GW Instek GPM-8310 Manual de usuario

Digital Power Meter

GPM-8310

USER MANUAL

Rev. A

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

TABLE OF CONTENTS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 5

GETTING STARTED........................................................ 10

Characteristics ..........................................11

Appearance ...............................................16

Set Up.......................................................25

BASIC SETTING ............................................................. 28

Setting up measurement range .................29

Setting up measurement status ................33

Setting up System status ..........................72

MEASUREMENT AND OTHER FUNCTIONS .................... 81

Measurement function ..............................82

Other functions ........................................88

Integration measurement function............91

Graph measurement function .................103

DIGITAL I/O / DA4 .......................................................121

Digital I/O / DA4 Overview .....................122

External Remote Control .........................124

DA4 Output Function ..............................125

User / 4094 Mode ...................................130

REMOTE CONTROL ......................................................136

Configure Remote Control Interface ........137

Configure EOL Character ........................144

Return to Local Control ...........................144

COMMAND OVERVIEW ................................................145

Command Syntax ....................................145

GPM-8310 User Manual

Command List ........................................149

APPENDIX ....................................................................228

Specifications .........................................229

Status system .........................................239

Dimensions ............................................243

Declaration of Conformity .......................244

Power measurement ...............................245

Introduction to IEC-62301.......................247

EUP Directive Lot6 specifications ...........248

Connection Guide ...................................249

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to ensure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the GPM-8310

or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

GPM-8310 User Manual

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

SAFETY INSTRUCTIONS

Safety Guidelines

General Guideline

CAUTION

Make sure that the voltage input level does not

exceed AC600V.

Make sure the current input level does not

exceed 20A.

Do not place any heavy object on the

instrument.

Avoid severe impact or rough handling that can

lead to damaging the instrument.

Do not discharge static electricity to the

instrument.

Use only mating connectors, not bare wires, for

the terminals.

Do not block or obstruct the cooling fan vent

opening.

Do not perform measurement at the source of a

low-voltage installation or at building

installations (Note below).

Do not disassemble the instrument unless you

are qualified as service personnel.

Make sure that the COM terminal to earth is

limited to 600Vpk.

Remove all test leads before disconnecting the

mains power cord from the socket.

If the equipment is used in a manner not

specified by the manufacturer, the protection

provided by the equipment may be impaired.

The device should be placed in a place where

the plug connected to it can be removed easily.

GPM-8310 User Manual

(Note) EN 61010-1:2010 specifies the measurement categories and

their requirements as follows. The GPM-8310 falls under category II

600V.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Power Supply

WARNING

AC Input voltage: 100-240 VAC 50/60Hz

The power supply voltage should not fluctuate

more than 10%.

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

If grounding practice is not well implemented, a

certain amounts of noises will be generated

when connecting to GPM-001, the handy

measurement accessory for GPM-8310.

Cleaning the

Instrument

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Temperature: 0°C to 40°C

Humidity: < 30°C: < 80%RH(non-condensing);

30°C~40°C:<70%RH(non-condensing);

>40°C: <50%RH (non-condensing)

Altitude: <2000m

Overvoltage category: OVC II

SAFETY INSTRUCTIONS

(Note) EN 61010-1:2010 specifies the pollution degrees and their

requirements as follows. The GPM-8310 falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of

dielectric strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Temperature: -40°C to 70°C

Humidity: <90%RH(non-condensing)

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

GPM-8310 User Manual

GETTING STARTED

This chapter describes the GPM-8310 in a nutshell,

including accessories, package contents, its main

features and front / rear panel introduction.

Characteristics ................................................................11

Accessories .............................................................................................. 14

Package Contents .................................................................................... 15

Appearance.....................................................................16

Front Panel ..............................................................................................16

Main Display Overview ...........................................................................19

Rear Panel................................................................................................ 22

Set Up ............................................................................25

Tilting the Stand ...................................................................................... 25

Power Up .................................................................................................26

Connect the wires to the GPM-8310....................................................... 27

Otros manuales para GPM-8310

Tabla de contenidos

Otros manuales de Instrumento de medición de GW Instek

GW Instek

GW Instek GSP-930 Manual del propietario

GW Instek

GW Instek GSP-818 Series Manual de usuario

GW Instek

GW Instek GDM-834X Series Manual de usuario

GW Instek

GW Instek GCP-500 Manual de usuario

GW Instek

GW Instek GSP-830 Manual de usuario

GW Instek

GW Instek GDM-8342 Manual de usuario

GW Instek

GW Instek GCM-407 Manual de usuario

GW Instek

GW Instek GSP-9300 Manual de usuario

GW Instek

GW Instek GSP-830 Manual de usuario

GW Instek

GW Instek GRF-1300 Manual de usuario

GW Instek

GW Instek GPT-10000 Series Manual de usuario

GW Instek

GW Instek GOM-802 Manual de usuario

GW Instek

GW Instek GOM-802 Manual de usuario

GW Instek

GW Instek GPM-8213 Manual de usuario

GW Instek

GW Instek GOM-802 Manual de usuario

GW Instek

GW Instek LCR-8230 Manual de uso y cuidado

GW Instek

GW Instek GSP-730 Manual de usuario

GW Instek

GW Instek LCR-8101 Manual de usuario

GW Instek

GW Instek GFC-8010H Manual de usuario

GW Instek

GW Instek GOM-804 Manual de usuario

GW Instek

GW Instek LCR Series Manual de usuario

GW Instek

GW Instek GPM-8320 Manual de usuario

GW Instek

GW Instek GPM-001 Manual de usuario

GW Instek

GW Instek PEL-5000G Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario