navigate setup options.

10. Up/Down Keys - Increase or decrease values shown on bottom digit group.

11. Current Temp - Indicates the current sensor temperature.

12. Units of Temperature - Degrees Celsius or Fahrenheit.

LCD Display

Room Temperature SET Temperature

Temperature Display

The temperature display information is driven by two dierent inputs; the sensor

measurement and the target temperature you have set.

This is the current room temperature. This is the temperature you are trying to

achieve in your home.

109 TouchScreen Series Model: DT-TS / DT-NTS

Locking the Keypad

The thermostat has a keypad lock facility.

• To activate the lock press the bottom right corner of the display and hold for 10 secs.

• When activated, you will see the Keypad Lock symbol.

• To cancel, press the bottom right corner of the display again for 10 secs.

Clean Screen

Pressing will disable all keys, providing you 15 seconds to wipe the screen

clean before the keys are re-activated.

Keypad Lock Indicator

1211 TouchScreen Series Model: DT-TS / DT-NTS

The keys under the temperature display allow you to adjust the

set temperature.

When you press either of these keys, you will see the temperature and

the word SET appear on screen.

Select the desired temperature and press to conrm and exit.

Temperature Control

Set Temperature

Set Icon

Pressing the key once will place the thermostat in frost protect mode.

In this mode, the thermostat will display the frost icon and will only turn the heating on

should the room temperature drop below the set frost temperature (see page 14).

Should the heating be turned on whilst in frost mode, the ame symbol will be

displayed.

To cancel the frost protect mode, press the key once.

Frost Mode

Frost Protection Mode Enabled

1413 TouchScreen Series Model: DT-TS / DT-NTS

THE FOLLOWING SETTINGS ARE OPTIONAL AND IN MOST CASES

NEED NOT BE ADJUSTED

Feature 01 – Temperature Format: This function allows you to select between °C or °F.

Feature 02 - Switching Dierential: This function allows you to increase the switching

dierential of the thermostat. The default is 1°C which means the thermostat will

switch the heating on 1°C below the set temperature and will turn it o when the set

temperature is achieved. With a 2°C dierential, the heating will switch on 2°C below the

set temperature and will switch o when the set temperature is achieved.

Feature 03 - Frost Protect: You can set whether the thermostat will maintain the frost

temperature when the thermostat display is turned o. As a default, this is enabled.

Feature 04 – Frost Protect Temperature: This is the temperature maintained when the

thermostat is in frost mode. The range is 07-17°C. The default is 12°C and is suitable for

most applications.

Feature 05 – Output Delay: To prevent rapid switching, an output delay can be entered.

This can be set from 00 - 15 minutes. The default is 00 which means there is no delay.

Optional Features Explained

The heating is indicated ON when the ame icon is displayed.

When the ame icon is absent, there is no requirement for heating to achieve the set

temperature but the thermostat remains active.

To turn the thermostat OFF completely, press and hold the OFF key .......................

The display and heating output will be turned o completely.*

To turn the thermostat back ON, press the ON key once ...............................................

Heating On/O

Thermostat completely OFF Thermostat powered ON

*See Feature 3 on page 14

1615 TouchScreen Series Model: DT-TS / DT-NTS

Feature 06 – Communication Address: This setting is used when you have

connected your thermostat to a network system. Each thermostat on the network

must have a unique communication address. This can be set from 01-32.

Feature 07 – Temperature Up/Down Limit: This function allows you to limit the use

of the up and down keys. This limit is also applicable when the thermostat is locked

and so allows you to give others limited control over the heating system.

To adjust the optional settings, follow these steps.

• Press SETUP ..................................................................................................................

• Use the Up/Down keys at the top of the screen to select the feature

number (shown on page 17) and then use the Up/Down keys in the

center to adjust the setting ....................................................................................

• Press DONE to conrm settings and exit ...........................................................

Adjusting the Optional Settings

Feature Number

Setting Value

Optional Features Continued

1817 TouchScreen Series Model: DT-TS / DT-NTS

If you need to re-calibrate the thermostat, follow these steps.

• Press and hold the OFF key to turn the thermostat OFF ........................................

• Press and hold the ON key until the temperature appears on screen ...............

• Use the Up/Down keys to congure the new temperature .........................

• Press DONE to conrm settings .......................................................................................

• Press the ON key once to turn the thermostat back ON .........................................

Re-calibrating the Thermostat

FEATURE

Temperature Format

Switching Dierential

Frost Protect

Frost Protection Temperature

Output Delay

Communications ID No.

Up/Down Temperature Limit

DESCRIPTION

00 = oC

01 = oF

(°C = Default)

0.5o- 3.0oC (1.0oC = Default)

00 = Disabled

01 = Enabled

(01 = Default)

07o- 17oC (12oC = Default)

Enter Value: 00 - 15 Minutes (00 = Default)

Enter number 01-32

00o- 10oC (00oC = Default)

SETTING

Optional Settings - Feature Table

The thermostat has a reset function to restore all settings to their factory defaults.

To perform a factory reset, follow these steps.

• Turn the thermostat OFF by pressing and holding the OFF key.

Press and hold the bottom left corner of the LCD for 10 seconds .......................

• All of the screen icons will appear for 2 seconds and then disappear.

• Press the ON key once to turn the thermostat back ON .........................................

Factory Reset

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Heatmiser

Heatmiser

Heatmiser PRTHW-W Manual de usuario

Heatmiser

Heatmiser SP OpenTherm neoHub Mini OT Manual de usuario

Heatmiser

Heatmiser DT Manual de usuario

Heatmiser

Heatmiser PRT-WTS Manual de usuario

Heatmiser

Heatmiser PRT-E Manual de usuario

Heatmiser

Heatmiser PRT Manual de usuario

Heatmiser

Heatmiser Touch Manual de usuario

Heatmiser

Heatmiser edge Manual de usuario

Heatmiser

Heatmiser SLIMLINE Manual de usuario

Heatmiser

Heatmiser PRT-EW Manual de usuario

Heatmiser

Heatmiser DS1-L Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Heatmiser

Heatmiser neoUltra Manual de usuario

Heatmiser

Heatmiser UH8 Manual de usuario

Heatmiser

Heatmiser TM4-TS Manual de usuario

Heatmiser

Heatmiser JG PRT-E Manual de usuario

Heatmiser

Heatmiser PRT-B Manual de usuario

Heatmiser

Heatmiser DT-W Manual de usuario

Heatmiser

Heatmiser smartstat Manual de usuario

Heatmiser

Heatmiser Wireless Series Manual de usuario

Heatmiser

Heatmiser DS1-EL Manual de usuario

Heatmiser

Heatmiser Slimline-RF Manual de usuario

Heatmiser

Heatmiser neoStat-hw V2 Manual de usuario

Heatmiser

Heatmiser PRT-R2 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Honeywell

Honeywell T6811 Manual de usuario