GW Instek GSP-9300B Manual de usuario

Spectrum Analyzer

GSP-9300B

USER MANUAL

ISO-9001 CERTIFIED MANUFACTURER

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS .................................................. 3

GETTING STARTED.......................................................... 8

GSP-9300B Introduction ........................ 9

Accessories.......................................... 12

Appearance .......................................... 14

First Use Instructions .......................... 26

BASIC OPERATION ........................................................ 38

Frequency Settings ............................... 41

Span Settings....................................... 45

Amplitude Settings .............................. 48

Autoset ................................................ 63

Bandwidth/Average Settings ................ 65

Sweep .................................................. 72

Trace .................................................... 80

Trigger ................................................. 88

Marker ................................................. 93

Display............................................... 109

System Settings ................................. 118

Preset ................................................ 122

ADVANCED OPERATION ...............................................124

Measurement..................................... 126

Limit Line Testing .............................. 184

Sequence ........................................... 191

Tracking Generator ............................ 196

Power Meter ...................................... 200

FILE..............................................................................206

File Overview ..................................... 206

GSP-9300B User Manual

REMOTE CONTROL ......................................................222

Interface Configuration ...................... 223

FAQ..............................................................................237

APPENDIX ....................................................................238

Replace the Clock Battery ................... 238

Glossary of Acronyms ........................ 239

GSP-9300B Default Settings ............... 241

Menu Tree .......................................... 243

GSP-9300B Specifications .................. 277

GSP-9300B Dimensions ..................... 285

Declaration of Conformity .................. 286

INDEX ..........................................................................287

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to ensure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the instrument or to

other properties.

DANGER High Voltage

Attention Refer to the Manual

Earth (ground) Terminal

Frame or Chassis Terminal

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

GSP-9300B User Manual

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the instrument.

Avoid severe impact or rough handling that leads

to damaging the instrument.

Do not discharge static electricity to the

instrument.

Use only mating connectors, not bare wires, for

the terminals.

Ensure signals to the RF input do not exceed

+30dBm.

Ensure reverse power to the TG output terminal

does not exceed +30dBm.

Do not supply any input signals to the TG output.

Do not block the cooling fan opening.

Do not disassemble the instrument unless you are

qualified.

(Measurement categories) EN 61010-1:2010 specifies the

measurement categories and their requirements as follows. The

instrument falls under category II.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Measurement category I is for measurements performed on

circuits not directly connected to Mains.

Power Supply

WARNING

AC Input voltage range: 100V~240V

Frequency: 50/60Hz

To avoid electrical shock connect the protective

grounding conductor of the AC power cord to an

earth ground.

SAFETY INSTRUCTIONS

Battery

CAUTION

Rating: 11.1V, 6 cell Li-ion battery

Turn off the power and remove the power cord

before installing or removing the battery.

Cleaning

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 5°C to 45°C

Humidity: <90%

(Pollution Degree) EN 61010-1:2010 specifies the pollution degrees

and their requirements as follows. The instrument falls under

degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution occurs.

Occasionally, however, a temporary conductivity caused by

condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment is

normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature nor

humidity is controlled.

Storage

environment

Location: Indoor

Temperature: -20°C to 70°C

Humidity: <90%

GSP-9300B User Manual

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

SAFETY INSTRUCTIONS

Power cord for the United Kingdom

When using the instrument in the United Kingdom, make sure the

power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed

as follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

GSP-9300B User Manual

GETTING STARTED

This chapter provides a brief overview of the

GSP-9300B, the package contents, instructions for

first time use and an introduction to the front

panel, rear panel and GUI.

GSP-9300B Introduction ................................................... 9

Main Features.................................................................................................................9

Accessories.....................................................................12

Otros manuales para GSP-9300B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de GW Instek

GW Instek

GW Instek GSP-730 Manual de usuario

GW Instek

GW Instek GSP-9300 Manual de usuario

GW Instek

GW Instek GPT-10000 Series Manual de usuario

GW Instek

GW Instek GOM-802GP Manual de usuario

GW Instek

GW Instek LCR-8230 Manual de usuario

GW Instek

GW Instek LCR-8101G Manual de usuario

GW Instek

GW Instek GSP-818 Series Manual del propietario

GW Instek

GW Instek GFG-8215A Manual de usuario

GW Instek

GW Instek PEL-3000 Series Manual de usuario

GW Instek

GW Instek GSP-830TG Manual de usuario

GW Instek

GW Instek GSP-930 Manual del propietario

GW Instek

GW Instek GCM-407 Manual de usuario

GW Instek

GW Instek GOM-804 Manual de usuario

GW Instek

GW Instek LCR-800 Series Manual de usuario

GW Instek

GW Instek GPM-001 Manual de usuario

GW Instek

GW Instek AFG-3000 Series Manual de usuario

GW Instek

GW Instek GSP-730 Manual de usuario

GW Instek

GW Instek GPM-8310 Manual de usuario

GW Instek

GW Instek LCR-8230 Manual de uso y cuidado

GW Instek

GW Instek GOM-804 Guía de inicio rápido

GW Instek

GW Instek GOM-802 Manual de usuario

GW Instek

GW Instek GSP-818-TG Manual de usuario

GW Instek

GW Instek GSP-8000 Series Manual de usuario

GW Instek

GW Instek LCR-6300 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario