Heath Zenith Notifi elite Manual de usuario

elite

video doorbell

Owner’s Manual

Thank You for Purchasing Notiﬁ™ Elite Doorbell

Welcome to Notiﬁ by HeathZenith. This manual will help setup the Notiﬁ system. Please read and understand this entire manual

before attempting to assemble, install, or operate the Notiﬁ system. For additional support and videos, go to www.heath-zenith.

com/notiﬁ.

IMPORTANT INFORMATION

• Minimum system requirement for the Notiﬁ app is iOS 9.0 or higher and Android 5.0 or higher.

Many states regulate the use of security cameras and other recording devices. It is the purchaser’s sole

responsibility to ensure compliance with all applicable laws and to provide any legally required notices.

Check local laws regarding the use of any recording devices and cameras prior to installation.

Introduction

Table of Contents

INTRODUCTION.............................2-4

SETUP ...................................5-7

HOW TO USE .............................8-11

CARE AND CLEANING......................... 11

FAQS ..................................12-14

To maintain the compliance with the RF exposure guideline, place the base unit at least 7.875" (20 cm) from nearby persons.

CAUTION

Introduction

Speciﬁcations

Power Requirements:

16 VAC/10 VA Transformer

Video Quality:

Resolution: Hi (Default) = 1280x720 (720p), Med = 640x360, Low = 320x180

Frame Rate: Adjustable up to 25 Fps

Viewing Angle: 160°

Maximum Recording Length: 2 minutes per recording

Operating Temperature: -13 to +120°F (-25°C to +50C)

NOTICE: Install the Notiﬁ Elite doorbell in a covered location; away from direct sunlight, rain, and humidity. Do not allow

salt water or other conductive liquids to come into contact with the doorbell.

Motion Detection Range: Adjustable up to 30 ft. (9.1 m)

Minimum System Requirements for the Notiﬁ App: iOS 9.0 or higher and Android 5.0 or higher, Broadband Internet

Connection with Home Wi-Fi®: Download speed is 3 MB/s and upload speed is 3 MB/s

Subscriptions

Notiﬁ offers two levels of service.

Basic Service (Included):

• Notiﬁcations and photo alerts • Lighted push button

• Custom motion detection zones • 24/7 on demand live viewing

• Programmable muting • 24 Hr cloud storage

Premium Service (Available for an additional monthly or yearly fee):

Premium service includes all Basic service features plus:

• Push button activated video recording • Motion-activated video recording

• 30 day cloud storage

You Will Need

• Existing wired chime

• Password for your home network

• Broadband Internet connection with home Wi-Fi router

• Phillips screwdriver

• Flat-head screwdriver

Introduction

Carton Inventory

Notiﬁ Elite Doorbell

Power Module

Microphone

Camera

Motion Sensor

Speaker

Spade Connectors (Connect

to chime terminals)

Push Button

LED Indicator Ring

Chime Wires (Connect to

existing chime wires)

Window Cling Decal Wire Quick Connect

All activities are

monitored &

recorded by video

camera

Screws (#6 x 3/4"), Wall Anchors, and Double-Sided Tape (for Power Module)

Install the Notifi Elite doorbell in a covered location; away from direct sunlight, rain, and humidity. Do not allow salt

water or other conductive liquids to come into contact with the doorbell.

NOTICE

Setup

Install the Notiﬁ Elite Doorbell

Before connecting the Notifi Elite doorbell to a multi-tune electronic chime (see illustration on bottom of page 6), set the

chime to the desired tune. See chime manual for tune selection instructions.

NOTICE

1. Remove the existing wired push button.

2. Remove the backplate of the Notiﬁ Elite doorbell by pushing in tab on the bottom with a small, ﬂat-head screwdriver.

3. Insert the existing push button wires through the wire hole located just below the terminal screws. Attach the backplate to

the wall using the #6 screws (only use the screws included to ensure proper installation).

IMPORTANT: Be careful not to bend the metal contacts during backplate installation or while connecting the wires to the

backplate.

4. Connect the wires to either screw terminal on the backplate.

5. Slide the top of the Notiﬁ Elite doorbell down onto the backplate and press the bottom of the Elite doorbell against the

backplate until it snaps onto the backplate.

ATTACH BACKPLATE

Remove material in screw holes (if needed)

before mounting with screws.

CONNECT WIRES

Connect wires to screw terminals

REMOVE COVER

Push in tab with a small screwdriver

INSTALL COVER

Hook top of cover onto top of

backplate and rotate down until

cover snaps into place

IMPORTANT: Be

careful not to bend the

metal contacts during

backplate installation

or while connecting the

wires to the backplate.

SetupSetup

Install the Power Module

The Notiﬁ Elite doorbell requires a power module to be installed for each Notiﬁ Elite doorbell connected to your chime.

1. Remove the chime cover from the existing chime.

2. Label the chime wires according to the terminals they are attached to (TRANS, FRONT, REAR).

3. Remove the transformer (TRANS) wire and connect it to one of the wires on the power module using the wire quick connect

(included). Connect the power module spade connector on this wire to the transformer (TRANS) screw terminal.

4. Remove the wire going to the Notiﬁ Elite doorbell (either FRONT or REAR) and connect it to the other wire on the power

module using the wire quick connect (included). Connect the power module spade connector on this wire to the screw

terminal the wire was previously attached to. NOTE: Once the Notiﬁ app is connected to the Notiﬁ Elite doorbell (see Step 4,

page 7), go to > Advanced Settings > Chime Selection and select the type of chime the Notiﬁ Elite is connected to (see

illustrations below).

5. Using the double-sided tape (included), attach the power module to the chime. If the power module prevents the cover from

being installed, install the cover and then attach the power module to the exterior of the chime cover.

6. Replace the chime cover.

IMPORTANT: Do not allow the power module or wires to touch the tone bars (mechanical chime) or cover the speaker

(electronic chime) as this may affect the sound of the chime when activated.

CONNECTING TO AN ELECTRONIC CHIME CONNECTING TO A MECHANICAL CHIME

FRONT

REAR

TRANS

Setup

Download the Notiﬁ App

iOS Devices

Go to the App StoreSM and search for the “Notiﬁ Connected Products” app and download.

Android Devices

Go to the Google Play™ store and search for the “Notiﬁ Connected Products” app and download.

Setup the Notiﬁ App and Camera

IMPORTANT: Your home password will be required during this process.

1. Allow the Notiﬁ Elite doorbell 1 minute to fully boot-up.

2. On your mobile device, go to Settings > Wi-Fi. Select the “Notiﬁ Elite XXXX” (“XXXX” represents the unique MAC address

of each Notiﬁ Elite doorbell) from the available Wi-Fi networks.

3. Once connected, open the Notiﬁ app. The app will detect your new Notiﬁ system.

4. Select “YES” to start the setup and the app will guide you through the remaining steps.

NOTE: Your username will be your email. Your password must be a minimum of 8 characters or a maximum of 12 characters.

Alpha numeric and/or special characters may be used. IMPORTANT: The password must include at least 1 number and 1 letter.

How to Use

Systems Tab

The Systems tab is the “home screen” for all of your Notiﬁ systems. From here you can access the following choices:

• Notiﬁ systems – The Systems tab lists all Notiﬁ systems available. Tap on the desired Notiﬁ system to view a live camera

view.

• mute unmute – Selecting the “Mute” button will immediately mute your chime. Muting the chime from this location will

override any scheduled mute settings. Select “Unmute” to return to the scheduled mute settings.

• – Selecting the “Gear” icon next to a Notiﬁ system will allow you to adjust different settings for that Notiﬁ system.

• Add Notiﬁ System – At the bottom of the list of Notiﬁ systems is this selection. Tap on “Add Notiﬁ System” to learn how

to add additional systems to your Notiﬁ app.

• Logout – Once logged out, you will be asked to log back in if you receive a notiﬁcation from a Notiﬁ system on this device.

• Need help? – Selecting this link will take you to the Notiﬁ FAQ website where you will have access to additional help features

as well as contacting HeathZenith technical service department.

• i– Tap on this icon to access additional information about the Notiﬁ app.

Live-Streaming Video

The Notiﬁ system provides a live-stream of video from the Notiﬁ camera to your mobile device that is viewable at any time.

To view the live-stream video, tap the name of the camera you wish to view. To return to the main app screen, tap the or

Back in the top left corner.

From the live-streaming video screen, the microphone input on the Notiﬁ camera will broadcast to the speaker

on your mobile device, providing you with a constant stream of audio from the location of the Notiﬁ camera.

The microphone is muted by default. To unmute the microphone, tap the speaker icon at the bottom of the

screen. To mute the audio again, tap the speaker icon again.

Push to Talk From the live-streaming video screen, you may also talk to the person at your door by pressing and holding

the Push to Talk button. While you are holding the button, your voice is heard through the speaker on the Notiﬁ

Elite doorbell. Release the button when you ﬁnish speaking to hear the person at the door.

To record video from the live-stream screen, tap the video camera icon to start recording video. Then

tap the same video camera icon to stop recording video. The video will be saved to the mobile device you are

currently using. The maximum length of recorded video is 2 minutes.

To save a still image from the live-stream screen, tap the camera icon . The image will be saved to the

mobile device you are currently using.

NOTE: The icons above will turn RED when activated.

Events

An event is created when the push button is pressed. Two pictures from the Notiﬁ camera will be stored to the cloud for 24

hours. With the Premium Service, when the push button is pressed two pictures and a video from the Notiﬁ camera will be

stored to the cloud for 30 days. Also with Premium Service, two pictures and a video event will be stored for 30 days with every

motion trigger.

To view an event, tap the Events tab. Then tap the name of the Notiﬁ system you would like to view events for. Then select

the event category, Doorbell Motion . The events will be listed chronologically. Tap the event you wish to view.

To download an event to your device, swipe left across the event you wish to download and tap the download icon . Verify

you want to download the event and it will be downloaded to your device.

To delete an event, swipe left across the event you wish to delete. Then tap the trashcan icon .

Notiﬁcations

When the push button is pressed, two images will be stored and you will receive a push or email notiﬁcation.

When you receive a push notiﬁcation, you will be able to tap on the notiﬁcation and the app will open to the live feed view.

Push Button LED Halo Ring

The Notiﬁ Elite Doorbell has a LED halo ring around the push button. This LED halo offers additional information as to the status

of the Notiﬁ Elite system. See the FAQ section on page 13 for additional details.

Notiﬁ Software Updates

Whenever a ﬁrmware update is available for a Notiﬁ product, the “gear” icon next to the applicable product on the

“Systems” screen will change to a download icon . This icon will remain on the screen until the ﬁrmware update has

been completed. NOTE: A reminder pop-up screen will also appear each time you log into the Notiﬁ app reminding you that a

ﬁrmware update is available. This pop-up screen will continue to appear until the ﬁrmware has been updated.

Camera Settings

> Feature Settings > Camera

The camera settings allow you to adjust the motion detection sensitivity, create motion detection zones, and adjust the video

quality settings.

Motion Detection: Adjust the Notiﬁ camera’s sensitivity to motion in its ﬁeld of view.

Motion Detection Zones: Adjust the Notiﬁ camera’s detection area to include or exclude zones within the camera’s view.

Auto Adjust: Disabling this setting allows manual adjustments of the video’s quality settings. TIP: For best performance leave

the Auto Adjust ON.

IMPORTANT: With any setting changes make sure you press the Save button Save in the upper right corner if you want to keep

your changes.

How to Use

Notiﬁcation Settings

> Feature Settings > Notiﬁcations

The notiﬁcations settings screen allows you to enable, schedule, and disable push notiﬁcations and email notiﬁcations.

IMPORTANT: With any setting changes make sure you press the Save button Save in the upper right corner if you want to keep

your changes.

Mute Settings

> Feature Settings > Mute Settings

The Notiﬁ system allows you to mute your chime from within the Notiﬁ app. The mute settings allow you to schedule times

during the day when the chime should be muted.

Default (2 Hour): Mutes the chime for a period of two hours from the time this selection is made. This selection may be turned

OFF at any time.

Weekday: Allows for a speciﬁc time during the day to be selected to mute the chime. The scheduled time is applied to all

selected days. This selection may be turned OFF at any time.

Weekend: Allows for quick scheduling of weekend only times when the chime is to be muted. This selection may be turned OFF

at any time.

IMPORTANT: The chime can be muted quickly from the Systems selection tab by selecting “Mute” under the selected Notiﬁ

system. Any scheduled mute settings will be overridden while the chime is muted from the Systems tab. Select “Unmute” to

return to the scheduled mute settings.

IMPORTANT: With any setting changes make sure you press the Save button Save in the upper right corner if you want to keep

your changes.

Multiple Users

> Advanced Settings > Manage Multiple Users

The Notiﬁ system allows you to control multiple “guest” users within your account. These users will receive notiﬁcations when

the Notiﬁ Elite push button is pressed and will be able to access the camera’s live feed view. The “guest” users will not be able

to access any of the Notiﬁ settings you have setup.

To add a “guest” user to your multiple user list, tap the “Add Viewers” button and type their email address in the “To:” ﬁeld, then

tap the “Send” button. The “guest” user will receive an email inviting them to view your system. They will need to download the

Notiﬁ app and create their own account before they are able to access your Notiﬁ system.

You can turn off their access to your Notiﬁ system at any time by tapping their username in the list. You can turn it back on by

tapping their username again.

To delete a “guest” user from the list, swipe the username to the left and tap the trashcan icon ( ).

How to Use

Tabla de contenidos

Otros manuales de Accesorios de Heath Zenith

Heath Zenith

Heath Zenith DUAL BRITE SL-5597 Manual de usuario

Heath Zenith

Heath Zenith SL-7464-03 Manual de usuario

Heath Zenith

Heath Zenith Lighted Wireless Push Button Accessory Manual de usuario

Heath Zenith

Heath Zenith DESA 6270 Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime 598-1172-04 Manual de usuario

Heath Zenith

Heath Zenith HZ-1802-BK-A Manual de usuario

Heath Zenith

Heath Zenith Replacement Motion Sensor SH-5407 Manual de usuario

Heath Zenith

Heath Zenith Wireless Chime 6153/62/71/72 Manual de usuario

Heath Zenith

Heath Zenith Motion Sensor Entryway Light SL-5610/15 Manual de usuario

Heath Zenith

Heath Zenith Wireless Christmas Chime 598-1127-03 Manual de usuario

Heath Zenith

Heath Zenith 598-1215-01 Manual de usuario

Heath Zenith

Heath Zenith 121AC Manual de usuario

Heath Zenith

Heath Zenith Wireless Strobe Chime 6144 Manual de usuario

Heath Zenith

Heath Zenith InTune MP3 Door Chime Manual de usuario

Heath Zenith

Heath Zenith 7797 Manual de usuario

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-06 Manual de usuario

Heath Zenith

Heath Zenith 7750 Manual de usuario

Heath Zenith

Heath Zenith Decorative Wireless Chime 598-1000-07 Manual de usuario

Heath Zenith

Heath Zenith 5867 Manual de servicio

Heath Zenith

Heath Zenith SL-6153 Manual de usuario

Heath Zenith

Heath Zenith Hardwired Electronic Chime 598-1313-00 Manual de usuario

Heath Zenith

Heath Zenith Wireless Push Button Accessory 598-1105-05 Manual de usuario

Heath Zenith

Heath Zenith Motion Sensing 3-Way Wall Switch 6107 Manual de usuario

Heath Zenith

Heath Zenith 3106978 (AC-6196) Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario