Goldmund SR150 Manual de usuario

USER MANUAL

GOLDMUND SR150 2-CHANNEL

Universal Power Amplifier

INTRODUCTION

The GOLDMUND SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER

Goldmund was founded in 1978 and has ever since been dedicated to the accurate reproduction of sound

and image.

At Goldmund, we strive to lead in the creation, development and manufacture of the industry’s most

advanced technologies, including audio and video systems, home - networking and music distribution.

The guiding principle at Goldmund is to produce a precise sound with the least possible loss of quality

through the different stages. Goldmund will never adopt a technology before it is sufficiently developed to

satisfy the high quality standards we set. This is why Goldmund has often rejected mainstream technologies

and developed its own.

Congratulations.

Thank you for purchasing the Goldmund SR150 2-CHANNEL Universal Power Amplifier.

You have acquired the best multi-usage Power Amplifier ever made for professional and domestic uses.

Please take some time to read this manual.

No connection or manipulation must be

done before reading those instructions.

Damage to the amplifier may result if the

following instructions are not consciously

understood and applied.

WARNING

SR150 2-CHANNEL Universal Power Amplifier

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER

1UNPACKING p 4

2CHOICE OF AMPLIFIER LOCATION AND COOLING p 4

3LINE VOLTAGE ADJUSTMENT p 5

4CONNECTIONS p 5

5AMPLIFIER CONTROLS p 6

6SOUND QUALITY OPTIMIZATION p 7

Warm-up sonic effect.

Speaker polarity.

Mains line phase inversion.

7SAFETY AND PRECAUTIONS p 8

Protection against DC.

Protection against short-circuits.

8MAINTENANCE p 9

9TECHNICAL DATA p9-10

Power

Frequency response

Analog input sensitivity

Group delay

Distortion

Speed

Noise

D/A Converter

Operating temperature

Power supply

Size and weight

Warranty

CONTENTS

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER

UNPACKING

You will find in the GOLDMUND SR150 box:

❑The amplifier

❑The power cord

❑This manual and the warranty card

❑Accessories and spare fuses

Please keep the packaging in case you need to transport the amplifier at a later date

or if you have to send it for maintenance.

WARNING

IF YOU NEED TO RETURN THE SR150 TO THE FACTORY OR TO YOUR LOCAL

REPRESENTATIVE FOR A WARRANTY REPAIR, PLEASE NOTE THAT IT MUST BE

REPACKED IN THE ORIGINAL PACKAGING.

THIS PACKAGING HAS BEEN DESIGNED SPECIFICALLY TO PROTECT YOUR

SR150 IN TRANSIT. USE OF ALTERNATIVE PACKAGING IS LIKELY TO RESULT IN

DAMAGE, INVALIDATING WARRANTY COVER.

CHOICE OF AMPLIFIER LOCATION AND COOLING

The GOLDMUND SR150 amplifier, as all the high quality amplifiers may generate a large

amount of heat if driven at high power.

It is mandatory to allow a proper cooling of the heat sink. Avoid any location which is not

properly ventilated and avoid putting other equipment on top of the amplifier.

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER |P 4

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER |P 5

LINE VOLTAGE ADJUSTMENT

An AC line voltage selection is possible inside the chassis. Please ask your dealer for

assistance if the line voltage provided is not appropriate.

ATTENTION

On the 220V position, the GOLDMUND SR150 amplifier will function properly for AC voltages

between 200V and 245V.

On the 110V position, the AC line must deliver between 95V and 125V. If your AC line is

usually out of these tolerances, please consult your GOLDMUND dealer.

Please check the value of the mains line fuse. This fuse is located in the power cord

receptacle. The lid can be removed with a small screwdriver when the cord is removed.

Use a 5A slow-blow fuse for 220V and a 8A slow-blow fuse for 110V.

CONNECTIONS

Check if volume control is down to zero on the preamplifier.

If you are using analog inputs, connect the interconnects between the preamp/processor

and each of the power amps inputs.

If you are using a Goldmund Universal Preamplifier, connect a lineal digital cable between

one of the preamp outputs and the amplifier digital input. Then change the amp switch back

to digital input.

Connect the speaker cables to the red and black terminals accessible at the back of the

amplifiers.

You may notice that the ground of the input and the black speaker terminal are of the same

polarity. The amplifier is non-inverting in phase.

Then, connect the power cords to the back of the amplifier and plug it in the nearest wall

plug. Use a 3 lugs grounded plug, for safety reasons. Toget the best sound of the amplifier,

avoid any multiple plug or extension cord.

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER |P 6

AMPLIFIER CONTROLS

On the front plate of the GOLDMUND SR150 amplifier you will find only one switch:

The POWER key, used to power the amp on and one power Led.

When turned ON the 2 channels are immediately connected and the front panel POWER Led

lights up. If you use the digital input, the lock of the digital input will indicate this by changing

the Led from green to yellow.

The amp may be powered off by turning off the POWER switch at any time. The Led will fade

very slowly,indicating discharge of the filter capacitors. The speakers will be disconnected

after a few seconds.

It is absolutely normal that a slight sound is heard from the speakers when the amplifiers

are turned ON or OFF. The SR150 is self-protected and the sound heard is corresponding to

the charging and discharging of the capacitors.

On the back panel, there is a 5 Switch set which allows adjusting the D/A Phase and

Gain for the digital input.

Each Switch has 2 positions : ON (high) and OFF (low)

Phase adjustment:

Switch 1 (rightmost) ON: 180 OFF: 0

Left Gain - 6dB: Switch 2: ON Switch 3: ON

0dB: Switch 2: OFF Switch 3: ON

+6dB: Switch 2: ON Switch 3: OFF

+12dB: Switch 2: OFF Switch 3: OFF

Right Gain - 6dB: Switch 4: ON Switch 5: ON

0dB: Switch 4: OFF Switch 5: ON

+6dB: Switch 4: ON Switch 5: OFF

+12dB: Switch 4: OFF Switch 5: OFF

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER |P 7

6SOUND QUALITY OPTIMIZATION

❑Warm-up sonic effect

If the power amplifier has not been powered on for a few days, the optimum sound quality

is reached after 15minutes. This delay has been optimized to be minimal and the sonic

quality when just powered on is much higher than other quality power amplifiers.

❑Speaker polarity

Even if you have an absolute phase inverter on your preamplifier (Mimesis 22M), and even

if you have carefully selected the proper line phase (see in next paragraph), there is a

possibility to again increase the sonic quality of your speakers by reverting the polarity of

each speaker cable at amp termination. But since the line phase and the speaker polarity

interfere to each other, you have to experiment carefully with all the combinations before

picking the right one.

If your preamplifier has an absolute phase inverter,this will interfere too. If it has not, don't

forget the result will depend on the source, as most records and CDs have been recorded

without care for the absolute phase. Be patient…

❑Mains line phase inversion

The sonic quality of your GOLDMUNDSR150can be greatly improved if the mains AC line is

properly connected. Try to invert the AC plugs of both your amplifiers, using special adapters.

Werecommend that you try this carefully. You must do it in combination with the speaker

polarity and/or with absolute phase switching to be sure of the best result.

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER |P 8

ATTENTION

The GOLDMUND SR150 is an extremely high speed amplifier.

Any bad ground connection can generate high frequency oscillation which is

dangerous for tweeters.

It is also generally dangerous to run analog input cable and speaker cables in parallel for a

long distance. If these cables are not of high quality or badly shielded, an “Antenna-Effect”

can generate dangerous high-frequency oscillations.

❑Protection against DC

The GOLDMUND SR150 is a DC-coupled amplifier. Without protection and if it is associated

with a badly designed or defective analog preamplifier (often true for tube preamps and

some 5 channel processors), the speakers could easily be damaged by the amplified DC.

The SR150 protects itself from such an accident by a feedback DC control that limits the DC

amplified by the circuit.

This protection circuit is totally transparent and has no sonic effect.

❑Protection against short-circuits

If one output is short-circuited by accident the amplifier self-limits its output so the current

doesn’t become too high.

However, such accidents should be limited over time to avoid excessive heat build-up

occurring. In extreme cases, such mishandling could destroy the amplifier,which is not

covered by the warranty.

There is no risk to leave the speaker terminals unconnected when the amps are on.

SAFETY AND PRECAUTIONS

User manual - SR150 2-CHANNEL UNIVERSAL POWER AMPLIFIER |P 9

8MAINTENANCE

The GOLDMUND SR150 amplifier usually requires no maintenance.

To clean your SR150 use a very soft, clean, damp cloth to avoid scratching the surface.

Dampen with water or a mild detergent solution. Avoid abrasive or harsh cleansers (eg.

products containing sodium carbonate). Always turn the power off before cleaning your

amplifier.

TECHNICAL DATA

POWER

• Nominal power before clipping: 2x200 W RMS (2 - 8 Ohms). 150 W RMS (1 - 16 Ohms).

•Maximum power : > 400 W RMS (3 Ohms).

• Maximum voltage : 55 V peak. - Maximum current : > 15 A peak.

These values are for both driven channels.

FREQUENCY RESPONSE

These figures are valid for the circuit alone, at any level between 0 and nominal power.

• +/- 0.1 dB, 10Hz - 1 MHz.

• +/- 1 dB, 6 Hz - 1.2 MHz.

• +/- 3 dB, 3 Hz - 1.4 MHz.

ANALOGUE INPUT SENSITIVITY

•Nominal level : 0.75 V.

• Input impedance : 50 kOhms.

GROUP DELAY

Propagation delay < 100 ns stable with frequency from DC to 200 kHz.

Tabla de contenidos

Otros manuales de Amplificador de Goldmund

Goldmund

Goldmund Metis 5 Manual de usuario

Goldmund

Goldmund TELOS 352 Manual de usuario

Goldmund

Goldmund TELOS 2500 Manual de usuario

Goldmund

Goldmund SR8 Manual de usuario

Goldmund

Goldmund TELOS 590 NextGen Manual de usuario

Goldmund

Goldmund TELOS 400 Manual de usuario

Goldmund

Goldmund MIMESIS 16 Manual de usuario

Goldmund

Goldmund GOLDCUBE Manual de usuario

Goldmund

Goldmund METIS ONE Manual de usuario

Goldmund

Goldmund TELOS 390.5 Manual de usuario

Goldmund

Goldmund MIMESIS 22 HISTORY Manual de usuario

Goldmund

Goldmund TELOS 250 Manual de usuario

Goldmund

Goldmund Metis 5 Manual de usuario

Goldmund

Goldmund Amplifiers Manual de usuario

Goldmund

Goldmund THA2 Manual de usuario

Goldmund

Goldmund MIMESIS 28 Manual de usuario

Goldmund

Goldmund MIMESIS 27.8 Manual de usuario

Goldmund

Goldmund MIMESIS 24 Manual de usuario

Goldmund

Goldmund SRI2 Manual de usuario

Goldmund

Goldmund MIMESIS 30 Manual de usuario

Goldmund

Goldmund TELOS 153 Manual de usuario

Goldmund

Goldmund SR2.3 Manual de usuario

Goldmund

Goldmund PH7.3 Manual de usuario

Goldmund

Goldmund TELOS 280 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario