Goldmund MIMESIS 22 Manual de usuario

GOLDMUND MIMESIS 22

ANALOGUE PREAMPLIFIER

USER MANUAL

GOLDMUND MIMESIS 22

ANALOGUE PREAMPLIFIER

USER MANUAL

Warning !

This high quality analogue preamplifier possesses new technical features like ultra-

high bandwidth, digital output and computer linking which are becoming necessary

for an accurate transcription of the today’s best analogue messages in complete

systems with video, computer and audio associated components.

Only a careful use can provide all the satisfaction you are expecting.

All handling must be performed according to the following instructions to avoid the

preamplifier deterioration.

Nevertheless, if the instructions are perfectly carried out, you will notice that the use

of the Goldmund Mimesis 22 is quite simple and convenient.

Important : Please do not connect any wire or move any part before reading the

following instructions.

1. PRELIMINARIES

Please read very carefully the following instructions. This high-precision preamplifier

will provide the best analog signal possible thanks to its unique circuitry.

For exacting technicians, musicians, and all amateurs who demand the very best in

recording transcription, we strongly recommend the use of a top quality D/A

converter to decode the today’s high definition digital signals.

For a perfect Analogue and Digital source system, Goldmund recommends to link the

Mimesis 22 with the Goldmund Mimesis 20 top D/A converter.

The connections between the analogue sources and the preamplifier are also critical.

Ultra low reflection cables are absolutely mandatory. In all typical cases Goldmund

recommends using the special Goldmund Interconnect cables.

Note :

The Goldmund Mimesis 22 is available on option with a Digital output to be linked

with the Mimesis 20. With this option, the Mimesis 22 may record an analogue

source to a digital tape recorder, CD recordable or DVD recordable unit. If you have

this option built in your Mimesis 22, please refer to its separate instructions delivered

with the option to find how to use it.

2 - UNPACKING

You will find in the Goldmund Mimesis 22 box :

- The preamplifier

- The power cord

- This manual

Please keep the packaging in case you need to transport the preamplifier at a later

date or if you have to send it for maintenance.

3 - CHOICE OF THE PREAMPLIFIER LOCATION

The Goldmund Mimesis 22 preamplifier generates a significant amount of heat.

It is necessary to allow a proper cooling of the heat sinks. Avoid any location which is

not properly ventilated and avoid to put on top any equipment sensitive to

temperature.

The MIMESIS 22 uses four adjustable conical feet.

These are used to insure proper vibration transmission to the preamplifier support in

order to evacuate all detrimental vibrations inside the unit, following the famous

Goldmund "Mechanical Grounding" principle.

Depending on the flatness of the surface where the preamplifier will be located, you

will have to adjust slightly one or more of these feet.

The two left feet being evacuating the transformer vibration, it is better to act (if

possible) on the right feet and to leave the left feet fully screwed in.

4 - LINE VOLTAGE ADJUSTMENT

A voltage selector is provided on the back plate of the preamplifier. Adjust it with a

screwdriver if the line voltage provided is not appropriate.

ATTENTION : On the 220V position, the Goldmund Mimesis 22 preamplifier will

function properly for main line voltage in between 200V and 240V. On the 110V

position, the main line must deliver between 105 and 125V. If your main line is

usually out of these tolerances, please consult your Goldmund dealer.

Please check the value of the main line fuse. This fuse is located on the power cord

receptacle. The lid can be removed with a small screwdriver when the cord is

removed.

Use a 1A slow-blow fuse for 220V and 110V.

5 - CONNECTIONS

Connect the power cord to the back of the preamplifier and plug it into the nearest

wall plug. Use only a 3 lugs grounded plug, for safety and noise reasons. To get the

best sound of the preamplifier, avoid any multiple plugs or an extension cord.

Connect the interconnects between the preamp analog outputs and the power amp.

You will plug the cables to the RCA female sockets noted analog outputs.

Connect the interconnects from the source devices to the line inputs number 1 to 7.

Connect the tape machines to any inputs and to the Tape output RCA plugs.

Note 1 :

If you have purchased the special Balanced output option, you can also connect the

XLR marked analog output to the balanced input of a power amplifier. However, you

have to know this mode of connection is not providing you with the ultimate sonic

quality that a Mimesis 22 is built for providing.

Note 2 :

Do not use the input marked “Direct” if you are not using a linked configuration with a

Mimesis 20.

If you are equipped with the special software modules which allow the connection of

several units together, use the DB9 terminated cable provided with this option to

connect the Mimesis 22 to these units and follow the instructions delivered with the

software.

In that case only, use only the input marked “Direct” to connect the analog output of

the Mimesis 20 to the Mimesis 22 analog input module.

Note 3 :

If you purchased the Digital output option for the Mimesis 22, the digital output

module is activated. Without the option, this modu

On the back panel of the Goldmund Mimesis 22 preamplifier the POWER switch is

used to power on the preamplifier. In regular use, this switch is left ON and the

circuits of the preamplifier are activated or disactivated using the standby ON/OFF.

When the POWER switch is switched ON, the preamp will become operative only

after few seconds of warm up, to insure proper stabilization of all the circuitry and

avoid any unwanted noises. After this delay, the output of the preamplifier is

connected to the power amplifier.

The preamp can be powered off by switching the POWER switch to the OFF position.

A special safety circuit switches the preamp to muting, to avoid any disturbance to

reach the power amplifier and the speakers, even if the preamplifier is disconnected

from the AC plug by accident.

However, to optimize the sound quality of the preamplifier and insure the best

reliability, Goldmund recommends that the unit is left powered ON continuously and

is only disactivated by the Standby function.

- MUTING

This switch turns off the output of the preamplifier, without disconnecting the power

supply. It can be used to turn temporarily the volume down without touching the

volume control.

- VOLUME

Each of the left and right level adjustment knob is acting on its separated channel.

However, in order to make the use easier, when only one potentiometer is turned by

hand, the second one is turning of the same dB quantity, insuring a perfect

maintenance of the balance much more precise than with usual stereo potentiometer.

- BALANCE

By pressing the balance key, the electronic lock of the two potentiometers is

disengaged. One potentiometer can be turned without effect on the second one by

pressing the

- INPUT SELECTION

The 7 channel selection switches

- TAPE

In the center position of this switch, all tape inputs and outputs are disconnected and

the MONITOR switch is deactivated to provide the best sound accuracy.

The other positions, controlled by red Led's on the front panel are :

- PB 1 :

Connects the TAPE1 machine. To play the machine or

monitor the recording, use the MONITOR ON position.

The recording can be made simultaneously on the TAPE2

machine.

- PB 2 :

Same for the TAPE2 machine.

- COPY 1-2 :

The TAPE2 machine can record directly the

playback of the TAPE1 machine. The MONITOR switch allow to

listen to, either the TAPE1 source machine in OFF position

or the recording made by TAPE2 in ON position.

- COPY 2-1 :

Same with both machine exchanged.

- MONITOR

Allows the control after recording or during a recording session with three heads

machines.

(see above TAPE)

- ABSOLUTE PHASE

This switch reverses the polarity of the signal simultaneously on both channels. See

paragraph 8 below. To indicate that the unit is playing in opposite phase, the “180”

led is glowing.

7 - INTERNAL ADJUSTMENTS

The Goldmund Mimesis 22 preamplifier main unit provides on its main board

separate impedance and level adjustments for each input.

Those internal adjustments are provided for special source connections and can be

left for conventional use at the factory-adjusted OFF position .

8 - SOUND QUALITY OPTIMIZATION

- Warm-up sonic effect.

If the preamplifier has been left unpowered for a few days, the optimum sound quality

is only reached after many hours. The critical circuits have to warm up to around +55

degrees Celsius (+131 degrees Fahrenheit) before achieving their optimal

performances. This is why Goldmund recommends to leave the MIMESIS 22

powered on.

- Absolute phase.

Your preamplifier has an absolute phase inverter switch. For each source, one of the

two position is optimum. Most of the record are recorded without care for the

absolute phase. Different LP's can have different optimum positions. The absolute

phase optimization is less critical and can be difficult to achieve with CD's since, at

the current state of the technology, the phase coherency of this source is not

sufficient to allow a sufficient difference between the two positions.

- The GOLDMUND exclusive "Mechanical grounding".

In the Goldmund Mimesis 22 preamplifier, Goldmund implemented the same special

construction used in most of its other products : an optimized vibration evacuation

path.

To get all the benefits of this improvement, the MIMESIS 22 must be located on a

very rigid support, directly coupled to the building. Try various location until you find

the most rigid one. Avoid any decoupling material, carpet especially, even between

the furniture and the floor. Or use pin-point supports to couple the furniture to the

floor. Or better, use one of the Goldmund table elements which are made to provide

the best Mechanical Grounding to several Audio Components assembled in a single

structure.

With a very top system, the sonic improvement when the proper grounding is found is

obvious and worth the try.

9 - SAFETY FEATURES

The Goldmund Mimesis 22 preamplifier uses a special protection circuit to protect the

power amplifier and the speakers against a power supply failure or an AC shut-down

of the preamplifier.

10 - MAINTENANCE

The Goldmund Mimesis 22 preamplifier usually requires no maintenance. For the

audio purists who want to keep their preamp sounding as new, we only recommend

that after a year or two, you have a technician or an official Goldmund representative

readjust the DC offset. This very simple operation takes only two minutes and will

give you the safety of long years of unmatched sound quality.

To clean your Mimesis use only a soft, slightly wet cloth. Always turn the power off

before cleaning your preamplifier.

TECHNICAL DATA

OUTPUT LEVEL

- Nominal level : 1.55 V RMS.

- Maximum output level : 40 V RMS.

- Output stage output impedance : < 10 Ohms.

- Corrected output impedance : 600 Ohms.

FREQUENCY RESPONSE

These values for any level to 35 V RMS.

- +/- 0.1 dB, 0 - 150 kHz.

- +/- 1 dB, 0 - 500 kHz.

Tabla de contenidos

Otros manuales de Amplificador de Goldmund

Goldmund

Goldmund Metis 5 Manual de usuario

Goldmund

Goldmund MIMESIS 22 SIGNATURE Manual de usuario

Goldmund

Goldmund MIMESIS 37S Manual de usuario

Goldmund

Goldmund MIMESIS 29M Millennium Edition Manual de usuario

Goldmund

Goldmund MIMESIS 28 Manual de usuario

Goldmund

Goldmund TELOS 352 Manual de usuario

Goldmund

Goldmund SRI2 Manual de usuario

Goldmund

Goldmund TELOS 360 Manual de usuario

Goldmund

Goldmund TELOS 400 Manual de usuario

Goldmund

Goldmund SR150 Manual de usuario

Goldmund

Goldmund MIMESIS 11 Manual de usuario

Goldmund

Goldmund METIS 2 Manual de usuario

Goldmund

Goldmund TELOS 250 Manual de usuario

Goldmund

Goldmund MIMESIS 16 Manual de usuario

Goldmund

Goldmund MIMESIS 27.5 Manual de usuario

Goldmund

Goldmund MIMESIS 24 Manual de usuario

Goldmund

Goldmund TELOS 390 Manual de usuario

Goldmund

Goldmund TELOS 3500 Manual de usuario

Goldmund

Goldmund SR8 Manual de usuario

Goldmund

Goldmund GOLDCUBE Manual de usuario

Goldmund

Goldmund TELOS 350 Manual de usuario

Goldmund

Goldmund Metis 5 Manual de usuario

Goldmund

Goldmund MILLENNIUM Manual de usuario

Goldmund

Goldmund MIMESIS 330 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario