Hand Held Products SCANTEAM 2070 Manual de usuario

™

Quick Start

Cordless Scanning System

SCANTEAM® 2070 Base

IMAGETEAM™ 3870/75 Linear Imager

SCANTEAM® 5770 Laser

Disclaimer

Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make

changes in specifications and other information contained in this document

without prior notice, and the reader should in all cases consult Hand Held

Products to determine whether any such changes have been made. The

information in this publication does not represent a commitment on the part of

Hand Held Products.

Hand Held Products shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages

resulting from the furnishing, performance, or use of this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced,

or translated into another language without the prior written consent of Hand

Held Products.

Web Address: www.handheld.com

The CE mark on the product indicates that the system has been tested

to and conforms with the provisions noted within the 89/336/EEC

Electromagnetic Compatibility Directive and the 73/23/EEC Low

Voltage Directive.

For further information please contact:

Hand Held Products, Inc.

Nijverheidsweg 9

5627 BT Eindhoven

The Netherlands

Hand Held Products shall not be liable for use of our product with equipment (i.e.,

power supplies, personal computers, etc.) that is not CE marked and does not

comply with the Low Voltage Directive

C.S.A. Statement

This product must be used with a certified Class 2 Power

supply or be powered by a certified SELV (Safety Extra

Low Voltage) output.

Patents

Please refer to the product packaging for patent information.

Chapter 1 - Cordless Quick Start Guide

Introduction .....................................................................................1

About the Charge Pack....................................................................2

Associating the Cordless Scanner to a Base....................................5

IMAGETEAM 3875 Scanner Features ..........................................6

Product Service and Repair.............................................................7

Technical Assistance .......................................................................8

Limited Warranty ............................................................................9

Statement of Agency Compliance ................................................11

Table of Contents

Cordless Scanning System Quick Start 1

Cordless Quick Start Guide

Introduction

The cordless scanning system consists of the SCANTEAM 2070 Base unit and

at least one IMAGETEAM 3870 Cordless Linear Imager, IMAGETEAM 3875

Cordless Linear Imager, or SCANTEAM 5770 Cordless Laser Scanner. Up to

nine IT3870, IT3875, or ST5770 scanners may be associated with one base.

Each cordless scanner has a removable, rechargeable charge pack and

provides real time decoding within 100 feet (30 m) radius of the base unit

depending on the environment.

The IT3875 is intended to serve cordless applications that require enhanced

user/host interaction. The addition of the 16-key keypad and 97 x 32 pixel

graphic (16 character by 4 lines of text) LCD backlit display enables the user to

enter data and view confirmation of receipt of data. The IT3875 linear imagers

ship with two installed factory scripts and a product demo. These scripts keep

track of scan history or part number and quantity.

Two PC tools also are available to help generate custom applications: IQ App

Loader™ and IQ App Designer™. IQ App Loader is used to compile and load

custom script applications created with a text editor. IQ App Designer, an

optional PC software tool, automates the creation of scripts and the task of

loading a user script application to the system. Using IQ App Designer you may

build custom script applications with minimal programming experience.

The cordless system is an economical, durable solution for a wide variety of

portable data collection applications. The cordless system features:

• a tough, ergonomic thermoplastic housing for comfort and durability.

• an advanced two-way spread-spectrum radio

• recognition and decoding of the most popular, industry-standard bar code

symbologies, including PDF417.

• coverage of up to 31,416 square feet (2,919 square meters) around the base.

• a wide range of interfaces that are compatible with many POS, keyboard

wedge, wands and laser emulation, RS-232 terminals, and legacy decoders.

• visible and audible feedback for confirmation of a successful decode.

• rechargeable charge packs designed to operate through a whole work day.

This Quick Start Guide contains information about charging your cordless

scanner’s charge pack and associating the scanner to the base. For more

detailed information on how to set up, operate, and program the cordless system,

see the Cordless System Manual.

2 Cordless Scanning System Quick Start

This guide contains the following information:

• Charge pack and charging Information

• Associating the cordless scanner to a base

• Customer support information

• Limited warranty and warranty durations

About the Charge Pack

(CLESS/NIMH/S)

Power is supplied to the cordless scanner by a

rechargeable charge pack that snaps onto the

bottom of the scanner. Each scanner is shipped

with a charge pack.* (See the charge pack

specifications in the Cordless System Manual for

storage information.)

*Order backup or replacement charge pack(s) from

your distributor.

North American Charging Information

The charge pack is designed to plug into any two-

prong North American AC power outlet for direct

charging. You need no additional equipment, and you can recharge the pack

virtually anywhere.

Worldwide Charging Information

Since the charge pack is rated for both 120/240 V, 50/60Hz applications, it may

be charged worldwide. Inexpensive snap-on adapters and custom 2-bay and 6-

bay charge strips are available to accommodate a wide variety of electrical

outlets internationally.

Charge Pack Recommendations

• Charge packs are shipped uncharged and need to be conditioned for full

capacity and longer life.

• To maintain the maximum charge capacity, charge packs should be allowed

to fully discharge prior to charging. It is recommended that you establish a

process where a charge pack is used until it is fully discharged and fully

charged before its next use.

• Avoid using the charge pack in extreme temperatures.

• Do not disassemble the charge pack. There are no user-serviceable parts in

the charge pack.

• Avoid extended overcharging; do not leave the charge pack charging for more

than two weeks.

• Periodically, about every 6 months, repeat the charge pack conditioning.

Cordless Scanning System Quick Start 3

Proper Disposal of the Charge Pack

When the charge pack has reached the end of its useful life, the

charge pack should be disposed of by a qualified recycler or

hazardous materials handler. Do not incinerate the charge pack

or dispose of the charge pack with general waste materials.

Contact Hand Held Products (see page 7) for recycling or

disposal information.

Charging Your Charge Pack

(CLESS/NIMH/S)

Charge the charge pack by following the steps below:

1. Detach the charge pack from the bottom of the scanner.

2. Fully charge the charge pack. Plug the

charge pack directly into any common 120

V AC outlet in North America. If outside

North America, use the custom charge strip

or adaptor.

3. The LED on the bottom of the charge pack

blinks red temporarily as part of the charge

initialization sequence. After initialization,

the LED remains solid red while the charge

pack is charging. The LED shows green

when the charge pack is fully charged and

ready to use.

Note:

Recharge Time: 6 hours at any voltage at

20°C (68°F.)

4. After the charge pack is fully charged, attach

it to the cordless scanner by pressing the pack firmly (align the prongs on

the pack with the mating receptacles) in the base of the scanner until the

release buttons click, holding the pack firmly in place. (

When you attach a

charged charge pack to the cordless scanner, you will hear a single beep

5. If you have not set up your Cordless System, refer to “Setting Up and

Connecting the Cordless System” section in the System Manual for

instructions.

When the charge pack needs recharging, the yellow LED on top of the scanner

pulses in short, continuous blinks when the trigger is pulled. If the LED stops

flashing when the temperature lowers or you do not use the charge pack for

some time, you still need to charge the charge pack.

Press Release Buttons

(2 Places)

4 Cordless Scanning System Quick Start

Conditioning the Charge Pack

• Charge packs are shipped uncharged and need to be conditioned for full

capacity and longer life.

• Charge the charge pack for 12 hours for the first two times to fully condition

the pack. (Fully discharge in between each initial charge.)

• Fully discharge the charge pack on a periodic basis by leaving the charge

pack attached to the scanner until the scanner no longer operates, about 24

hours. (Make sure all idle modes are disabled for this procedure -- see

Charge Pack Conservation Mode description in the System Manual.)

Discharging the Charge Pack

A full discharge should take less than 10 hours. Full discharge is indicated when

the trigger is pulled and held for at least 10 seconds and the reader does not

illuminate the aiming line or the status LED. Circuitry in the reader prevents an

over-discharge.

IMAGETEAM 3870/SCANTEAM 5770

The charge packs naturally discharge through normal use of the reader.

Alternately, they may be discharged without user interaction by following these

steps:

1. Disassociate the reader from the base unit by scanning the Remove Scan-

ner/Disassociate bar code (found below).

2. Scan the Battery Discharge Mode bar code (found below) to temporarily

disable the scanner’s power-saving features. The scanner does not

operate normally when in this mode. Do not scan a bar code or the

scanner will exit the Battery Discharge Mode.

3. To resume normal operation, detach and replace the charge pack, then

associate with the base unit by scanning the bar code affixed to the base.

Remove Scanner/Disassociate

Battery Discharge Mode

Cordless Scanning System Quick Start 5

IMAGETEAM 3875

You may automatically discharge the IT3875 charge pack by scanning the

following bar code. The scanner remains operational during the discharge;

however the status LED flashes like a “heartbeat.”

Associating the Cordless Scanner to a Base

Important: Make sure the cordless scanner’s charge pack has been fully

charged. See page 3 for charging instructions.

Using the cordless scanner, scan the Association Bar Code (the bar code label

on the top of the base) to link that scanner to the base.

Two quick beeps followed by clicking, then a single beep indicates a “good”

association. The scanner is in communication with the base. If the scanner

clicks for 30 seconds and signals an error (triple beep), it has not associated with

the base.

Note:

If the charge pack is removed from the scanner and replaced after

association, the scanner automatically reassociates to the base if the

base has power. In this case, the scanner beeps when a charged charge

pack is installed, then beeps a second time after full association, typically

five to ten seconds later.

Note:

A scanner always defaults to work group 0 after scanning a base I.D. bar

code.

Sample codes have been included in the back of this Quick Start Guide. Scan a

bar code to make sure that your scanner is working correctly after you have

charged the charge pack and associated the scanner with a base.

IT3875 Charge Pack Discharge

6 Cordless Scanning System Quick Start

IMAGETEAM 3875 Scanner Features

The IMAGETEAM 3875 includes a keypad and display. In addition to having all

of the functionality of the other cordless scanners offered by Hand Held Products,

the IT3875 allows you to key in data and run scripts that are shipped with the

scanner. Two PC tools also are available to help generate custom applications:

IQ App Loader™ or IQ App Designer™. (IT3875XXX-X2-1 and ST2070-5 only)

You may use IQ App Designer to build custom applications with minimal

programming experience.

One of the factory installed scripts shows the history of the past ten scans on the

display. After you scan a bar code and the information is successfully

communicated to the base, the bar code information appears on the top of the

display. Data from the most recent scan appears at the top of the display while

older data moves down one line at a time. The arrow keys may be used to scroll

up and down through the scan history. Once a line is selected, it is highlighted.

You may also run a script that allows you to enter a part number and quantity.

The part number and quantity prompts can be displayed in six languages.

You may enter alphanumeric characters. The most recently scanned message is

stored in its entirety, up to 2710 characters. Older messages are truncated after

63 characters.

The arrow keys can be used to control vertical line scrolling. Use the Function

(FN) key with the up and down arrows to control horizontal character scrolling. If

the selected line is too wide to fit on the display, an arrow appears at the edge of

the display indicating additional characters. To scroll horizontally toward the end

of the line, press FN and then the UP arrow. To scroll horizontally toward the

beginning of the line, press FN and then the DOWN arrow. (Press and release

FN, and then press the arrow key. Pressing and holding the arrow key causes

horizontal scrolling to repeat.)

You may also program up to eleven macro strings to save a sequence of keypad

strokes. In addition you can control the contrast of the display, turn the backlight

on and off, display indicators of the strength of the battery and the radio contact

with the base, change the font size used when running script applications, and

display the System Setup menu. The System Setup menu lets you run factory

scripts, determine to which work group a scanner is associated, display the

scanner ID, and determine scanner software revision information.

Otros manuales para SCANTEAM 2070

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Hand Held Products

Hand Held Products

Hand Held Products 4X00 Guía de inicio rápido

Hand Held Products

Hand Held Products IK8560 Manual de usuario

Hand Held Products

Hand Held Products Valueteam 3060 Manual de usuario

Hand Held Products

Hand Held Products 4600g Manual de usuario

Hand Held Products

Hand Held Products Quick Check PC600 Manual de usuario

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series Manual de usuario

Hand Held Products

Hand Held Products 4600g Manual de usuario

Hand Held Products

Hand Held Products 2020 Manual de usuario

Hand Held Products

Hand Held Products Quick Check PC600 Manual de usuario

Hand Held Products

Hand Held Products HANDHELD 3800G Manual de usuario

Hand Held Products

Hand Held Products Quick Check QCOLV-SV100 Manual de usuario

Hand Held Products

Hand Held Products 4230 Manual de usuario

Hand Held Products

Hand Held Products 2020/5620 Guía del usuario

Hand Held Products

Hand Held Products Quick Check Bar Code Verifiers 800 Manual de usuario

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series Manual de usuario

Hand Held Products

Hand Held Products 3800PDF Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 3800i Instrucciones de instalación y funcionamiento

Hand Held Products

Hand Held Products 4800p Manual de usuario

Hand Held Products

Hand Held Products 3800ESD Manual de usuario

Hand Held Products

Hand Held Products HandHeld 3800 Linear Series Manual de usuario

Hand Held Products

Hand Held Products IMAGETEAM 4410 Manual de usuario

Hand Held Products

Hand Held Products 4600g Manual de usuario

Hand Held Products

Hand Held Products 4820 Manual de usuario

Hand Held Products

Hand Held Products 2020 Guía del usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario