H3C WA4330-ACN Manual de usuario

H3C WA4330-ACN Access Point

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version:6W101-20170414

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Preface

The H3C WA4330-ACN Access Points Installation Guide guides you through the installation of your AP.

It covers product overview, preparing for installation, installing the AP, and LEDs and ports.

This preface includes the following topics about the documentation:

•Audience.

•Conventions.

•Obtaining documentation.

•Technical support

•Documentation feedback.

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the WA4330-ACN

APs.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Descri

tion

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic

text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars, from

which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n> The argument or keyword and argument combination before the ampersand (&) sign can

be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Descri

tion

Boldface Window names, button names, field names, and menu items are in Boldface. For

example, the New User window opens; click OK.

> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols

Convention Descri

tion

WARNING An alert that calls attention to important information that if not understood or followed can

result in personal injury.

CAUTION An alert that calls attention to important information that if not understood or followed can

result in data loss, data corruption, or damage to hardware or software.

IMPORTANT An alert that calls attention to essential information.

NOTE An alert that contains additional or supplementary information.

TIP An alert that provides helpful information.

Network topology icons

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports

Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access controller

engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.



Represents a security product, such as a firewall, UTM, multiservice security gateway, or

load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL VPN,

IPS, or ACG module.

Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots, and

other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website

at http://www.h3c.com.hk.

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

servic[email protected]

http://www.h3c.com.hk

Documentation feedback

You can email your comments about product documentation to inf[email protected].

We appreciate your comments.



Contents

Product overview·························································································································································· 1

Preparing for installation ············································································································································· 2

Safety recommendations ··················································································································································2

Temperature and humidity requirements ························································································································2

Accessories provided with the AP ···································································································································2

Installation tools and equipment······································································································································3

Installing the AP···························································································································································· 4

Check before installation··················································································································································4

Determining the installation position·······························································································································4

Mounting the AP on a wall······································································································································5

Installing the AP on a ceiling ··································································································································8

Connecting the AP to the power supply ······················································································································ 10

Check before power-on ········································································································································ 10

Connecting PoE+ power supply ·························································································································· 10

Connecting local power supply ··························································································································· 11

Check after power-on············································································································································ 11

Connecting the AP to the network································································································································ 12

Verifying network connection for the fit AP ········································································································ 12

Appendix LEDs and ports ··········································································································································13

LEDs ················································································································································································· 13

Ports ················································································································································································· 13

Index ···········································································································································································15

Product overview

An H3C WA4330-ACN AP can act as a fit AP to cooperate with wireless switches or access controllers

to provide wireless access for WLAN users. The network settings are configured on the wireless switches

or access controllers.

Figure 1 Deployment of the WA4330-ACN on hotspots

Table 1 H3C WA4330-ACN specifications

Item S

ecification

Protocol IEEE 802.11a/b/g/n/ac

Radio interfaces Three

Built-in antennas

•2.4 G antenna: gain 4 dBi

•5 G antenna: gain 5 dBi

Power consumption 5 to 18 W

Dimensions (H × W × D) 54 × 220 × 220 mm (2.13 × 8.66 × 8.66 in)

Weight 0.6 kg (1.32 lb)

WA4330-ACN Switch

Switch

Auditorium

Restaurant or

tea house

Hall or

information desk

Parking lot

WA4330-ACN

Core equipment room

Radius

Server

NMS

Switch

Preparing for installation

Safety recommendations

ARNING!

Only qualified personnel can install and remove the AP and its accessories. You must read all safety

instructions supplied with the AP before installation and operation.

To avoid possible bodily injury and equipment damage, read the following safety recommendations

before installing the AP. Note that the recommendations do not cover every possible hazardous

condition.

•Take adequate safety measures to avoid injury and AP damage.

•Place the AP in a dry and flat location and take anti-slip measures.

•Keep the AP clean and dust-free.

•Do not place the AP in a moist area and avoid liquid surrounding the AP.

•Keep the AP and installation tools away from walkways.

Temperature and humidity requirements

Item S

ecification

Operating temperature (indoor) –10°C to +55°C (14°F to 131°F)

Storage temperature –40°C to +70°C (–40°F to +158°F)

Operating humidity (noncondensing) 5% to 95%

Accessories provided with the AP

Mounting kit (AP bracket, mounting bracket

inner part, and mounting bracket outer part,

from left to right)

M4 × 30 pan head screw, washer, and nut

Wall anchor kit

MAC address label

M4 × 10 pan head screw

Installation tools and equipment

When installing the AP, you may need the following tools. Prepare these tools and equipment yourself.

Needle-nose pliers Wire-stripping pliers Diagonal pliers Marker

Percussion drill with

matching drills Rubber hammer Phillips screwdriver

Installing the AP

Figure 2 Installation flowchart

Check before installation

Before installing an AP, perform the following tasks:

•Connect the AP to the power supply and the network. Examine the LEDs to verify that the AP can

operate correctly. For more information about AP LEDs, see “Appendix LEDs and ports.”

•Verify that cabling on the installation site has been completed.

•To ensure the PoE+ performance, H3C recommends that you use GE interfaces for PoE+ power

supply.

•Record the AP MAC address and serial number marked on the rear of the AP for future use.

Determining the installation position

You can mount the AP to a wall or ceiling. Determine the installation position by observing the following

principles:

•Few obstacles such as wall and ceiling exist between AP and clients.

•The AP is far away from electronic devices (such as microwave oven) that may generate radio

frequency (RF) noise.

Start

Determine the installation

position

Wall-mounting the AP

End

Mount the mounting bracket to

the wall

Install the AP

Connect the AP to the power supply

Connect the AP to the network

Mount the mounting bracket to

the ceiling

Ceiling-mounting the AP

Check before installation

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de H3C

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario